USB hub box (A1a)

Beside Pi A | GitBoat v10.5 A1a | Bus: none | own 5 A breaker

Status notes
  1. Box plan Decided

    As built: three glands on one side wall, two large splits with a small gland between them. None on the top or bottom wall. Which cable takes which gland is open.

  2. Hub glands Decided

    Electronics plan A1a, as built: three glands, all on one side wall, two large split glands with a small gland between them, none on the top or bottom wall. The hub keeps its 12 V converter. The 5 V lead ends in a DC barrel plug and enters by one of the three glands. Still open: which cable takes which gland, and where the wing Cat6 lands.

As built: three glands on one side wall, two large splits with a small gland between them. None on the top or bottom wall. Which cable takes which gland is open. One of three side-wall glands. Hub 5 V from Pi A entry 12 enters by one of them, not a PG7 of its own. The 3 A fuse is in the Pi A box. Which gland is open.small gland1/2 in, 5 V One large split gland on the side wall. Which of the hub lead, wing cable, SBMS0 lead, AIS coax and MOTU lead takes which gland is open.large splitM30, 1-3/16 in hole S port b. Mike's shielded Cat6 on hand, about 5 ft (Pending 446, Cat6). Plugs cut off. Shield grounded at the wing box only.b wing cable SBMS0 USB lead in by S port c, into a hub port. No isolator on this lead.c SBMS0 MOTU M2 USB lead in by S port e from its own box, into a hub port. That box is not picked and not drawn.e MOTU lead YRDZXG 24 to 12 V. Feeds BaroVUE and HygroVUE only. No fuse. A 1.5KE33CA across its 24 V input at TB1-1 and TB1-2.YRDZXG24 to 12 V StarTech USB210AIND, 10-port hub on M3 nylon standoffs. Two ports spare. 5 V from gland T.StarTechUSB210AIND, two spare DSD TECH SH-C30G on a hub port. 120 ohm on. Waveshare terminators off.SH-C30G120 ON ยท hub dAISy 2+ on a hub port. AIS coax in by S port d, PL-259 on, Superbat SO-239 female to BNC male (#573). No SMA.dAISyhub port Waveshare USB TO 2CH RS485, SKU 27646, on one hub port. Terminators off. CH1 tip meter, CH2 compass.Waveshare2CH RS-485 LiuDr SDI-12 USB Adapter, black, Tindie Sep 2026, on a hub port. Top-left block: left minus, middle S, right plus empty. HygroVUE address 1, set with 0A1! before the BaroVUE joins at address 0.SDI-12LiuDr TB1, nine terminals. 1 +24, 2 to 5 0V, 6 to 7 +12, 8 to 9 SDI. Bridges 2 to 5, 6 to 7, 8 to 9. 1.5KE33CA across 1 and 2.TB11 +24, 2-5 0V, 6-7 +12, 8-9 SDIbridges 2-5, 6-7, 8-9 TB2, nine terminals. 1-4 A B A B, 5-7 G G G, 8 H, 9 L. Bridge 5 to 7. Shield trimmed flush, sleeved, touching nothing.TB21-4 A B A B, 5-7 G, 8 H, 9 Lbridge 5-7. Shield touches nothing 1.5KE33CA surge diode across the 24 V input, TB1-1 to TB1-2, ahead of the YRDZXG. Legs short and sleeved. Works either way round.TVS The 24 V in crosses one of the three side-wall glands. None of those glands is on the top or bottom wall. Which gland is open.side gland5/8 in, 24 V The other large split gland on the same side wall. Which cable takes which gland is open.large split1-3/16 in hole Split gland B, port 2. BaroVUE 10 own Campbell cable, 30 in, whole. Sensor inside the hull within reach of this gland. Pending 449.2 BaroVUE Split gland B, port 3. HygroVUE 10 own Campbell cable, ships 5 m. Mount spot open. Pending 449.3 HygroVUE Split gland B, port 5. DO sensor FTDI USB-RS485-WE-1800-BT. Hub port, bare end to wet lab entry 12.5 DO Split gland B, port 4. SBE 45 FTDI USB-RS232-WE-1800-BT-0.0. Hub port, bare end to wet lab entry 14.4 SBE 45 S port a. Hub USB lead out to Pi A USB 1.a hub out S port d. AIS antenna coax in, PL-259 on, into the Superbat SO-239 female to BNC male jumper (#573), then the dAISy.d AIS coax CANH CANL power USB Ethernet UART I2C GPIO coax SPI RS-485