Wing box

Hover · click · blue opens linked boxes · GitBoat A17 · eight wires, below the deck

SLIP RING INTO THE HULL · BELOW THE DECK ON THE WING, NOT IN THIS BOX 24 V from the hull main bus. 16/2 on its own 5 A breaker. Which stud is open.Bus 24 Vstud open 5 A fuse, then a 1.5KE33CA across the 24 V pair.5 A + 1.5KE33CAactuator feed Ring power lead. Rings 1 and 2 are the 24 V pair; rings 3 and 4 are the compass RS-485 pair.Ring powerrings 1-4 WitMotion HWT905 on a G10 pad on the tip cap. Tip-branch 24 V after the 1 A fuse, ahead of the tip 5 V converter. Not in this box.HWT905tip cap, 24 V, rings 3-4 COMPASS RS-485 One shielded Cat6 to the USB hub box: the CAN pair, both RS-485 pairs and a ground pair. Shield grounded at this end only.Hub cableshielded Cat6to the hub box Third Taidacent RS-12V/2S surge module on the compass pair. Then the hub cable.TaidacentRS-12V/2S compass Tip box at the wing tip: the 1 A inline fuse on the tip 24 V branch and the DROK 24 to 5 V for the CMI1017 only. Not in this box.Tip box1 A fuse · DROK 24 to 5 V CAN PAIR Taidacent RS-12V/2S on the slip-ring CAN pair. Then the hub cable.TaidacentRS-12V/2S CAN Rings 8, 9 and 10. CAN H, CAN L and shield. The actuator's own short CAN link.Ring CANrings 8-10 Thomson Electrak MD on the wing, past the ring. The link's 120 ohm at the actuator end. Not in this box.Electrak MDon the wing · 120 Ω at the actuator TIP METER RS-485 Second Taidacent RS-12V/2S on the tip meter's RS-485 pair. Then the hub cable.TaidacentRS-12V/2S 485 Rings 5, 6 and 7. Tip wind meter RS-485 A, B and shield.Ring RS-485rings 5-7 Calypso CMI1017 at the wing tip. 5 V is made at the tip, never 24 V on the meter.CMI1017tip, 5 V from the DROK Readers are in the USB hub box. Not drawn in this wing box. 24 V to MD 24 V to HWT905 5 V to CMI1017 CANH CANL power UART RS-485
Status notes
  1. Boom pocket build (10-30) Decided

    The plug is a Deutsch DTM 4-pin at the actuator only (Trim Guide: Mike, 2026-10-29, "Yes On the plug"). Crimp DTM04-4P and DTM06-4S with wedgelocks and size 20 stamped contacts onto the Thomson lead and the cable.

    Decided 2026-10-29 (Mike: "Yes On the plug"): Deutsch DTM 4-pin (DTM04-4P and DTM06-4S, size 20 contacts) in place of the DT: use size 20 stamped contacts and the JRready open-barrel crimper kit that comes with 50 pairs of them (Amazon B0DZX8723C, price not checked). Both are on the order tracker's Buy list, and the five old spring link rows there are marked on hold.

    The latest sheet now draws: Plug on the actuator's lead (it comes with bare wires): a 4-pin Deutsch DTM pair, DTM04-4P and DTM06-4S, with wedgelocks ( MUYI DTM kit ), and size 20 stamped contacts crimped with the JRready crimper kit , which comes with 50 pairs; prices not checked. It sits above the motor, wherever the lead reaches; grease it and boot it. Still on that sheet: spring link, caps turned round to 0.95 in.

    (ddd) No breakaway, decided 2026-10-30. (vv) Pushrod back to 1/4 in, decided 2026-10-29.

    Boom-root pocket build, 2026-10-30, fourth edition (Build sheet: Wing_Boom_Pocket_Build_2026-10-30, page 3). (eeee) G10 tab with a 2 in gap, decided 2026-10-30. The actuator end is a 1/4 in G10 tab, 3/4 x 4 in. The pushrod is about 46-3/4 in. The short tube is 4-1/2 in. (ttt) Taller tip rod: no, decided 2026-10-30. The tip rod on the rig drawings stays 12 in above the tip. Lightning Guide 5.1 bolts the wing strap to a mast-base gusset, not a clamp, and 5.2 has no wire and no braid jumper.

    Boom-root pocket build, 2026-10-30, latest sheet (Build sheet: Wing_Boom_Pocket_Build_2026-10-30, page 3).

    Boom-root pocket build, 2026-10-30, PDF, latest sheet (Build sheet: Wing_Boom_Pocket_Build_2026-10-30, page 3).

  2. One-piece tail (10-30) Decided

    (kkk) One-piece tail decided 2026-10-30 (Mike: "yes 1 piece"): the tail as Reference/Tail_One_Piece_2026-10-30 draws it.

    The tail flap is the hinged back of a fixed one-piece tail, bolted solid to the boom behind the wing (Build Guide 6.1).

    2nd edition, 2026-10-30: horn and pushrod on the far-face side; pushrod about 46-3/4 in. The give-way spring at the flap is the wind-load fuse (Wing Trim Actuator Guide). Horn 2 in. No stop pins. The axle is not glued (item 463).

  3. Actuator end (10-30) Decided

    Later sub-items, written in the v10.4 guides: (nnn) Two decided 2026-10-30 (Mike: "yes flat tab", "yes 1/4"): (1) the actuator end as Reference/Actuator_End_2026-10-30 draws it, (eeee) the actuator end is a 1/4 in G10 tab, 3/4 x 4 in, with 2 in of bare G10. No lightning wire comes here. The actuator's front fork drives the pushrod through a flat tab of 1/4 in G10, with 2 in of bare G10 between the clevis's metal and the fork's tips (Lightning Guide 5.1). (2) the boom root's two glued G10 plates go from 1/8 in to 1/4 in.

    pdf retired upstream 2026-11-02.

  4. Wing lightning wiring Decided

    Wing lightning wiring, 2026-10-30. The root run carries the tinned 18/4 shielded actuator cable, the wing cable, and the bare 8 AWG lightning ground wire, all pulled in before the 1/2 in tube is glued. No outside fairing, no metal clamping plate. The tip rod on the rig drawings stays 12 in above the tip.

  5. Flap spring horn Decided

    The give-way spring at the flap is the wind-load fuse (Wing Trim Actuator Guide). That guide names Flap_Spring_Horn_Build_2026-10-31 and Flap_Spring_Horn_Explained_2026-10-31. (a) no glue on the flap axle and (b) spring 9287K47 are settled.

    Proposal: still open in Pending 463 are (c) tail slot clearance, (d) the surge-clamp sheet, (g) the 3/16 in pushrod and the unanswered lightning and surge lines, and (h) through (m).

  6. Actuator surge clamps Proposal

    Actuator surge clamps, 2026-10-31. Html only. No pdf upstream. Pending 463 (d), Mike's read of this sheet, stays a proposal.

  7. Box plan Decided

    Wing box plan. Electronics plan A17: six glands, all on the bottom wall, four PG9 and two PG7. Gland 6 is Pi B's CAN drop, in the upper row above gland 5. Which hull cable takes which gland is still open. The box is a TICONN 5.9 x 5.9 x 3.5 in, to buy. The wing has no battery, panel, charge controller, radio, computer or charging link, and no pod (A14).

Earlier proposals & superseded sheets (12)
  1. Boom root actuator (10-27) Proposal, needs Mike's yes

    Boom Root draws PEX, 7/8 in outside, 24 in back, in the boom face (Josh's plan, decided), and says: Replaced for the actuator spot and the PEX route by Wing_Actuator_Forward_Option_2026-10-27 (actuator forward, hanging, on a cradle; one vertical PEX at 12 in with a branch). The boom, tail, joints and guide problems on these pages still stand.

    The boom-root hardpoint at 47 in is the clamp block beside the pocket. No outside fairing, no metal clamping plate. This paragraph does not move that spot.

    Boom root and actuator (proposal, Pending 462)

    Wing_Boom_Root_and_Actuator_2026-10-27.html retired upstream 2026-11-02 (moved to Old/).

  2. Actuator forward (10-27) Proposal, needs Mike's yes

    The root run carries the tinned 18/4 shielded actuator cable, the wing cable, and the bare 8 AWG lightning ground wire, all pulled in before the 1/2 in tube is glued. No outside fairing, no metal clamping plate. The give-way spring (the wind-load fuse) is at the tail flap, not in the pushrod.

    Neither PEX station is the settled route.

    Forward Option draws one vertical PEX 12 in back of the nose. Pending 461's pick is 12 in from the nose, with the side branch about 24 in from the nose. Both drawings are proposals awaiting Mike, not decided design. The root run carries the tinned 18/4 shielded actuator cable, the wing cable, and the bare 8 AWG lightning ground wire, all pulled in before the 1/2 in tube is glued. No outside fairing, no metal clamping plate. The give-way spring (the wind-load fuse) is at the tail flap, not in the pushrod.

    Actuator forward option (proposal, Pending 461)

    Wing_Actuator_Forward_Option_2026-10-27.html retired upstream 2026-11-02 (moved to Old/).

  3. Wing rig cutaway (10-26) Superseded

    The cutaway still says Wire tube in back edge; last 1 in solid. That label is superseded by Pending 454: the wing wiring tube moves off the trailing edge (Mike, 2026-10-27: "pex is specced for the wing"). The tube is one 10 ft stick of 3/4 in PEX water pipe, 7/8 in outside.

    Pending 454 writes a straight channel centered 24 in back from the nose.

    Wing rig cutaway (superseded by Pending 454)

  4. Boom pocket (10-29) Superseded

    The build sheet is now dated 2026-10-29 (Wing_Boom_Pocket_Build_2026-10-29; Mike: "how about todays date on todays file?"). That 2026-10-29 sheet was superseded by the 2026-10-30 sheet. Build sheet: Wing_Boom_Pocket_Build_2026-10-30, page 3. The 2026-10-28 sheet is a superseded step. No outside fairing, no metal clamping plate.

    Part 1 work: redo Wing_Boom_Pocket_Build_2026-10-29 for what is now decided: 1/4 in root plates, no spring link (the give-way is at the flap), the flat tab end, the pushrod straight from the actuator, and the boom root strength numbers in Reference/Boom_Root_Strength_Calc_2026-10-28 with no breakaway.

    The 10-29 sheet still draws the spring link with caps turned round to 0.95 in, the 1/8 in G10 bolt plates, the front tongue on the spring link's front stud, and a Breakaway, 60 lb column. Those drawn lines are not the decided sub-items. The 10-29 file is a superseded step.

    Boom-root pocket build, 2026-10-29, superseded step. The sheet still draws the spring link (caps turned round to 0.95 in), the 1/8 in G10 bolt plates, the front tongue on the spring link's front stud, a Breakaway, 60 lb column, and a core 50 in long. Boom-root pocket build, 2026-10-29, PDF, superseded step.

  5. Boom pocket (10-28) Superseded

    Wing Construction Guide: Makes: one rectangle pocket inside the wing, on its center line, holding the actuator under a screwed lid, and beside it a solid clamp block that takes the boom. No outside fairing, no metal clamping plate. Build sheet: Wing_Boom_Pocket_Build_2026-10-30, page 3. The actuator's mount and the pushrod: Trim Actuator Guide sec 4.

    Boom-root pocket build, 2026-10-28, superseded step. Boom-root pocket build, 2026-10-28, PDF, superseded step.

  6. Boom bay (10-27) Superseded

    Boom bay, superseded step. Boom bay PDF.

    Wing_Boom_Bay_2026-10-27.html retired upstream 2026-11-02 (moved to Old/).

  7. Boom build-out (10-28) Superseded

    Boom build-out, superseded step. Boom build-out PDF.

    Wing_Boom_Build_Out_2026-10-28.html retired upstream 2026-11-02 (moved to Old/).

  8. Boom pocket simple (10-28) Superseded

    Boom pocket simple, superseded step. Boom pocket simple PDF.

    Wing_Boom_Pocket_Simple_2026-10-28.html retired upstream 2026-11-02 (moved to Old/).

  9. Flap spring fuse (10-29) Proposal, needs Mike's yes

    B. One torsion spring at the flap's hinge (Reference/Flap_Spring_Fuse_2026-10-29. Mike's choice asked 2026-10-29. (ss) Hinge spring drawn in detail, 2026-10-29. Reference/Flap_Spring_Fuse_2026-10-29 is now two pages.

    So nothing is to be bought for the link yet. That sentence is the 2026-10-29 hold in (rr).

    One torsion spring at the flap's hinge (Reference/Flap_Spring_Fuse_2026-10-29). Earlier proposal, changed from by (uu), not the decided give-way. The decided give-way is the spring at the flap (Wing Trim Actuator Guide). (nnn): no spring link (the give-way is at the flap). One torsion spring at the flap's hinge (Reference/Flap_Spring_Fuse_2026-10-29), PDF.

  10. Tail assembly (10-29) Superseded

    Reference/Tail_Assembly_2026-10-29 (tail on top) and Reference/Tail_Centered_2026-10-30 (split tail) are superseded.

    Reference/Tail_Assembly_2026-10-29 (tail on top) and Reference/Tail_Centered_2026-10-30 (split tail) are superseded (Pending 463 (kkk)). Not the current proposal. Reference/Tail_Assembly_2026-10-29 (tail on top) and Reference/Tail_Centered_2026-10-30 (split tail) are superseded, PDF (Pending 463 (kkk)).

  11. Tail centered (10-30) Superseded

    Reference/Tail_Centered_2026-10-30 is set aside (Pending 463 (fff)). Reference/Tail_Assembly_2026-10-29 (tail on top) and Reference/Tail_Centered_2026-10-30 (split tail) are superseded (Pending 463 (kkk)). Not the current proposal. Reference/Tail_Centered_2026-10-30 is set aside, PDF (Pending 463 (fff)).