Wing from the Aluminum Plate Up

Wing from the Aluminum Plate Up

Prime Ranger's wing rig, everything above plate 1. Drawn to scale from the v10.3 guides, 2026-10-26.

wing 78 in tall (6.5 ft) nose to back edge 27.7 in can 21 in pivot axis, 6.93 in back from the nose box spar, 4 x 3 in, 8.31 in back wire tube, then 1 in solid glass Lightning rod, 1/4 x3/4 in stainless bar,12 in above the tip Wind meter (backup) Tip box: 5 V converterand 1 A fuse Copper strap, 1 in,glued down the spar(lightning path) Skin: 3 glass layerseach side, 6 at nose.White paint, no carbon 104 foam ribs, every3/4 in, machine cut,stacked on the spar Glass socket, 26 indeep: mast glued inplus two 3/8 in bolts Nose locker: lead barsup to 24 lb. Lid, vent,two drains, 6 bolts Root closeout: breatherand weep hole Water-shedding disc,about 28 in across Mast plate, 15-1/4 in,3/4 in thick, 6 gussets 12 main bolts, 3/4 in:heads welded underdeck, 2 bronze nuts Plate 1: 36 x 36 x1/2 in ALUMINUM,glassed to the deck Tip cap: bird spikes and wing compass G10 block, 5 in, in the spar top:rod and meter arm bolt to it Fixed tail, 27 x 11 in, weathervanes the wing Pushrod on the boom. Its spring linklets a gale push the flap straight Actuator in a sealed fairing, 47 in up Breakaway link (snaps at a bird strike) Tail flap: back 2-3/4 in, 3 pin hinges,the only moving part. A spring centers it Wire tube in back edge; last 1 in solid Wires cross the root into the mast bore Mast: 3-1/2 in heavy-wall stainless pipe.The fuse: it bends first Turning bearing, 20.4 in: inner ring turns Can lip: 3/4 in ring, 20-3/4 in, 16 gussets Drive tube turns the slip ring Slip ring: 8 wires cross the turning joint Hand-hole, 7 x 9 in (one of two) Fixed wires leave low on the can wall Plate 3: 24 x 24 x 1/2 in stainless,12 gussets; rear hinges, rig folds back
Side view, cut open to show the inside parts: spar, ribs, socket, wire tube, actuator and pushrod, the lead rack in the locker, and the slip ring and drive tube inside the can. The copper line is the lightning strap. Heights of the bearing stack are drawn close, not exact.

3D view

Drag to spin the view. Scroll or pinch to zoom.
wing, boom, tail (fiberglass) stainless (plates, mast, rod) aluminum plate 1 painted steel can turning bearing copper lightning strap

What you are looking at

From the bottom up: plate 1 (36 in aluminum, glassed to the deck, the watertight layer), plate 3 (24 in stainless, nutted onto the 12 main bolts, with the fold hinges at its back edge), the can (16 in painted steel tube, 21 in tall, slip ring inside, hand-holes to reach it), the bearing on the can's lip, the mast plate and mast (3-1/2 in heavy-wall stainless pipe, glued and bolted into the wing's socket), and the wing: 6.5 ft tall, 27.7 in deep, foam ribs under a fiberglass skin. The boom carries the fixed tail; the tail flap on the tail's back edge is the only moving part. The nose locker holds the lead that balances it. At the tip: the wind meter, the wing compass, bird spikes and the lightning rod, whose copper strap runs down the outside of the skin to a gusset at the mast base. Everything above the bearing turns together; the "turn the wing" slider shows what moves and what stays.