Electronics CAN Sources list

Pending Amendments v10.6

Written 2026-11-09 at the v10.5 promotion. v10.5 is the v10.4a guides with every decision made through 2026-11-09 written in: the boxes and battery boards as built (the central node, USB hub, wing, wet lab and VESC A boxes); bilge pump 2 with no cutoff (the BatteryProtect dropped); no fuses on the battery tap and shunt sense wires; plugs on the CAN boards and every Nucleo solder link left as shipped; no inline fuse in the release feeders; "release" in place of "fire"; no box for Starlink; and pointers to the box plans, now Box Plans v10.5/. The "Closed at v10.5" list near the end names each, with its full text. This is the only open list. Part 1 is work with nothing left to decide. Part 2 is questions for Mike. Item numbers keep their v9.9 meaning. New items start at 469; the box plans added 499 to 501 (2026-11-01); the bulkhead angle nuts are 502 (2026-11-02); the Old folder is 503 (2026-11-02); the barometer guide rewrite is 505 and its two questions 506 and 507 (2026-11-02); the central node box is 508 (first written as a second 505, renumbered 2026-11-02); the SBMS0 ribbon is 509 (2026-11-02); the rewrite of the other guides is 510, its leftovers 511 and its questions 512, Mike's answers 513 (2026-11-02); the battery board change plans are 517 and their question 518 (2026-11-03); the USB hub box as built is 519 and the wrong TICONN link 520 (2026-11-04); the CAN board's soldered header is 521 and the wet lab running without CAN 522 (2026-11-05); the tape on inside lightning joints is 523 (2026-11-06); the Orion-Tr on/off wire size is 531 and the bus board drawing redraw 532 (2026-11-08); the v10.5 write-in leftovers are 537, the CAN board resistors 538 and easy soldering 539, the Central Node plan trim 540, file names 541 and the order tracker name 542 (2026-11-09; the file names item was first written as a second 540). The motor's M20 ports are 549, the Buy list link fix 550, the ready-wired actuator plug 551 and the rig base edge bolt count 552 (2026-11-09). The Central Node plan's two added layout pages are 568 (2026-11-10). The closed record is the "Closed at v10.5" list and the lists after it near the end of this file; the v10.5 open list as it stood before the promotion is Old/Pending_Amendments_v10_5.md; older closed lists (v10.2a and before) and the full text of every item closed at v10.4 are in Old/Pending_Amendments_v10_4.md, with earlier ones in Old/Pending_Amendments_v10_3.md and before. (The Archive folder was renamed Old on 2026-11-02, item 503: read any Archive/ path in this file as Old/.) Software items live in the software repo. ---

Part 1. Work with nothing left to decide

1A. Decided, not yet in a document or drawing

568. Central Node box plan: the power and release wires drawn on the true layout too, now 8 pages (Mike, 2026-11-10: "Page 3 missing a lot of wires, why?", then "yes please"). Page 3 drew only the 83 control and sensor wires; the 147 others (0 V, 24 V, release, steering motor, shields) were on no layout page since the trim in item 540. Two pages added in the same style as page 3, each wire its own color on the to-scale layout: page 4 power and 0 V, page 5 release and steering motor. The Nucleo corner and top rail is now page 6, the middle and bottom rails page 7, every wire page 8. Done 2026-11-10. *Documents: Box Plans v10.5/Central Node v10.5.*

567. Release Node B's release cables to the drogue boxes: 14/2 tinned duplex from the roll on hand, glands 3 and 4 PG11 with sealant (Mike, 2026-11-10: "yes, please redo page 5 with red and black and 14/2"). One 14/2 per drogue box, red + and black −: box 1 red to 12t, black to 13t (gland 3); box 2 red to 11t, black to 14t (gland 4). 14 AWG matches the central node's 14/4 pairs on the same 30 A breaker. The duplex jacket is oval, so glands 3 and 4 go from PG7 to PG11 (3/4 in hole), filled with sealant like gland 2; hole 3 moves to 8-3/4 in from the plate's left end so the two PG11 nuts clear. Done 2026-11-10 in the Release Node B plan (pages 1, 2, 4, 5). *Documents: Wire and Cable Buy List (name the 14/2 for Release Node B's release cables); Electronics plan A15 glands.*

566. Release Node B's CAN board: pin order and plug lead colors from Mike's photo of 2026-11-10 (Mike: "Update drawing and wire color please"). The board's header reads 3.3V, GND, CAN RX, CAN TX, with CANL and CANH on its two-screw terminal (CANL on the 3.3V side). Its 4-pin plug's leads: red 3.3 V, black GND, white CAN RX, yellow CAN TX. So: red to Nucleo 3V3, black to 6t, yellow (CAN TX) to D2, white (CAN RX) to D10; CANH to surge OUT 1, CANL to OUT 2. Done 2026-11-10 in the Release Node B plan (pages 2, 4, 5). *Documents: none beyond the plan.*

565. CAN surge parts: H on line 1, L on line 2, in every box (Mike, 2026-11-10: "want to be consistent with the industry"). No standard covers a two-line surge part (Phoenix Contact puts H on 1 on one model and L on 1 on another; the Helox RS-12V/2S has no H or L marking), but H before L is the common habit (CiA 106: RJ45 pin 1 H, pin 2 L; M12 pin 4 H, pin 5 L). Release Node B and the wet lab box already use 1 = H (white), 2 = L (blue), IN 1 to OUT 1. The central node plan says only "line H, L": read it as 1 = H, 2 = L. *Documents: Central node box plan (name the numbers when next edited).*

564. Release Node B: the 14 AWG wire colors inside the box (Mike, 2026-11-10: "we only have red and black 14gauge"). Red for relay H's COM and NO; black for both MOSFETs' VIN− and OUT−. Each OUT− wire (horn return, blocks 13 and 14) carries a label at both ends, HORN 1 RETURN or HORN 2 RETURN, because it is not 0 V while its MOSFET is off. The drawings keep orange for the horn path (drawing colors show what a wire does). Done 2026-11-10 in the Release Node B plan, page 4. *Documents: none beyond the plan.*

563. Release Node B laid out as Mike's plate photo of 2026-11-10 (Mike: "Redo based on this layout please", "keep it sideways"); the Klnuoxj stays its 5 V converter (Mike: "not drok, the 24 to 5 that looks like the 24 to12"; on the shelf: "yes"). The plan's pages 2 and 5 are redrawn from the photo turned a quarter turn (photo top = page right): the Nucleo on its carrier top left, the converter top middle (hangs about 1/2 in past the plate edge, as in the photo), the enable relay top right, the strip under the relay with block 1 at the left (red 1-3 24 V bar, green partition, black 4-9 0 V bar, orange 10-12 release bus, yellow 13, 14 horn returns, as in the photo), the two MOSFET boards along the bottom (MOSFET 1 the left one), the CAN surge part lower left on its rail stub with its IN end at the left. Not in the photo, Claude's picks: the CAN board between the Nucleo and the surge part; about 1/2 in between the relay and the strip and between the strip and the MOSFET boards (the strip's wire holes face them; the photo has the relay touching the strip); the four holes in the bottom wall at 3/4 in (1, CAN), 4-7/16 in (2, 24 V), 8-15/16 in (3, box 1) and 9-7/8 in (4, box 2) from the plate's left end. The plate is 250 x 150 mm (9-7/8 x 5-7/8 in); the box size is still not known, and the plan's old 7.9 x 5.9 in guess is smaller than the plate. The 24 to 12 V YRDZXG in the photo is a stand-in; the Klnuoxj 24 to 5 V goes there (the Nucleo's 5V pin takes 5 V). MOSFET board screws named from Mike's photos of the board: big VIN-, VIN+, OUT+, OUT-; small LOW/SWITCH, GND, HIGH/PWM. The Nucleo wire goes to HIGH; LOW and OUT+ stay empty. Strip screws reassigned for the new layout (t = relay side, b = MOSFET side): 1 t relay DC+, b gland 2 red; 2 t relay COM; 3 t G red in, b diode; 4 t G black in, b diode; 5 t Nucleo GND, b gland 2 black; 6 t CAN board GND, b MOSFET 1 VIN-; 7 t relay DC-, b MOSFET 1 GND; 8 t CAN drop black, b MOSFET 2 VIN-; 9 t surge PE, b MOSFET 2 GND; 10 t relay NO, b MOSFET 1 VIN+; 11 t D2+, b MOSFET 2 VIN+; 12 t D1+; 13 t D1-, b MOSFET 1 OUT-; 14 t D2-, b MOSFET 2 OUT-. Done 2026-11-10 in the Release Node B plan (pages 1 to 5); the order tracker's Klnuoxj line marked HAVE. Left: the long-form data file (_v105_work/box_plans/boxes/a15_release_node_b.py) still has the old block-by-block screws and the DC+/DC-/TRIG names. *Documents: Electronics plan A15 (MOSFET screw names).*

562. Release Node B: the burn-current wires inside the box are 14 AWG, not 12 (Mike, 2026-11-10: "Why do mosfet DC- have 12awg? Thats BIG", then "yes"). The six wires that carry a horn's 12.5 A inside the box: relay H's COM and NO, both MOSFET OUT− and both MOSFET DC−. 14 AWG matches the 14/4 release cables out to the drogue boxes on the same 30 A breaker (Wire and Cable Buy List C3); 105°C marine 14 AWG is rated 35 A (ABYC), above the breaker, so the fuse sizing rule (Electronics plan sec 7.6) holds. Use 105°C marine wire from the 14/2 or 14/4 on hand. The 12/2 feed's own cores (1b, 4t) stay. The relay's coil wires (DC+, DC−) stay 22 AWG. Done 2026-11-10 in the Release Node B plan (pages 1 to 5) and its long-form data. *Documents: none beyond the plan.*

561. Main bus board: what is left, from Mike's photo of 2026-11-10 (Mike: "can you redo main bus board pdf"). The Main Bus Board Changes plan is redone from that photo (Reference/Main Bus Board Photo 2026-11-10.jpg): page 1 lists what is done and marks only what is left. Done in the photo: both shunts on the + side and plain cable on the − side; the Argodiode mounted with its feed from the branch bar's line 1 stud and its output on; the backup-fed bar pair mounted, as built, directly right of the right column of breakers with its black − bar beside it (not where the Nov 3 plan drew the + bar, still in the open space Mike said yes to); five jumpers on the backup-fed + bar; sense wires on both shunts; the CAN and Bilge 2 breakers unwired. Left: the CAN and Bilge 2 breakers off the board (Bilge 2's to the backup battery board); Aft relabelled Switch; a short 6 AWG black from the backup-fed − bar to the − branch bar; the backup converter's 12/2; the five lines' blacks on the backup-fed − bar; split loom on the long jumpers; covers; the VESC A runs. Not read from the photo (too small to trace): which five breakers the backup-fed bar's jumpers go to; the plan lists the five that must (B Release, A Release, Central, Steering, Wing) and the two that stay on the branch bar (Iridium A, Wet lab). The Main Bus Board v10.5 plan's layout page is redrawn to the same photo: the solar shunt lying across the top left corner, the battery shunt lying below the + 400 A bar, the + 400 A studs left to right A (solar), B (100 A MEGA), D (battery), C (250 A MEGA), the Argodiode's studs in a column, the backup-fed + bar right beside the breakers, the − 400 A bar standing upright at the right (studs 1 to 4 top to bottom); item 532 is done by it. *Documents: Main Bus Board Changes plan; Main Bus Board v10.5 plan.*

560. Release Node B's Nucleo pins: D3 the enable relay, D7 MOSFET 1, D8 MOSFET 2 (Mike, 2026-11-09: "yes", to Claude's "use the same pins as the central node"). The same pins do the same jobs on the central node (D3 its enable relay, D7 and D8 its MOSFET 1 and 2 triggers), so one program serves both boxes and the wiring is the same; none is a pin Compute Bay 10.2 keeps release wires off (D5, D12, D13), and none clashes with CAN on D2 and D10. Done 2026-11-09 in the Release Node B plan (pages 2 to 5; the "pins open" box is gone) and its long-form data. *Documents: Electronics plan A15 (a pin line for the node); Compute Bay Plan sec 10.2 (Release Node B's pin map).*

559. The Argodiode's two jumpers are 12 AWG, not 6 AWG (Mike, 2026-11-09: "12", after "Why 6 gauge from pos into argo diode" and "is 12 enough?"). The feed from the + branch bar's line 1 stud to the Argodiode 80-2SC (about 15 in) and its output 1 to the backup-fed + bar are 12 AWG red, from the 12/2 roll on hand, each in split loom where over 7 in. Why it is enough (worked from the guides' numbers): 12 AWG tinned carries about 45 A; the most through it is about 33 A (one release at 25 A, the central node about 5 A, the wing trimming about 2.6 A, steering paused for a release); the drop over 15 in is under 0.1 V; and sec 7.6 already lets a thin jumper ahead of the breakers ride on the 100 A MEGA alone when it is under 7 in or in split loom. Lugs: Mike had lugs that fit the Argodiode's M6 studs; both wires are connected (Mike, 2026-11-10: "already connected"), so the 1/4 in 12-10 lug 3-pack came off the tracker's Buy list. Drawn in the Main Bus Board Changes plan. At the next write-in: Electronics plan 7.6 (line 1's row "6 AWG, about 15 in" and the backup-fed bar paragraph "about 15 in of 6 AWG ... Its jumpers are 6 AWG (the Kenhihi red and black on hand), on 1/4 in lugs"), BOM 15.4. Also the backup-fed − link (Mike, 2026-11-10: "Wire to argo is 12awg", then "you have 6 for feeding backup fed to, please change both"): the short black from the backup-fed − bar to the − branch bar is 12 AWG too, from the 12/2 roll; it carries the same current back as the Argodiode wire carries out. As built, the Argodiode wires are 12 AWG. Both plans changed (Main Bus Board v10.5, Main Bus Board Changes). At the next write-in, also Electronics plan 7.6's backup-fed − link. *Documents: Electronics plan 7.6; BOM 15.4.*

558. Release Node B: the enable relay's DC+ lead on block 1's top screw (Mike, 2026-11-09: "yes", to Claude's "move the relay's + wire from block 2's bottom screw to block 1's spare top screw"). It no longer runs under the strip; 2b is now spare. Done 2026-11-09 in the Release Node B plan (pages 3 to 5). *Documents: none beyond the plan.*

557. Release Node B: the surge diode on the bottom screws; the wires page redrawn straight (Mike, 2026-11-09: "Also put the diode on 3 and 4 to the bottom, wires to top please"; on the curved wires page: "makes no sense to me", "Please sort it out"). The surge diode J goes across 3b and 4b; converter G's red in moves to 3t and the 12/2's black (gland 2) to 4t. The plan's page 5 is drawn again with straight lines that turn square, each colored by what it carries (24 V, release path, 0 V, 5 V and 3.3 V, CAN, logic), thick for 12 AWG, a white edge where lines cross, and the cables from the four holes in their own wire colors; the parts sit in page 2's zones, pulled apart for room. Both MOSFET boards are drawn with their power screws DC−, DC+, OUT+, OUT− (fewest crossings; the plan says to go by each board's own labels). Done 2026-11-09 in the Release Node B plan (pages 2 to 5). *Documents: none beyond the plan.*

555. Release Node B plan in zones; Central Node plan down to 6 pages (Mike, 2026-11-09: "do the same zone layout for Release Node B"; "Central, can you combine 7 and 8 to one page? And make 4-6 2 pages?"). Release Node B: logic on the left (Nucleo, 5 V converter, CAN board, CAN surge part, CAN hole 1 at the left end); 24 V and release on the right (enable relay, the two MOSFET boards at their listed 1-13/16 x 1-1/8 in, the strip, hole 2 for the 24 V feed and holes 3 and 4 for the release cables below it), so every 12 AWG run stays short. Holes move: 1 at 1 in, 2 at 4-5/8 in, 3 at 6-5/16 in, 4 at 7-1/8 in from the left end (the box size is still a guess). Its wires-on-the-layout page now draws every wire on the true layout, each its own color. Also written into that plan from v10.5: solder links as shipped; the CAN board's resistor snipped and a 24 AWG plug on its header, zip-tied (the screw block and the unsolder step are gone). Central Node: the Nucleo corner and the top rail share one page, the middle and bottom rails one page, and every wire is one page (each joined group a heading, then a line per block): 6 pages. *Documents: Electronics plan A15 (hole spots); the two box plans (done).*

554. Central node plan: zones, fewer blocks, real sizes (Mike, 2026-11-09: "1. no ... the extras might allow flexibility in your laying out; 2. not that helpful, but eliminate (condense) ones like block 59 and 60; 3. yes"; "Page 7 each block on its own line"). Both 8-channel relay boards stay. No DIN distribution blocks; instead every joined (bridged) group is packed two wires to a screw, field cores on the bottom screws first, so no block sits half empty: 65 rail blocks, was 72. Zones: the release blocks (release feed, release bus, release returns, release 0 V) move to their own short rail low on the right, under the MOSFET boards and above holes 10, 11 and the 5-port gland; the four load fuses (ch 1, 4, 6, 9) move from the top rail to the bottom rail beside the load blocks, under relay board 1; the light fuses (F2, F4, ch 7) stay on the top rail with the light blocks. MOSFET boards drawn at their listed size, 1-13/16 x 1-1/8 in. The breakers drawn flat on the right wall, below the relays; holes 17 and 18 at the low end of that wall. The every-wire list gives each block its own line and runs to two pages (the plan is now 8 pages). A wrong color on block 21 fixed. All in the Central Node box plan 2026-11-09. At the next write-in: Electronics plan A3 (rails and block count). *Documents: Electronics plan A3; the Central Node box plan (done).*

553. Central node: AHT30 out, puller breakers picked, relays and holes redrawn (Mike, 2026-11-09: "yes drop AHT30", "Will use these 6a (on hand)" with a photo of the GLOSO E512 6 A 5-pack, "yes draw it", "BME 280 and G2 we can solder ... AHT is out"). (a) No AHT30 in the central node: the XICOOLEE BME280 (2-pack, Sep 7 order) reads humidity too. (b) The four cord puller breakers are GLOSO E512 6 A auto-reset stud breakers, from the 5-pack on hand (Sep 7 order), ring lugs on the studs, covers on; they replace the four puller fuses. (c) The four reversing relays on a short DIN rail on the right wall, upper part, the breakers below them on the same wall. (d) Holes: entries 2 (CAN), 9 (bilge), 12 and 13 (pullers) and 15 (UV-C) share one Altelix 5-port split gland M on the bottom wall; chain 2 (entry 19) takes the right wall split gland 17's spare port d; the right wall's holes and the left wall's 20 and 21 move low on their walls (2 in up), clear of the relays; entry 14 (never drilled) comes off the drawing. 15 holes and the vent, was 21. (e) Soldering stays only on the G2 and the BME280 (Mike can solder those); the expander is the screw-terminal version. All drawn in the Central Node box plan 2026-11-09. Open: the 5-port's port range (the 4-ports seal 0.15 to 0.30 in; these cables are about 0.25 in), and whether a spare 5-port is on the shelf. At the next write-in: Electronics plan A3 (entries and the hole table, the box contents), 4.1 (fuse table and puller guard), Appendix A totals, Compute Bay 10.2 and 10.3, BOM (AHT30 count, the node's glands, the GLOSO breakers' job), Transom Drogue Box Guide (pullers). *Documents: as named; the Central Node box plan (done).*

550. Order tracker Buy list links fixed (Claude, 2026-11-09, from Mike: "link column is off one on some"). From the row taken off on 2026-11-08 (the 30 AWG wire) down, each Buy list link opened the page of the row above: openpyxl leaves a link on its old row when a row is deleted. Every link was set again from its own row, and stray link text on four rows with no link came off. The rows Mike marked x (bought) are off the Buy list, with the DTM plug kit he bought in October; the Order log names them. The 5 A auto-reset fuse 5-pack of 2026-08-16 (Amazon B0DYSDZZ3N) was cancelled 4 minutes after ordering; the Order log now says so. The rules file now says to set every link again after deleting a tracker row. Done.

549. The motor's coolant ports are M20 x 1.5, not M16 (Mike, 2026-11-09: "x (M20 btw)" on the port plug row). Mike marked the plugs bought. The M20 x 1.5 to 3/8 in barb pair of 2026-09-22 (the tracker says "purpose to confirm") was for these ports. Write-in: Bill of Materials motor jacket line and Build Guide sec 5.2 "Filling and plugging the jacket": M20 x 1.5 plugs, each on an M20 bonded seal washer. The tracker Parts row is fixed. *Documents: Bill of Materials, Build Guide.*

548. Central node simplified further (Mike, 2026-11-09: "2. yes 3. yes"; "will mount relays on side of box, upper right or left, whichever shortens the wires"; "Will use 4x and 5x glands on bottom and lower sides"). (a) The wind meter's Pololu D36V6F5 board is gone: the meter (0.25 mA) takes its 5 V from the node's own Klnuoxj 5 V converter (5 A), by a 22 AWG red from the Nucleo carrier's 5V screw to the wind meter block; no board to solder a terminal block onto and pot. Done in the Central Node box plan. (b) Spares left unwired: relay channel 8's coil line (expander PA7) and opto input 2's output (expander PB5). Done in the plan. (c) The four cord puller reversing relays move off the plate onto the upper part of a side wall, the side that keeps their wires shortest (Claude: the right wall, nearer the MOSFETs and the puller cable holes). (d) Multi-port split glands (4-port and 5-port) on the bottom and lower side walls in place of single glands, where the cables are round; the oval duplex runs (16/2, 14/2, 12/2) keep single sealant-filled glands, since a round port cannot seal them. Grouping and hole map for (c) and (d) to be drawn into the Central Node plan. At the next write-in: Electronics plan A3 (entries, the wind sensor paragraph), Compute Bay 10.2, BOM (the Pololu off the central node; glands), Instrument Post Guide 10.4, System Settings Sheet (post meter row), Wire and Cable Buy List (wind meter cable). *Documents: as named; the Central Node box plan ((a) and (b) done).*

546. Central node fuse sizes, and auto-reset breakers on the cord pullers (Mike, 2026-11-09: "yes, make the four changes, also F2 2a; except i think resetting breaker for cord pullers"). Each fuse weighed for help (a short on a cable leaving the node blows one fuse instead of tripping the node's own 15 A auto-reset breaker, which on channels 3, 4 and 9 would come back at every reset and lock the node out, steering and all) against hurt (a blown fuse stopping something important). New sizes, all slow-blow 5 x 20 mm: F2 stern light 2 A (was 1), F4 bow lantern 2 A (was 1; its 60 W converter's switch-on surge), em-trak 3 A (was 2; it peaks about 1 A at 24 V), whites 2 A (was 0.5; converter surge). Unchanged: Starlink 5 A, bilge 1 manual-on 5 A, UV-C 0.5 A, horn 5 A inline. Cord pullers: a blown puller fuse would leave the drogue out and stop the voyage, so each of the four gets a 5 A auto-reset breaker instead of a fuse (above a stalled worm motor's draw, a guess of 1 to 3 A; under the reversing relay's 10 A; protects the 18 AWG), and the one-puller bench test that set the fuse size goes. The 64 s run timer still stops a stalled motor. Mike bought a 5-pack of 5 A auto-reset ATC/ATO blade breakers 2026-08-16 (order log); the holder (a DIN-rail ATO/ATC block) is being checked. Done in the Central Node box plan for the four fuse sizes 2026-11-09. At the next write-in: Electronics plan 4.1 (the fuse table, the puller fire guard paragraph and its bench test), Compute Bay 10.3 and 11, Transom Drogue Box Guide (the pullers' bench test steps 1 and 2), Build Guide 11.1 (the puller bench test), Instrument Post Guide (post fuses line), BOM 15.7. *Documents: as named; the Central Node box plan (fuse sizes done; pullers to draw once the holder is picked).*

545. Fuse F1 (post wind meter, 1 A) dropped (Mike, 2026-11-09: "yes" to Claude's "Drop F1?"). The wind meter's Pololu D36V6F5 has its own over-current and over-heat shutdown (Pololu's spec, from memory), so its 22 AWG feed runs straight from the central node's +24 V blocks to the Pololu's VIN. The node now has eleven DIN fuses (seven outputs and lights, four pullers), sixteen holders boat wide with the wet lab box's five. Done 2026-11-09 in the Central Node box plan. At the next write-in: Electronics plan 4.1 (the fuse table row and the count paragraph), the wind sensor paragraph ("behind F1"), 7.6 "Still fused" list, the parts list (twelve holders, seventeen boat wide); Compute Bay sec 3 box table, the wind meter row and sec 11's holder count; Design Decisions (the node contents, R-8.1B fuse note); BOM 15.7 and 15.8 (holder count, F1); Instrument Post Guide 10.4 and the post fuses line; System Settings Sheet (post meter row); Wire and Cable Buy List (wind meter cable); Box Wiring Sheets A3. *Documents: as named; the Central Node box plan (done).*

544. The expander's thirteen 10k pull-down resistors dropped (Mike, 2026-11-09: "All these resisters seem messy. Better way?", then "yes, drop them"). At a reset the MCP23017's pins come up as inputs with no pull-ups (its datasheet), so they float; each relay board's input is an optocoupler that needs a few milliamps to switch on, so a floating pin leaves every relay off (inferred from how these boards are built). A reset still reads as OFF, the same as with the resistors, and channels 3, 4, 9 and the steering cut relay still rest on their closed contacts. PB6 (the release bus readback, nothing wired) needed none either. The central node keeps three resistors: the 1k in the Ewellix position wire and the two 4.7k on the temperature probe chains. Written in the same day: Electronics plan sec 4 (the expander line, the G2 FLT row, the to-buy line), Compute Bay sec 10.2, Design Decisions (the expander paragraph), Node Boxes Explained, and the Central Node box plan (logic 0 V group 8 blocks to 5; 74 rail blocks). *Documents: as named (done).*

543. Watchdog relay trigger jumper: H (Claude, 2026-11-09, from Mike's photo of the 10-pack of 5 V 1-channel relay boards, CW-025, Songle SRD-05VDC-SL-C). These are the watchdog rail switches (one in the Pi A box for WD-A, one in the Pi B box for WD-B; 8 left over). Each board has a 3-pin trigger jumper. Set it on H (high-level trigger), then a dab of removable silicone. Why (inferred): a dead, unpowered Nano's pin sits near 0 V, and on L a low input pulls the coil in, which would cut its Pi; on H a low or floating input leaves the coil off and the Pi on. The Pi's 24 V goes through COM and NC. To write in: Compute Bay 4.3 and Electronics plan A1, A2 ("if it has a trigger jumper, set it...": say H); the Pi A and Pi B box plans. *Documents: Compute Bay 4.3; Electronics plan A1, A2; Pi A and Pi B box plans.*

540. Central Node box plan trimmed to 7 pages (Mike, 2026-11-09: "Too much for human to read. remove pages 3,4, 5 and 6"). Gone: the two wiring diagram pages and the two pulled-apart wires-on-the-layout pages. Kept: parts, layout, the control and sensor wires on the true layout (each wire its own color, Mike: "can't really tell where some of them go"), the Nucleo corner close-up, the two rail close-ups (labels in plain words, with a line saying what 10k, jumper and hole mean; Mike: "not sure what some words mean (10k from PA6 for instance)") and every wire. Built with the v10.5 facts: Nucleo solder links as shipped, MOSFET 5 and 6 on A7 and D1, the horn's relay on expander PB3, the CAN board's resistor snipped and a 4-pin plug on its header, the Orion pair 16/2 in a PG9. Done. *Documents: Box Plans v10.5/Central Node v10.5.*

537. Left over from the v10.5 write-in (Claude, 2026-11-09). Found by the writers and left as it was; nothing below is decided. *Numbers:* (a) Electronics plan A10 still gives the backup converter "about 26 A at most" beside the 19 A at full output (item 517). (b) The split gland hole: 1-3/16 in (30 mm) in Electronics plan 7.1 and A3 entry 17, against 1-1/2 in for a PG25 in A18. (c) The USB hub box: 11 cables cross its wall, but three glands give about 10 openings (goes with which cable takes which gland, item 519). (d) Bottom Painting sec 1 still says Boat 1 needs about 3.5 gallons ($550-650); at the paid prices four kits come to about $534 to $555. (e) The Bill of Materials Starlink line keeps its $500 estimate though there is no enclosure. (f) The one 50 ft 18/4 roll (Wire and Cable Buy List C4) may run short now the wet lab pump cable is on it. (g) The BOM central node line says 20 glands; item 508 speaks of 15 bottom glands. *Words:* (h) Electronics plan A6 says the TICONN box on hand (about 12 x 8 x 5 in) is free for another job, while the hub box is most likely that box. (i) Electronics plan A9 entries 3 and 3a still say "aft wall" for the glands to the BMS box, now on a long side wall. (j) Compute Bay 5.2 puts pump 2's breaker "on the board's spare breaker spot"; the changes plan puts it below the Pi B and Iridium B breakers. (k) Battery Box guide: "Dress the cables" still has nylon clamps screwed to the long wall (the photos show the wires tied to the PEX rod sleeves); "The temperature probes" step 5 still says "ask Electrodacus"; the parts list still has the 12-pin ribbon "to buy" (Mike has made and used it). (l) Design Decisions counts three hull-glued boxes, the brief four. (m) Build Guide sec 1 still calls the T8 a "fuse". (n) The Glossary keeps an INA226 row (none is fitted) and lists no PG21. (o) Transom Drogue Box Guide 4A: two U-bolts per quarter "one per drogue" against "one per quarter, shared by both drogues". (p) Routing Guide 7.4: "it goes out on the forecast trigger" reads as if the boat lets the drogue go by itself; it is a signed shore command. (q) Barometer guide sec 6: "a cut hose reads cabin pressure" with a rule for a broken post, where the tube reads outside air. (r) Lightning guide 5.1: the boom wire splice still says self-amalgamating tape (item 523 covers inside joints only). (s) Wing Power parts table: the wing box and Pi B's SH-C30G still read "to buy"; check against the tracker. (t) Electronics plan sec 8: the motor controller line lists "12 AWG red and black leads"; as built the minus lead is red with black shrink. (u) BMS diagram: its probe trunk row says the trip "isolates the bank", Box Wiring Sheet A9 says nothing cuts the bank off on the trip (goes with item 352 and 353 (d)). (v) Box Wiring Sheet A14 still has "Open: which stud feeds it", though the wing box is on the backup-fed bar. *Drawings:* (w) Box Wiring Sheets: A1a gland spots, A10 parts at their as-built spots, A9's BMS box mark on the end wall, the six-block shunt strip on A4 and the BMS diagram, A18's 38-block rail. (x) The BMS Box Wiring Diagram prints its labels at about 8 pt, under the 9 pt rule; a bigger font needs a re-layout. (y) The box plans' long-form data still has the Starlink box (A13) and the wet lab box's old glands (A18), so Box Plans Cross Check v10.5.pdf flags them; the 4-page plans are right. *Documents: as named.*

538. The three CAN boards' own 120 ohm resistor: snipped off (Mike, 2026-11-09: "I will snip them off if needed"; Claude: needed). Each SN65HVD230 CAN board (central node, Release Node B, wet lab box) carries a 120 ohm resistor across the bus, and the molded end plugs are meant to be the only two terminators (Electronics plan 5.1). Left on, the house bus (two molded ends plus Release Node B and the wet lab board) sees about 30 ohms and the control bus (two ends plus the central node board) about 40, against the 60 ohms the drivers are made for (computed; inferred that this shrinks the signal enough to matter). Mike snips each resistor off with flush cutters, no heat; this replaces taking it off with a soldering iron (item 500 (a)). Written into Electronics plan 5.1 (2026-11-09). Still to do: one line on the Release Node B and Wet Lab Box plans (Central Node plan done 2026-11-09). *Documents: Electronics plan 5.1 (done); the three box plans.*

519. The USB hub box as built (Mike's photos, 2026-11-04). Mike's answers the same day settle (a), (e), (f) and (g). Mike built the hub box on 2026-10-22 and has installed it. Where the photos and the guides differ, the build stands; fix the guides at the next write-in. (a) The box: a TICONN IP67 box with a clear hinged lid, two steel latches and a grid mounting plate, standing upright with the lid facing out. Size about 12 x 8 x 5 in, inferred (Mike, 2026-11-04: "idunno, look on order history"). The order history gives no size for it. It is most likely one of the three TICONN boxes of the 2026-08-16 order, two of which Reference/Box Parts Order List v9.5.xlsx lists as about 12 x 8 x 5 in, for the aft junction and the transom terminal box, both since dropped. Scaled off the StarTech hub in the photo (7.8 in (198 mm) long, RS Components listing), it is about 10 x 7 in inside, which fits. (b) Glands: three, all on one side wall: two large split glands with a small gland between them. None on the top or bottom wall, so the no-holes-on-top rule (item 479) is already met and nothing moves. Which cable takes which gland is not logged. A1a, the drawing and the box plan show split gland S and PG7 T on a side wall plus split gland B and a PG9 on the bottom wall: change them to match. (c) The wing Cat6 looks to land straight on the Waveshare reader's screw terminals (its orange and green pairs are seen there), with no TB2 strip between, as the wiring review's (y) asked (item 482). Claude's reading of the photo; Mike's word settles it. (d) The AIS coax leaves the box through the lower split gland with a UHF plug on its outside end, so its joint to the antenna lead sits outside the box, not inside as A1a says (Claude's reading of the photo). Claude's suggestion: wrap that joint in self-amalgamating tape once it is made, since a UHF joint is not sealed. (e) The hub runs on Pi A's 5 V (Mike, 2026-11-04: "pi a 5"), as the guides say, so it still restarts whenever WD-A cycles Pi A. As built, the lead ends in a DC barrel plug in the hub's barrel socket, not on its green terminal (both take 5 to 24 V), and it enters by one of the three glands, not a PG7 of its own. The lead is 16 AWG (item 500 (j)). A ready-made barrel plug lead is usually 20 to 22 AWG (Claude's general knowledge, not checked for this one), so keep the thin part to the last few inches at the plug and run 16 AWG the rest. (f) DECIDED 2026-11-04 (Mike: "ok"): Pi B's wing link taps into the wing CAN pair at the wing box, not at the hub box, so nothing is drilled in the installed hub box. The wing box (not bought yet) takes a sixth gland (item 500 (m)). Pi B's adapter's 120 ohm switch off (its run is a branch); the hub box adapter's stays on (inferred). Settles item 498 (h). (g) DECIDED 2026-11-04 (Mike: "its already in there"): the hub box keeps its 12 V converter as built, and the wiring review's (p) (item 482) is dropped. *Documents: Electronics plan A1a, A2 entry 4, A17 and sec 3 box table; Wing Power System 8.7; Wing Trim Actuator Installation Guide sec 3; USB Hub Box Wiring 2026-10-20; Box Wiring Sheet A1a; Box_Plans_v10_4a/USB Hub Box v10.4a.pdf and the wing box plan; the order tracker's hub box row (updated 2026-11-04).* At v10.5: Written into the v10.5 guides. Still open: which cable takes which hub box gland, and Mike's word on where the wing Cat6 lands.

517. Change plans for the two battery boards, from Mike's photos (Mike, 2026-11-03: "Can you make plans that describe modifications needed to the battery bus and the backup battery bus boards."). Made 2026-11-03: Box_Plans_v10_4a/Main Bus Board Changes v10.4a.pdf and Box_Plans_v10_4a/Backup Battery Board Changes v10.4a.pdf (3 pages each: the photo with numbered marks; the wiring diagram after the changes, added 2026-11-03 at Mike's ask, "can you add wiring detail image?"; then every new or moved wire, the order of work and the parts; source _v104a_work/box_plans/changes/make_board_changes.py; photos Reference/Main Bus Board Photo 2026-11-03.jpg and Reference/Backup Battery Board Photo 2026-11-03.jpg). They draw what the guides already decided (Electronics plan 7.6 and A10; items 487, 489, 490, 501 (e) and (f)); nothing new is decided except Claude's picks below. Seen in the photos: both shunts are still on the minus side (item 487 still to do); all 15 breakers on the main board read right by their base colors against the 7.6 table (CAN, House CAN, Iridium A, bilge 1, bilge 2, USB and Wing clear 5 A; Pi A and Orion 10 A; Central and Wet lab 15 A; Steering and Aft 20 A; both releases 30 A); the backup battery board is built in a different arrangement from Backup Battery Board Layout 2026-10-15 and the Backup Battery Board plan (ANL at the top, + bar under it, the two chargers down the right side, the - bar at the bottom), so the change plan follows the board as built and the earlier layout drawings are out of date for it; the backup board has two 5 A breakers so far, and the Orion-Tr's input and remote are not yet wired. Claude's picks (standing unless Mike says otherwise): (a) the backup converter's input protection, open in Electronics plan 7.6 and A10, is a 20 A auto-reset stud breaker, a spare BFXM 20 A from the Sep 7 order (four bought, two used: Steering and Switch), on the backup board's + bar, with a short 12 AWG pair to the converter beside the battery: the converter draws about 15 A in at a rudder move and about 19 A at its full 17 A out from a Dyness near its 30 percent cutoff (computed, 88 percent efficiency), and 20 A protects the 12 AWG; (b) the Argodiode's jumpers are 6 AWG (the Kenhihi red and black on hand), 1/4 in lugs for its M6 studs (retailer listings; 4.7 x 2.4 in, 3 in tall); (c) the backup-fed bar pair is the second set of the two 150 A bar sets bought Oct 15 (inferred spare: one set is on the backup board); (d) bilge 2's breaker sits below the backup board's two breakers, the converter's breaker to their left; the two there now are labelled Pi B (left) and Iridium B (right); (e) the Orion-Tr's two main-battery pairs (input and on/off) come in at the backup board's top edge straight to the Orion-Tr's terminals, not bundled with any backup wire, each tagged MAIN BATTERY, in place of the marked left strip the earlier layout drew (the plan first drew a marked lane; Mike, 2026-11-08: "what is main battery lane? Why a large area on image?"; redrawn as the two wires); (f) if the pack - cable will not reach the - 400 A bar once the 300 A shunt is out, a new 2 AWG black from the roll on hand. Both boards are built and mounted in the boat (Mike, 2026-11-03: "Those are both created and mounted inside the boat right now"), so every change is done in place: on the main board, lift one end of the 300 A Class T at the battery box before the shunt work, since with only the battery switch off the incoming 2 AWG and the switch's input stud stay live beside it, and close it last; new parts go on with screws no longer than the board is thick. At the next write-in: Electronics plan 7.6 and A10 (the converter breaker, the jumper size, the backup board as built), BOM 15.4 (the bar pair and jumper, now priced at $0 on hand); redraw Backup Battery Board Layout 2026-10-15 and the Backup Battery Board plan from the photo. *Documents: Electronics plan 7.6, A10; BOM 15.4; Reference/Main Bus Board Drawing 2026-10-06; Backup Battery Board Layout 2026-10-15; Backup Battery Board plan.* At v10.5: The board work is written into the v10.5 guides (Electronics plan 7.6 and A10, BOM 15.4). Still open: redraw Backup Battery Board Layout 2026-10-15 and the Backup Battery Board plan from the photo. 2026-11-09: Box Plans v10.5/Backup Battery Board v10.5.pdf is redrawn as built from the photo with the changes drawn in (parts still to fit outlined green); this settles the redraw. Claude's picks: the screws for the new wires among the free ones. Found: the board stands 16 in tall and 12 in wide in the photo (the guides give 16 x 12 in, not which way up); each bar has 10 screws (the old plan said 6 studs); a PV surge module is already on the board, while the order tracker's Buy list still has a sixth to buy (check before buying).

509. The SBMS0's blank screen was the short ribbon fed backward; both SBMS0s work (Mike, 2026-11-02: "Bms nothing on screen", then "pin 1 was stripe, made it backwards and both old and new bms work"). The new SBMS0 showed nothing with 25 V between ribbon pins 1 and 12. The short store-bought 12-pin ribbon from the SBMS0 to the Winford board marks pin 1 with its stripe, where Electrodacus's own ribbon marks pin 12 in red (Reference/SBMS0 v03d Manual.pdf page 5), so it was fed with pack plus and minus swapped. Turned around, both the new SBMS0 and the first one (item 469, thought bricked) light up. The keyed plug does not prevent this: a ribbon fits one way at each end and can still be crossed inside. Write into Battery Box guide Part 8 ("Inside the watchman box") at the next write-in: the short ribbon runs pin 1 to pin 1, its stripe on terminal 1 of the Winford board; with both plugs keyed the same way, its stripe sits on the opposite edge from the factory ribbon's red wire; meter pin 1 to pin 12 at the SBMS0 end of the short ribbon, black lead on pin 1, before plugging in: plus about 26 V, never a minus sign. Same note on Reference/BMS and Balancer Wiring Sheet 2026-10-03 and the BMS box plan. Order tracker Parts row updated 2026-11-02. Mike, 2026-11-08: "both work and installed", then "Both tested, one on boat". Shunt sense run as built (Mike's photo, 2026-11-08): a 4-core 20 AWG cable (black, red, yellow, white) from the shunts lands on the top of terminals 1 to 4 of a six-block DIN strip, and the Cat6 cores to the SBMS0 green plug on the bottom (white-orange, orange, white-brown, brown), so terminals 1 to 4 = SBMS0 pins 1 to 4 (Claude's reading of the photo). At the shunts: solar shunt, red to the solar-bar side small screw (PVp), black to the bus side (PVn); battery shunt, white to the battery-switch side (ADC1p), yellow to the bus side (ADC1n); a 30 AWG link at the shunt end of each; tag the black core as +26 V. Terminals 5 and 6 are the XT1 thermistor: 12-core white to green (pin 15), the 11th color (tan) to blue (pin 16); the Cat6 cores to the plug are white (pin 1), orange (2), tan (3), brown (4) (Mike's notes on the BMS box plan, 2026-11-08). The guides call for Cat6 twisted pairs the whole way: write the as-built strip and colors into Battery Box guide Part 8 and Electronics plan 7.6 at the next write-in. No 30 AWG links on the shunt sense wires (Mike, 2026-11-08: "30awg would not last at sea on the battery board, too much shaking"). Mike then offered the 22 gauge at the DIN rail as the fuse; Claude: no, the fuse has to sit at the shunt end, where the current comes from: a short in the cable between the shunt and the box is fed straight from the shunt, and the thin wire at the DIN rail is past it. Claude's pick, asked 2026-11-08: a sealed inline mini blade fuse holder with a 1 A fuse at each of the four shunt screws, tied to the board (VANTRONIK 16 AWG 10-pack, Amazon B07MQZ9Q8L; Bussmann ATM-1 1 A, Amazon B00PYOYO54; prices not checked). DECIDED (Mike, 2026-11-08: "yes no fuses on shunt wires"): no fuse of any kind on the four shunt sense wires. At the shunts they sit only beside each other and the + leads, all within millivolts, so a rub there shorts nothing; the 4-core cable stays clear of the bus board's minus bars and is tied away from the SBMS0's USB plug in the watchman box (the USB shell is Pi A's unfused minus). Not bought: the inline holders and 1 A fuses. Still asked: the 18 battery tap links (a sturdier fuse than 30 AWG, or none). Battery box as built (Mike's photos, 2026-11-08): every tap wire goes straight to an insulated ring on its bus bar nut, with no fuse link; the wires run tied to the blue PEX rod sleeves, not in split loom; the XT1 probe end was lying loose on a cell top, not yet trapped against a cell face. DECIDED (Mike, 2026-11-08: "I think adding 18 fuses and connections on top of the batteries increases risk"; Claude agreed): no fuse of any kind on the 18 battery tap wires. The guides' 30 AWG links are dropped everywhere (taps and shunt sense wires); the 30 AWG wire is off the order tracker's Buy list. Instead: split loom on any tap wire where it crosses a bus bar or stud of another voltage, and every wire tied so it cannot rub. At the next write-in: Battery Box guide Part 8 (taps and shunt pairs: no fuse link), Glossary (fuse link entry), Wire and Cable Buy List E4 (drop), BOM 15.12 (the links), Electronics plan 7.6, Box Wiring Sheets A9, Reference/BMS and Balancer Wiring Sheet 2026-10-03, the BMS and Battery Box box plans; item 500 (n) is moot. One-page boat sheet made 2026-11-08 (Mike: "One printable page for bms programming and shunt wires"): Box_Plans_v10_4a/SBMS0 Setup and Shunt Wires v10.4a.pdf (source _v104a_work/box_plans/sbms0_setup/): the shunt wiring as built, the SBMS0 touch-screen settings in order, the first power-up signs. The shunt values go in the Automation menu's ADC settings (Claude's reading of manual page 38). SBMS0 serial speed 115,200 (Mike, 2026-11-08: "yes 115200"), settles item 401 (c): Device Settings, UART on, 115,200; write into System Settings Sheet sec 1 and Battery Box guide setup step 5 at the next write-in. *Documents: Battery Box Building Guide Part 8; BMS and Balancer Wiring Sheet; BMS box plan; order tracker.* At v10.5: The ribbon, the as-built shunt run, no fuses on the tap and sense wires and the serial speed are written into the v10.5 guides. Still open: the same on Reference/BMS and Balancer Wiring Sheet 2026-10-03 and the BMS and Battery Box plans.

502. Nuts on the half-inch bulkhead angle bolts: the 316 jam nuts on hand (Mike, 2026-11-02: "They already have jam nuts (as you can see were ordered). Is that good enough?"; Claude: yes). The 34 1/2-13 316 bolts that hold the stainless angles to the pylon bulkheads (24 at 2-1/2 in through the front and back angles, bulkhead and doubler; 10 at 3-1/2 in through both middle angles and the tripled middle bulkhead) each take one 316 hex nut and one 316 jam nut, from the 50 nuts and 35 jam nuts bought 2026-09-30 (Bolt Depot 2630993). No nylon lock nuts (Claude had first leaned to them: they stand about 0.6 in against 3/4 in for nut plus jam nut, so they fit the bolts better; not worth a new order). Nothing to buy. Fit, figured from the stacks, not measured (the glass on the bulkhead faces is not in the docs): on the 2-1/2 in bolts the jam nut ends flush to about two threads short; on the 3-1/2 in middle bolts, with no washers (as installed, below), flush or better. Accepted, the same rule as the main bolts (Design Decisions R-3.3A: "a jam nut short a thread or two is accepted"). These bolts carry the load sideways through the wood, so the jam nut only has to keep the nut from walking off as the plywood settles. How (Mike, 2026-11-02: "We don't want them to ever come off, then skip the anti-sieze goo?"; Claude: yes): blue Loctite on the threads, no Tef-Gel. These bolts touch only stainless and wood (no aluminum) and never come off, so Tef-Gel has no job there, and grease would stop the Loctite setting; the wet Loctite greases the threads while tightening, which keeps 316 on 316 from seizing. Turn slowly by hand, no impact driver. Run the nut down snug, then hold it with one wrench and turn the jam nut hard against it with a second, both before the Loctite sets. Tef-Gel stays everywhere stainless touches aluminum, and on the main bolts, whose nuts come off to fold. Front and back angles: head on the angle side, nut and washer on the wood face (the head must stay inside the angle, where the edge bolt nuts clear it). The 3/8 in edge bolts have room for no second nut (about 1/8 in shows past the nut): one 316 nut with blue Loctite. Already installed (Mike, 2026-11-02: "3/8 have blue loktite", then "kinda late since they are already installed"); not known whether all 36 are in or only the 30 on hand (if all 36, the tracker's buy line for six more is done). Write into Rig Base sec 5 as built: edge bolt nuts held with blue Loctite. The 10 middle bolts are already installed, with no washers and with blue Loctite (Mike, 2026-11-02: "10 middle bulkhead bolts are in without washer, with loktite"); head and nut bear on the stainless angles, so no washer is needed. Why no impact driver (Mike asked): it is the stainless, not the Loctite. A 316 nut spun fast and hammered on a 316 bolt heats the threads and can seize (gall) partway down, before it is tight; the Loctite slicks the threads but does not remove that. A nut that ran down and tightened normally did not gall, so bolts already in are fine. Write into Rig Base Two Plate Design sec 5 and the notes on Reference/Stainless Angle Holes 2026-10-19 and Reference/Middle Angle Bolt Holes 2026-10-12 (which still says a washer each side) at the next write-in. At v10.5: Written into Rig Base sec 5. Still open: the notes on the two angle drawings (no washers, blue thread locker), and whether all 36 edge bolts are in.

500. Box plans cross-check: small fixes, nothing to decide (Claude, 2026-11-01). Found while drawing the 16 box plans and checking every cable end to end (Box_Plans_v10_4a/Box Plans Cross Check v10.4a, page 2). Both ends of all 21 box-to-box cables agree, every entry matches Appendix A, every bus line lands. Fix at the next write-in. (a) Take the 120 ohm resistor off each SN65HVD230 CAN board (central node, Release Node B, wet lab box): the molded end plugs are the only terminators (Electronics plan 5.1); no guide says so. (b) The AEDIKO watchdog relays: if a board has a trigger jumper, set it so a dead Nano leaves the coil off and the Pi on (Compute Bay 4.3); the HiLetgo boards' setting is still not written (item 468 (ee)). (c) The alive line's optocoupler is at Pi B only (A2 entry 5, Compute Bay 4.2); A1 entry 6 and Sheet A1 also put one in the Pi A box. (d) The G2 drive's fault output is open-drain and needs a pull-up, not the pull-down the central node puts under the expander's screws. (e) The 600 W MOS boards' DC+ is fed from the release bus (they carry a regulator and an opto); Compute Bay 10.3 does not say so. (f) The DO sensor's FTDI RS-485 cable puts 5 V on its red wire: cut back and tape its red, brown and green at the wet lab box. (g) The Smart BatteryProtect needs its own ground wire to the battery minus on a 300 mA fuse (Victron manual 3.1); no guide, drawing or BOM line has it. (h) Stale Open lines: A3 entry 9 (Bilge_Pump_Wiring now shows pump 2 on the backup battery) and A10 (the board drawing now shows pump 2, the BatteryProtect and the converter fuse). (i) Box Wiring Sheet A14 still puts line 14 on the branch bar. (j) The Pi A and Pi B carriers take 5 V on a USB-C socket; no guide names the lead to it. The hub's 5 V lead from Pi A has no cable named and about 0.1 V to spare: 16 AWG, not 22 (inferred). (k) No pin map for Release Node B's five pins, no channel order for the four pullers (ch 3 to 6), no expander pin order: the plans draw Claude's picks, marked. (l) Release Node B's fire pair cable is not named; a 12 or 14 AWG pair may not fit its PG7. (m) The wing box needs a sixth hole if Pi B's CAN drop joins the wing link there (item 498 (h)); Appendix A's totals still leave the wing box's five glands uncounted (four PG9, one PG7 in the plan). (n) The 30 AWG copper for the 22 fuse links (18 taps, 4 shunt leads) was never bought; Wire List E4 says nothing to buy, and BOM 15.12 prices nine links. (o) Battery box: one 20-pack of cell bus bars against about 54 links, and their 72 mm hole spacing against a 73 mm pitch with mica (inferred); the main glands may break into the lid inserts; how XT1's lead joins the 12-core is not written; Sheet A9 says 22 to 18 AWG splices where the guide says 22 to 16. (p) Conformal coat: the Compute Bay Plan coats every board, the tracker struck it (Sep 26). (q) Compute Bay 8.2 says the Pi B box has 8 entries; Electronics plan A2 lists nine. (r) Iridium to Pi Wiring 2026-10-15 still says one USB isolator to buy (two were bought Oct 16) and shows the coax leaving the top wall. (s) The backup battery board drawing's own note says only the main battery wires leave by the left edge, but it draws the converter's 12/2 leaving there too. (t) Order tracker: the central node row still has 13 fuses with a ch 12 5 A fuse (12 now; holders 17 boat wide); the Winford boards' row carries the Thomson MD's UPS number; the network switch box row links to the hydrophone gland; the DDR-60L-5 and the USB isolators still read on the way. *Documents: Electronics plan 4.1, 5.1, 5.6, A1, A2, A3, A10, A15, A17, A18 and the totals; Compute Bay 4.1 to 4.3, 8.2, 10.3, 3.2; Wire List E4; BOM 15.4, 15.12; Battery Box guide Part 8; Box Wiring Sheets A1, A9, A14; Iridium to Pi Wiring 2026-10-15; Backup Battery Board Layout 2026-10-15; the order tracker.* At v10.5: (b), (d), (e), (f), (h), (i), (m), (q) and the hub lead in (j) are written into the v10.5 guides; (g) and (n) are moot (no BatteryProtect, no fuse links). (a) is settled by item 538 (snipped off). Still open: (c) where the alive line's optocoupler sits; (j) the lead to the Pi carriers' USB-C sockets; (k), (l) the Release Node B pin map and its release cable; (o), (p), (r), (s), (t).

487. Main bus board as built: both shunts are on the minus side (Mike's photos, 2026-10-31, "How to fix bus board?"). The photos show the 300 A battery shunt in the main negative, between the pack - cable and the - 400 A bar, and the 100 A solar shunt between the - solar bar and the - 400 A bar. Every doc puts both on the plus side (Battery Box Part 8, Electronics plan 7.6, Reference/Main Bus Board Drawing 2026-10-06), because the SBMS0 reads a shunt only with 4 to 76 V on it; Electrodacus's own manual says the battery shunt "gets connected to Battery+ terminal on one side then on the other side to a fuse or circuit breaker and your Load and chargers" (Reference/SBMS0 v03d Manual.pdf, step 4). On the minus side the battery percentage and the solar reading would be dead. The fix (decided by the docs; nothing for Mike to choose): battery switch, then the 300 A shunt, then the + 400 A bar stud D; + solar bar, then the 100 A shunt, then the + 400 A bar stud A; the pack - cable straight to the - 400 A bar stud 4; one plain 6 AWG from the - solar bar to the - 400 A bar stud 1. New short red links: one 2 AWG and one 6 AWG, two lugs each (four 2 AWG lugs are on the tracker with no job named); the black links freed on the minus side are spares. Sense pairs as in Battery Box Part 8 (battery-side screw brown to pin 4, bus side white-brown to pin 3; solar side orange to pin 2, bus side white-orange to pin 1; a 30 AWG fuse link at the shunt end of each), and a cover on each shunt: they are live now. Battery switch off and no PV connected while working. Also from the photos: (a) the five solar fuses sit at the + solar bar, as Electronics plan 7.6 says: the board is right and only the drawing is wrong (item 484 (a)); (b) the long jumpers from the branch bar down to the bottom breakers (USB, bilge 1, Orion, wing, bilge 2) are well over 7 in: sleeve them in the split loom on hand (item 468 (z)); (c) the top breaker labelled CAN (control bus) comes off (item 486 (7)), and the one labelled Aft feeds only the network switch box now (relabel it Switch); (d) the yellow-wire strip and the 1k go on the board for the new charge stop (item 486 (6)). Docs written in 2026-11-01: Reference/Main Bus Board Drawing 2026-10-06 and its Layout redrawn (shunts on the + side with the check printed, fuses at the + solar bar with each controller on its own 14/2, line 1 off, line 6 labelled Switch, the charge-stop strip and 1k, the split-loom note, Pi A good to 22 ft), the before-first-power-up shunt check in Build Guide 11.1, Battery Box Part 8 and Electronics plan 7.6, and the order tracker's Do next list. Still to do: the board itself (Mike): move both shunts, pull the CAN breaker, loom the long jumpers, fit the strip and the 1k. Shunts moved to the + side (Mike, 2026-11-08: "Shunts moved"). Left: the CAN breaker, the jumper loom. Close this item when Mike says the board is done. At v10.5: Still open: the board work left (the CAN breaker off, the jumper loom). Mike's photo of 2026-11-10: both shunts now on the + side (battery switch, 300 A shunt, + 400 A bar; + solar bar, 100 A shunt, + 400 A bar) and nothing but plain cable on the − side; the CAN breaker's jumper is off. Still to do: covers on both shunts and the long jumpers in split loom (item 561).

450. VESC A box: the CXCESNS aluminum box, its floor as the cooling plate, and the motor leads re-lugged inside (Mike, 2026-10-24: "yes to both, buying the box today"). At v10.4: written in: the CXCESNS box, its floor as the cooling plate, no surge diode, the Flipsky held by four flat-head screws from outside into its own holes, its size from Flipsky's spec (5-1/8 x 2-11/16 in), the Pi A cable's landing. Still open: how the motor's three phase leads enter the box (three PG21 glands passing the lugs uncut, Claude's pick; PG16 glands with the leads re-lugged inside; or the joints outside), Mike's call once the motor is mounted (Mike, 2026-10-24: "will measure distance and decide after motor mounted"); and the Flipsky screws' thread (M3 or M4), read off the part. (a) The box is a CXCESNS cast aluminum box, 11.8 x 8.3 x 3.9 in, the same as Pi A, Pi B and the network switch box; Mike is buying it 2026-10-24 (Amazon, $65.99, $60.71 with the coupon). Replaces BOM 15.5's "VESC A waterproof enclosure, ON HAND" ($40 estimate, model never named). (b) The box floor is the cooling plate: the floor glues straight to the hull in the heat-carrying epoxy (Compute Bay 2.3), the way the switch box does (decided 2026-10-03), and the Flipsky bolts to four 316 flat-head studs set through the floor from outside in epoxy before gluing, heads flush, on the Minus Pad 8 gap pad; the posts sit on the same kind of stud. No separate plate and no board-size hole in the floor. Closes "Cooling plate size" (Part 1B). Heat: roughly 60 W at 2 kW (a guess at 97 percent), a few watts at the usual 150 to 250 W, through about 98 sq in of floor. The box stays wired to nothing (Lightning Guide 6.2): the Flipsky's metal base touches only the gap pad and the studs, and an aluminum-board base is insulated from its copper (inferred). A desiccant pack goes in, since the floor runs near sea temperature. (c) The motor's lugged phase leads cannot pass a PG16 (its seal takes 0.39 to 0.55 in cable; a heavy 3/8 in lug is about 3/4 in wide, a guess): cut each lug off, feed the lead in through its PG16, crimp a new 3/8 in lug inside, and bolt it face to face to an 8 AWG 3/8 in lug on the Flipsky's own lead of the same letter (U to U, V to V, W to W) with a 3/8-16 x 1 in 316 bolt, washers and a nyloc, glue-lined heat-shrink over each joint. Settles item 419 (d). To buy: three 3/8-16 x 1 in 316 bolts (none that length on hand), and three lugs for the motor lead if it is not 2 AWG (its size is printed on the jacket; not on record). Layout and gland plan, redrawn 2026-10-26 from Mike's photo of the parts in the box: the Flipsky is about 2.4 x 4.3 in with its battery leads out one end and its motor leads out the other (switch and sensor plugs on one side, CAN and USB on the other, servo and COMM at the motor end); the posts sit under the battery glands along one short wall, the capacitor bank and WAGOs beside the Flipsky under the + post; the box has a ledge with holes along each short wall and a boss low on each long side. Glands, all 1 in below the rim, with the box drawn lying long side left to right, battery end on the left and corners numbered 1 top-left, 2 top-right, 3 bottom-right, 4 bottom-left (sheet redone 2026-10-26 in the style of Mike's Pi A box sheet, at his request): + and − PG16 on the battery end, 2-3/8 and 5-7/8 in from corner 1; the three phase PG16s on the motor end, 2-1/2, 4-1/8 and 5-3/4 in from corner 2; C PG7 on the top side, 7-3/8 in from corner 1; S and U PG7s on the bottom side, 6-5/8 and 7-5/8 in from corner 4. The Flipsky's power button and its lead come out (the shorted plug replaces them); its USB lead stays coiled inside for VESC Tool with the lid off (Claude's pick). Flipsky size and holes (2026-10-26): the case is 130 x 68 mm (5-1/8 x 2-11/16 in, Flipsky's spec), not the 2.4 x 4.3 in read off the photo (the photo's camera sat close, so the deeper Flipsky looked small). Its four mounting holes are blind and threaded in its finned bottom plate, 40 x 120 mm (1-9/16 x 4-23/32 in), centered, read off Flipsky's own photo of the bottom (inferred; thread M3 or M4 is a guess); it has no ears. Full-size pattern: Flipsky Hole Pattern 2026-10-26 (.html master and .pdf). Hold-down (Mike, 2026-10-26: "holes"): four 316 flat-head screws from outside, up through the floor into the Flipsky's own holes, countersunk flush (90 degrees if metric), set before the box is glued to the hull; the Flipsky then stays in for good. Replaces the floor studs and nylocs for the Flipsky; the posts keep their studs. Motor lead entry (Mike, 2026-10-26): he decides once the motor is mounted and the distance known; the choices are three PG21 glands (1-1/8 in holes, seal 0.51 to 0.71 in) passing the motor's own lugs uncut (Claude's pick; glue-lined heat-shrink built up on the lead if it is under 0.51 in), the PG16 re-lug plan above, or the joints outside the box (Claude advises against: salt on bolted joints). Any motor lead may go to any Flipsky lead, one to one; the order only sets the direction, set in VESC Tool, but bolt all three before the motor setup wizard. Build guide (Pi A guide format, with the floor plan, hole map, wire list and gather checklist): VESC A Box Build Prep 2026-10-24.html (top of the folder); the two-page print, the floor plan with every hole and the notes, is VESC A Box Build Sheet 2026-10-26 (.html master and .pdf, Mike, 2026-10-26: the full guide printed 21 pages). Written in: VESC A Box Wiring 2026-10-14 (updated 2026-10-24; the leftover 1.0 in clamp drawing removed), order tracker (Parts row "VESC boxes", Buy list). To write in: Electronics plan A7 (box, cooling, motor leads), Build Guide 5.1 and 5.2 (the plate paragraph), Compute Bay 2.3 and 4.4 ("motor controller plate" becomes the VESC box floor), Lightning Guide 6.2, Design Decisions (the four hull-glued boxes), BOM 15.5 (the enclosure line and the three bolts), Box Wiring Sheet A7 notes, Wire and Cable Buy List A3 ("no joint in the 300 A path" becomes one bolted joint per phase). As built (Mike's photo, 2026-11-06; box plan page 2 redrawn to match, Mike: "yes"): the + and − PG16s and all three PG7s are on one long side (spots read off the photo: − 3-3/4, + 5, C 6-3/4, S 8-1/4, U 9-3/4 in from the battery end corner; which big gland is + is Claude's pick), the three motor glands are PG21 on the motor end, the posts are screwed down from inside (screw tips must sit flush under the floor), the − 12 AWG capacitor lead is red marked with black shrink, and the capacitors and WAGOs sit along the long side away from the glands, by the − post (Mike, 2026-11-06), so the + 12 AWG lead is about 5-1/4 in and the − one short, both under 6 in. DECIDED 2026-11-06 (Mike: "power take out and short plug, joints inside box"): the Flipsky's power button comes out and the crimped shorted plug (IGNITE joined to BAT+) goes in its switch socket; the motor's three leads come in through the three PG21 glands with their own lugs uncut and bolt to the Flipsky's U, V, W inside the box. This settles the motor lead entry above: the PG16 re-lug plan and the joints-outside choice are dropped, and no motor lead lugs are needed. Box plan updated to match. At v10.5: Written into the v10.5 guides (three PG21 glands, lugs uncut; the box as built). Still open: the Flipsky's mounting-hole thread (M3 or M4).

449. The BaroVUE 10 and HygroVUE 10 cables: each sensor's own Campbell cable runs whole into its hub box gland, nothing to buy (Claude, 2026-10-21, from Mike's "what kind of cable for baro and hydro vue?"). At v10.4: the BaroVUE 10's cable, hose and barb reducer are written in (Barometer guide, hub box). Still open: where the HygroVUE 10 mounts on deck and which radiation shield it gets. From the BaroVUE 10 manual (rev 04/2022, copy: Reference/Campbell BaroVUE10 Manual 2022-04.pdf): its cable plugs into a removable 5-pin screw plug on the sensor; maximum cable length 3 m (10 ft); supply 9 to 28 V; the pressure fitting is a 1/8 in barb. Campbell's replacement cable (BaroVUE10CBL) is 30 in (campbellsci.com). So the BaroVUE sits inside the hull within reach of its 30 in cable from the hub box's gland 2 (Claude's pick, standing unless Mike says otherwise); the hose from the Gill port does the long run, and a sensor beside the hub box is still above the hose's low point and drain (Barometer guide sec 4). This settles the "fitting to confirm" check in Barometer guide sec 1: a 1/8 in barb, sealed, so no sealed box; the 1/4 in ID hose needs a 1/4 to 1/8 in barb reducer at the sensor. The HygroVUE 10 ships with 5 m (16.4 ft) of cable (campbellsci.com product page); what length was ordered on Josh's account is not known. Its mounting spot is still open (Barometer guide sec 1); pick it within its cable's reach of the hub box, or join on screw terminals with the leftover 22/12 shielded (C1), which SDI-12 allows. *Documents: Barometer and Pressure Port secs 1 and 4; Electronics plan A1a; USB hub box drawing; BOM 15.11 (the barb reducer, pocket change); order tracker.*

442. The MOTU M2 sits in its own box, not in the USB hub box (Mike, 2026-10-20: "we already decided MOTO in its own box"); and the hub box wiring drawing. At v10.4: written in: the MOTU M2 is not in the USB hub box; the hub box drawing's layout. Still open: which box the MOTU M2 sits in. The USB hub box: a TICONN, about 12 x 8 x 5 in (inferred, item 519 (a)). The earlier decision was never written down: every guide still said "Open: where the MOTU M2 sits", so the first draft of the drawing put it inside the hub box. Now settled: the MOTU M2 has its own box; only its USB lead comes into the hub box, by port e of the Altelix 5-port split gland, to a hub port. Iridium A's USB cable no longer comes into the hub box at all (item 444). The MOTU's own box is not picked and not drawn. Drawing: USB Hub Box Wiring 2026-10-20 (.html master, .pdf to print; the v10.2 drawing of 2026-10-14 went to Archive): page 1 where the parts sit (not to scale, Mike: "don't need to scale"), page 2 the wiring, page 3 every wire from and to. New in it, Claude's layout, standing unless Mike says otherwise: (a) two DIN terminal strips on one short rail with the Waveshare reader: TB1 (24 V in, the YRDZXG's leads, 12 V and SDI-12 out) and TB2 (the wing cable: tip meter on 1 and 2, compass on 3 and 4, grounds on 5 to 7 bridged, CAN on 8 and 9); (b) the BaroVUE 10 and HygroVUE 10 each in their own PG7 gland, joined on TB1 (one cable per gland); wire colors from Campbell's manuals (BaroVUE red 12 V, black ground, white SDI-12, blue and yellow RS-232 cut and taped; HygroVUE brown 12 V, black ground, white SDI-12, clear shield to 0 V); (c) the Waveshare's channel 1 for the tip meter, channel 2 for the compass. Still open: the hub box itself (not picked; about 10 x 8 x 4 in or bigger). The surge diode mismatch with Box Parts With Photos 2026-10-15 is settled by item 446 (the diode goes in). *Documents: Electronics plan A1a (MOTU line and its "Open", the second split gland, the glands list); Box Wiring Sheet A1a (same); Science Payload Strategy and Compute Bay 4.4 (where the MOTU sits); Box Parts With Photos.*

400. Order tracker rows still to settle (2026-10-08; brought up to date 2026-10-19). The BOM's status words are up to the tracker at v10.3. Still open: the Waveshare 7-port marked ordered Oct 7 has no order mail (cancel it if it was placed); the fuse links row prices nine, against 18 tap links plus 4 at the shunts; Reference/Left To Buy 2026-09-26 still says about $4,580; the tracker's puller fuse holder row links B0DSW8RTTP, the cancelled UK5 6-pack's listing, while the holder bought is Amazon order 114-6285250-6767424 (listing not logged). *Documents: the order tracker; Left to Buy; BOM 15.4, 15.7.*

384. Lewmar hatch: one check left. The Lewmar Medium Profile size 60 is written in at v10.2 (Build Guide 3.2, 4.4, 11.2; Design Decisions R-3.2; BOM 15.2). Its cut-out is 20 x 20 in, where the guides sized the opening at 24 x 30 in: check nothing that must come out at refit is bigger than 20 in square (Open line, Build Guide 3.2). Its weight is not known, so the Design Decisions R-1.3 weight table still carries the cover's 18 lb. Of the 30 3/8-16 x 2 in hatch bolts on hand, twelve are rig base edge bolts (Mike, 2026-10-12); the other eighteen are the rig base's outer-angle edge bolts too, with six more to buy (settled 2026-10-19, item 439 (l)). *Documents: Build Guide 3.2; Design Decisions R-1.3.*

8a. Drawings for shapes already decided. The wing can's drawings are on the welder's sheet (item 343); the 2026-09-24 concept drawing went to Archive 2026-10-08 (it still showed a base ring and a can-wall bolt). Its old blanks: the pipe cut length (the Spec Sheet formula should take off 1/4 in, not the whole 3/4 in lip, because the lip slips over the pipe; inferred from the drawing, check before cutting) and the labyrinth edge. Still stale: Rev H wing sheets 2 and 6 (the Wing Trim guide no longer points to them; the pipe cut-length note is in the Spec Sheet since v10.0). *Documents: the wing drawing set, Wing Can Spec Sheet.*

276. Cord puller mount: Mike is making a new mount (2026-09-26), neither of the two drawn. Log its shape, how it is fixed and where the hull hole goes once it is made (Open line in Transom Drogue Box Guide 6 and Design Decisions R-3.6C). The motor screws are written in at v10.2 (M4 pan-head 316 with flat washers, 11/64 in holes, no countersink, blue thread locker); the tracker shows only black 304 M4 x 10 mm screws and an alloy kit, so check the shelf for 316 pan-heads before the motors go on. *Documents: Transom Drogue Box Guide 6, Build Guide 7.3, Reference/Cord Puller Mount 2026-09-24.md.*

335. Motor mount: what is left (written into Build Guide 3.5 at v10.1). 2026-10-20 (Motor mount supplies chat): Claude's pick for the face plate, aluminum 6061-T6, 3/8 in thick (about 20 x 10 in, T shape) with 1/4 in feet, cut by SendCutSend; Mike's yes is still owed. v10.1 carries the measured shaft (8-3/8 in, so the L-110 and the Lasdrop fit), the face plate with two feet, the plywood trial fit (Reference/Motor Mount Trial Fit Guide 2026-09-30), the L-110 figures and the M16 x 1.5 coolant ports. Still open: (a) Mike's trial fit measurements (A to G), then Claude draws the cut file; (b) the plate metal, aluminum or stainless, and the V-block's material (3/4 in okoume with a cast epoxy V is where Mike's notes leaned); (c) the height check before drawing metal: the notes' numbers say the beds rise above the shaft toward the front, so rails set from the back would run into the bed at the front; the straight bar clamped on the shaft settles it, and the stack must count the rubber under the foot; (d) the coolant barbs: moot, the loop is dropped and the ports plugged (item 466, 2026-10-29); (e) the idea in Mike's handoff notes of a pillow block bridge (ledges glassed to the valley walls, a bar across, the block on a rubber pad) is in no guide; Mike to say if it stays. Also at the shaft: the keyway (a machine shop cuts one if none), straight or tapered end, and the cracked bed near its aft end (open, probe, fill before the rail goes on). *Documents: Build Guide 3.5, BOM 15.5, Design Decisions R-3.5G.*

346. Longer prop shaft: ordered (Mike, 2026-10-01), what is left. The 31 in shaft is written into Build Guide 3.5 and 5.1, BOM 15.5 and Design Decisions R-3.5, and is on the order tracker as ordered; seller, price and due date not logged. At the first fit, check the prop hub clears the rudder's front edge with the rudder hard over each way. Claude's opinion, Mike's call: put the pillow block just behind the Lovejoy, not right behind the seal, so the shaft hangs as little as possible past its last bearing. *Documents: Build Guide 3.5; BOM 15.5.*

352 and 353. What is left of the two mismatch lists of 2026-10-02 (after v10.2). v10.2 settles most of them; these are still open, each needing a decision or a look: (a) decided 2026-11-07 by item 526: no inline fuse in either release feeder; (b) settled and checked at v10.3 (Pi B on the backup battery board's 5 A breaker, no fuse in its box; no hub box fuse); (c) Pi B's wall: entry 9 is a metal SMA bulkhead, against "nothing conductive touches the wall" (Compute Bay 7.3); (d) the battery trip "isolates the bank", but Electronics plan 7.6 has no contactor or disconnect besides the manual switch: what does the isolating is not written; (e) the release bus readback: Compute Bay 10.2 and 11 give an expander pin to it, the Build Guide says no release-bus readback, and Electronics plan 4.1 has the opto board read only the Water Witch states; (f) WD-B "puts the full data on the bus" (Compute Bay 13.1), but WD-B has no bus link (likely fix: WD-B hands the strike log to Pi B over its serial line); (g) the hub box and wing box bar studs: the v10.0super closed list says the branch bar's end stud, the Electronics plan 7.6 table and the 2026-10-06 drawing say studs 8 and 3 (Open lines in A1a and A17; Mike's word on the table closes both); (h) how Starlink's Cat6 and power pair plug into the Mini, and its power wire, 14/2 in Wire List A8 against one of the 16/2 runs in C2; (i) where the HygroVUE mounts and the RockBLOCK's serial logic level. *Documents: Compute Bay 4.2, 7.3, 10.2, 10.3, 11, 13.1; Electronics plan 4.1, 7.6, A1a, A10, A15, A17; Wire and Cable Buy List A8, C2; BOM 15.4.* At v10.5: (a) is written in: no inline fuse in either release feeder.

436. Left over from the v10.2a write-in (Claude, 2026-10-18). Each is an Open line in the guides or a mismatch the write-in found. (a) The 5 V surge diode on the lightning detector lead: not picked (Compute Bay, Electronics plan A12, BOM). (b) The software must accept signed commands over Starlink as well as Iridium; the Starlink rules count on it (Build Guide sec 8, System Settings Sheet). (c) Iridium A's USB cable goes into the USB hub, so a dead hub also cuts Iridium A, and no guide says the hub stays on in safe mode: needs a line in Compute Bay and the Electronics plan once settled (Claude's view: Iridium A into one of Pi A's own two ports would avoid it, but both carry the hub and the CAN adapter). (d) The two split gland choices for the Iridium cables (Electronics plan A2 and A1a). (e) and (f) settled and written in at v10.3. (g) The dated wet lab box drawing (Wet Lab Box Layout 2026-10-15) still shows a vent and puts the surge diode where Reference/Wet Lab Box 2026-10-14 does not. (h) Mismatches found, not settled: Build Guide puts Primelink B on the emergency bank, sec 4.3 and the Electronics plan do not; Electronics plan A3 entry 22 may break one cable per gland; the UV-C boards are $14.80 in the BOM and $37.10 on the tracker. Detail: Archive/_v102a_work/reports/A.md to F.md. *Documents: as named.*

438. Left over from the v10.3 write-in (Claude, 2026-10-19). (a) The slip ring brush bracket cannot be short: the post's top is about 10 to 11 in below the mast plate and the brush rides the 3 in of drive tube just under the drive bar, about 7 to 10 in above the post's top, so a bar from the post's side must climb past the ring's tabs and the 6 in drip cup and come back in to the tube: about a 10 in stick-out arm of 1/4 x 1 in bar, which may flex under the brush's spring (Claude's figures from the heights in Wing Power System 1A; the brush also sits 3 to 6 in above the hand-holes' top edge). Its length, bend and thickness go on the can's build drawing (Open line in the Wing Can Spec Sheet). (b) Settled at the v10.3 check: the wing box's 5 A fuse is on the box's short DIN rail in every guide. (c) Settled (Mike, 2026-10-19, "yes"): the wing counts in the daily total; see the Closed at v10.3 list. (d) Settled at the v10.3 check. Detail: _v103_work/reports/A.md to D.md. *Documents: as named.*

439. Left over from the v10.3 accuracy check (Claude, 2026-10-19). The check fixed about 290 mismatches in the guides; these need a number, a look or a measurement first. (a) The always-on network switch draws about 72 Wh a day (Electronics plan 6.1), but the Build Guide 4.6 hotel table has no line for it, and nothing says the 160 Wh "Pi CM5 + sensors" line holds it; if it is outside, the hotel load is about 915 Wh a day, not 845, and secs 4.6 and 4.7 move. Finding where the 160 came from settles it. (b) Build Guide 4.4's panel stations are shorter than the panels: the stern station is 60 in for a 62.2 in panel, and the middle station 67.2 in for three 24.1 in panels crosswise; from the pylon flanks to the post the panels fill the run butted end to end, with no gap for the edge fillets. Re-lay the stations from the panel sizes with the four deck checks already open for 4.4. Reference/Deck Solar Panels and Mounting 2026-09-26 also says "16 panels" against its own list of 14. (c) Build Guide 5.3 gives 850 to 900 rpm and 4.16 kt at 2 kW, but Design Decisions R-3.5D and the prop pitch study say the motor runs out of voltage near 900 rpm on the 25.6 V bus, where the 12 x 10 prop takes about 1,720 W; the lake power sweep (Build Guide 11.2) settles the 2 kW rows and the lee-shore figures. (d) Build Guide 1.4 and Design Decisions R-1.4 say the conversion costs about 0.12 to 0.14 kt, but the per-100 lb rate they give puts the added weight at about 0.18 to 0.35 kt: say which weight the figure is for and re-figure. (e) Design Decisions R-1.3's drogue row says 95 lb but its parts add to 99; recount it from the parts as built (the R-1.3 totals and Build Guide 1.3 move with it). (f) Compute Bay 5.3's backup island rows do not multiply out: Pi B at 3 to 3.5 W for 8 percent of a day is about 6 to 7 Wh, not 10 to 15, and the rows add to about 23 to 31, not 25 to 32; the working behind them settles it. (g) Build Guide 3.1 counts the three pylon bulkheads among the watertight ones; supported from the keel area with okoume, they may not close off the hull past the battery box; the bulkhead drawing of 2026-09-15 settles it. (h) A third shaft collar anode came with the Piranha cutter (order tracker; same parcel, no delivery mail): when the parcel is found, the Build Guide 3.5 and Design Decisions R-3.5E anode counts follow the BOM. (i) The post's copper run is given as about 7 ft, two stock sticks (Lightning Guide 5.3 and 9.1, Instrument Post Guide 12.2, BOM 15.2), but by the guides' own stations it is about 11 to 14 ft (Claude's figure); add it to the bar-run measuring in the moved-out lightning questions, and do not cut to 7 ft. (j) Iridium chain A's arrestor lead: the deck stub and the post's deck terminal are about 2 ft or more apart, not a few inches (Open lines in Lightning Guide 7.1 and Instrument Post Guide 12.3); the post guide's own rule puts each arrestor at its own hull entry, so measure the lead at fit-out. Instrument Post Guide 11.1 also puts the deck terminal "aft of the boot", against "port side" in 12.2. (k) The horn on the post is not on the Lightning Guide's bonding list (sec 6.2); whether its body takes a spur depends on whether the maker ties the body to a 24 V lead. (l) Settled 2026-10-19 without a measurement: the stack through the outer angle's 1/4 in stainless leg is 1-1/2 in, so the 3/8-16 x 2 in bolts fit; all 36 edge bolts are that bolt, 30 on hand and 6 more to buy (Bolt Depot 16131, tracker Buy list); Rig Base sec 5, BOM 15.2. (m) Where the Starlink and GPS antenna mounts spur to the copper (Open line in Lightning Guide 6.2 item 9): none is on the post; pick the mounts first, and never spur GPS B's mount to the copper through its coax shield. (n) Wing trim's step on the load-shed ladder is not named (Open line in the Settings Sheet sec 4). (o) Boat 1 Route sec 2's Leg 1A motor levels and the Routing Guide's "a fast passage waits north up to about three weeks" still follow the 1,675 W array: fold them into the deck solar change rework (item 313). (p) Barometer and Pressure Port 3.4 figures the arm load at 32 in; the arm is at 44 in, which roughly makes its share about 13 percent of the post load (Claude's figure; the order of failure holds); re-run it at the real height (Open line there). (q) The post's 5 x 5 in head plate overhangs the 4 x 4 in tube by 1/2 in a side, and the air terminal stack on the port face is about 3/8 in thick, so a centered plate's edge meets the bar: draw how they clear. (r) The Trim Actuator Guide buys four rod-end clevises (two on the link, two for the pushrod ends); the order tracker's Buy list row has two; settle the count when the link and pushrod ends are drawn. (s) The Kamoer dosing pumps are still "arriving October 2 to 14" in the Science Payload Strategy and Wet Lab guides; the tracker has them on the way with no delivery mail: check the shelf. (t) Item 2's displacement range (5,570 to 5,775 lb) is a pound or two behind the Build Guide's 5,780 (secs 1.3, 6.9 and 11.2 now agree). *Documents: as named.*

478. Left over from the v10.4 write-in (Claude, 2026-10-31). Each was found by the write-in and left as it was, since no decision settles it. (a) Build Guide 5.3 modes table: "Sustained 750-1,500 W, indefinite" does not fit the sealed-jacket run times (about 1 kW all day except in the hottest sealed hull; 1 to 1.5 kW only after the 2 kW derate; Reference/Motor Dry Running 2026-10-29.md). (b) Design Decisions R-1.3 propulsion weight stays 110 lb, about 14 lb high now the loop is gone (a guess); reweigh at the next weight table. (c) Build Guide 6.9: the feather-confirm signal reads the flap position from the actuator's own sensor; with the give-way spring that is the horn's position, so confirm by the wing compass and tip wind meter too. (d) Build Guide 4.6: the nav lights' 30 Wh a day leave out the two converters' losses (small). (e) Bus top voltage: the Electronics plan A1a says 28.4 V, Lightning Guide 7.6 says 29.2 V (the Barometer guide no longer gives a figure, 2026-11-02); one figure from the System Settings Sheet. (f) Electronics plan A7: the VESC feed is 5 to 6 ft, about 10 ft on Reference/Main Bus Board Drawing 2026-10-06. (g) Split gland naming: "PG25" in the Electronics plan, the Box Wiring Sheets, BOM and Glossary; M30 thread with a 1-3/16 in (30 mm) hole on the hub box drawing. (h) Box Wiring Sheets A3 and A6 and several guides say "a dead node leaves the boat lit / the UV on": true for a dead Nucleo or expander while the node's feed is live, not for a lost feed (Compute Bay Plan sec 11 has it right). (i) The puller's 1N5408 flyback runs from the MOSFET drain to the release bus (Compute Bay 10.3, Transom guide sec 6); with the fuse now on the plus side, land it on the relay side of the fuse (inferred; both work). (j) Compute Bay 10.2: "all 16 expander pins used" counts to 15. (k) Trim Guide sec 8: the weekly full-stroke sweep runs past the 0.875 in soft limits; say whether the sweep stays inside them. (l) Wing Construction Guide sec 5's "about $2,600" leaves out the new PEX, hinge and hardware rows; Stage 10's "roughly 38 in" boom mass center is about 36 in (inferred). (m) The BOM's YRDZXG input range: 18 to 32 V in the BOM, 12 to 32 V on the listing (inferred); the BOM's camera port UV-C boards $14.80 against the tracker's $37.10; the BOM's past delivery dates (slip ring, wing compass, Lewmar hatch) to bring up to the tracker's On the way tab. (n) Box Wiring Sheet R1 has one hidden label still naming the transom terminal box. (o) Wire and Cable Buy List A8: the first 14/2 roll is spoken for and the backup battery board needs about 60 ft more; with the second roll held, a shortfall at fit-out is likely. (p) The Wing Power System 1A Rion arrival date (due about 2026-10-20) and the MOOKEERF return date (about 2026-10-08) are past; bring up to the tracker. (q) Wing Power System 8.5: no pair assignment for the wing Cat6 is written (the fourth pair unused, inferred). *Documents: as named.* At v10.5: (j) is closed: it was wrong (item 483 (h)).

480. Bilge pump wiring drawing (Claude, 2026-10-31, from Mike's "bilge pump wiring diagram"). New one-page sheet Bilge Pump Wiring 2026-10-31 (HTML and PDF, top level) draws both pumps from the guides as they stand: breaker, 16/2, Water Witch (red to + through the breaker, black to 0 V, tan to pump +, from the maker's 217/230/230-24 install sheet), the ch 6 and ch 12 manual-ons through the aft junction, and the two running signals back to the central node's opto board. Nothing decided changes. At the next write-in: (a) Build Guide 3.6 and Electronics plan A6 point to the sheet; (b) add to Build Guide 3.6 that a Water Witch runs its pump a few seconds each time its feed comes on (maker's sheet, Reference/Water Witch 217 230 230-24 Install Sheet.pdf), so the duty-cycle software ignores that run; (c) the bilge cable is drawn as the 18/4 decided in item 467 (j); pump 2's switch-on path is left open on the sheet, as in item 467 (k); (d) the joint part at each pump's + and 0 V (three wires each) is not set in any guide. At v10.5: (a) to (c) are written into the v10.5 guides. Still open: (d) the joint part at each pump's + and 0 V, and the drawing still shows the BatteryProtect, which is dropped.

1B. Jobs that produce a number, then a document update

515. The main side's always-on draw is likely well above the HIBERNATE 200 Wh a day (Claude, 2026-11-03, from Mike's "Can you list draw of everything"). Adding the loads that stay on with Starlink, science and the cameras off: Pi A and sensors 160, watchdog and housekeeping 24, steering 45, the wing 34, Iridium A 5, AIS listening 20, nav lights 30 (all Build Guide 4.6), the network switch box about 72 (item 489), and lines not in the 4.6 table: the central node 25 to 50 (a guess), the foredeck fisheye 120 to 190 if left on (4.6 Open line), and unknowns (VESC A idle, the five main solar chargers at night, the watchman and JK balancer, the house bus converter; a guess of 50 to 150 together). About 465 to 590 Wh a day with the fisheye off. So with the main solar dead the main bank (90 to 10 percent, about 25.8 kWh) lasts about 1.5 to 2 months, not the 4 months in item 489 and Build Guide 4.7 (HIBERNATE ~200). Pi A and the USB hub off (WD-A's relay, Compute Bay 4.3) would take off about 160. Settle: find VESC A's idle draw, the SmartSolar self-use, the SBMS0 and JK balancer draw, the TSW202's idle draw; then fix Build Guide 4.6 and 4.7.

511. Left over from the readability rewrite (Claude, 2026-11-02). Found by the rewriters; nothing below is decided. *Battery Box Building Guide:* (a) Shunt sense pairs: Part 8 (Mounting) runs both shunts' sense pairs through one PG9 on the watchman box, which keeps one cable to a gland only if both pairs ride in one jacket; Wire and Cable Buy List C7 says the battery box wall takes "three cables", one per gland, then lists four, the fourth being those sense pairs, which go to the watchman box, not through the battery box wall. Fix: C7 says where the sense pairs go, and Part 8 says they share one jacket or gives each its own gland (the hole list's home is the Electronics plan). (b) The Parts List's SBMS0 row still reads "direct from electrodacus.com, about $155", as if not yet bought; the Bill of Materials has the first board overheated and a new one ordered 2026-10-31. Fix: point the row to the Bill of Materials. *Bill of Materials:* (c) 15.2 lists eight 3/4-10 x 4 in main bolts and four 4-1/2 in (twelve, as the Rig Base guide has); the Bolt Depot order line lists ten 4 in. Say whether two are extra. (d) 15.2's plywood line still names a "pylon box"; the pylon support line says there is none. Fix: drop it. (e) 15.2: "Never 316 nuts: the bronze is meant to corrode first." The Rig Base guide (sec 3) gives the reason: bronze on stainless does not seize and tear the thread, and the nut is the part meant to wear. Fix: use that reason. (f) 15.13's services list has "welding the twelve rig-bolt heads to the rail"; there is no rail, the heads are spot welded to the head bars (Rig Base sec 5, Build the base, step 1). (g) 15.13's unpriced list still names the BaroVUE 10's barb reducer, dropped when the drying tube came in. Fix: drop it. (h) Drogue U-bolts: 15.7 has "two M12 316 bow-eye U-bolts, one per drogue"; the Transom Drogue Box Guide (sec 4A) has one per quarter, shared by both drogues. Fix: 15.7 to match the guide. (i) 15.7 and Transom sec 4A: "seller rating 3,500 lb; the 8,000 lb T8 is the fuse, so they never see more" reads backwards, since the T8 lets a leg reach 8,000 lb and a U-bolt starts bending sideways at about 600 to 1,500 lb (the guide's own figure). Fix the wording only: the T8 caps the load; a U-bolt may bend aft first and most likely keeps holding (Transom sec 10). (j) 15.8 says the battery box breather is in 15.4; it is in 15.2. (k) 15.8's humidity line names "the FSESC box", the old name for the VESC A box. *Boat 1 Route:* (l) Design Decisions R-4.3A cites sec 1 for "Boat 1 never reaches the Southern Ocean"; sec 1 shows the Atlantic loop but never says it. Fix: one line in sec 1. *Bottom Painting Guide:* (m) Sec 1 prices the barrier coat at $146 to $176 a kit and Boat 1's 3.5 gallons at $550 to $650; the kits cost $138.64 (gray, Amazon) and $128.24 (white, Defender), $406 for Boat 1's three (Bill of Materials). The paint table sent to Design Decisions R-2.1A has Trinidad PRO 75 at $280 to $330 a gallon; it cost $369.49. Fix: the paid prices. *Build Guide:* (n) 11.1 and 11.2 call the drogue attachments "the shared chainplates", and Lightning Ground System Guide 6.2 item 5 calls them "both drogue chainplates"; they are the two quarter U-bolts (Transom sec 4A). Fix the word. *Compute Bay Housing and Wiring Plan:* (o) Sec 8 says switched loads "live at the central node and the aft junction"; Boat 1 has no aft junction box (sec 4.4). Fix: drop "and the aft junction". (p) Sec 11 says the expander drives every relay coil except channel 13's; sec 10.2 lists only channels 1 to 4 and 6 to 12 and the steering cut coil. Channel 5 is spare (sec 11 table) and 14 to 16 have no driver. Fix sec 11's sentence. (q) Sec 13: "2 volts per square yard of loop at half a mile, 20 volts at 330 ft and 200 volts at 33 ft"; the last two are per square meter. Per square yard they are about 17 V and 170 V (same formula, inferred). (r) The flap after the backup cutoff: sec 5.2's drift line, Wing Power System secs 6 and 9 and Design Decisions R-4.3A have Pi B set the flap straight "once the converter has cut off for low voltage", but the wing box is fed from the bar that converter feeds, so after the cutoff it has no power. Fix: "just before the converter cuts off". *Electronics and Wiring Plan:* (s) A1: the safe-mode wire's 15k and 22k pair "so the Pi sees 3.3 V"; 5 V x 22/37 is about 3.0 V, as the Compute Bay Plan says. Fix: about 3 V. *Flow-Through Wet Lab Design:* (t) Design Decisions R-10.1A says the column stays full "so the SBE 45 cell never dries"; this guide (sec 6, Every station) has the SBE 45, 2 to 8 in above the waterline, drain for the 30 to 60 s drainback at each burst. Which holds turns on where the SBE 45 sits (open in Part 2). (u) Design Decisions R-10.1B: "the two blank spools are 1 in"; this guide has 1-1/4 in bodies, their job still open. Fix R-10.1B. (v) Sec 10 (The rules the software follows) gives the DO sensor a 60 s response (63 percent of a change) and "about five times that is a full settle", about 5 min, but the phase table gives it about 2 min inside a 4 min window; by the guide's own definition 2 min is about 86 percent (inferred). Make the two agree. (w) Sec 2 status against Bill of Materials 15.11: the Lasco bushing, NDS union and Oatey cement and primer read "to buy" (bought 2026-09-27 and 28); bronopol reads "TCI sells 500 g for $218" (bought 2026-10-01); the Iwaki reads $165 (paid $188.29 with shipping and tax); the PTFE coil tube reads "to buy" (BOM: open whether to buy again); the 12 V peristaltic pump is listed as bought and unused (BOM: went back for a refund). Fix: point status to the BOM. (x) Rule 9 and sec 10: the pump runs "only with valve 2 open and flow at the meter", but nothing flows before the pump starts; only the 20 s grace after a loss of flow lets it start. Fix: say the pump starts once valve 2 reads open and must see flow within the 20 s. (y) Sec 3: "Do not save money with ... unbranded wet sensors" comes right after the DFRobot DO sensor, which is unbranded-class and allowed by Science Payload Strategy (now sec 6, the grading rule; the pointer still says sec 13). Fix: "other than the DO sensor". *Glossary:* (z) The I2C expander (MCP23017) row ends "steering keeps its feed and charging resumes"; there is no charge stop. Fix: drop "and charging resumes". *Instrument Post Guide:* (aa) 14.4 says the wing is 8 ft tall; it is 6.5 ft (Wing Construction Guide sec 1). Its "about 5 percent of what the wing sees" is about 9 percent by area (1.3 against 15 sq ft); 5 percent holds only for tipping force with height counted. Fix both. (bb) 13.1 says a broken post leaves the barometer tube "reading roughly cabin pressure", but the break is 11 in above the deck, so the open end is outside: it reads outside air with no port (wind error) and can take water. Fix the line. (cc) 13.1's list of what is lost leaves out the horn, which is on the post (it may survive if it sits below the break). *Lightning Ground System Guide:* (dd) 6.2: item 2 says that if the motor case reads tied to battery negative, the case wire becomes the single negative link; item 7 still runs one negative wire to the junction, which makes two. Fix: item 7 says its wire is left off in that case (item 2's own rule, inferred). (ee) 5.3 (Build the trunk and junction) puts the junction "at deck level", yet the trunk runs about 5 ft down the pylon from under the deck to reach it, by the battery trough. Probably the cabin floor; say where. (ff) 5.3 (The instrument post lead) has the post's deck stub carry "the GPS ... coaxes", while 6.2 item 9 says the GPS antennas are not on the post. Both hold: the deck GPS antenna sits on a pad beside the post and its one coax uses the stub; the other antenna is on the pylon (Instrument Post Guide 11 and 13.2). Fix: "the deck GPS antenna's coax". *Rig Base Two Plate Design:* (gg) Sec 3 (Bolt grade): a corner bolt at mast break, about 11,000 lb, is "about 1.2 times on that yield" only at the top of the 10,000 to 13,000 lb yield range; at 10,000 lb it is about 0.9 times (inferred). Fix: give the range (sec 7 has the corner pads taking the corners to about 1.8 times). (hh) Sec 7 (Load figures): the service pull of "about 8,300 lb" on the windward row fits a 24 in spacing; over the true 21.5 in it is about 9,300 lb (inferred). (ii) Sec 7 (Plate 3 and its twelve base gussets) still says "Open: the corner pads; Mike's yes settles it", and sec 5's Check first waits on them; they were decided on the shop sheet and the BOM has them bought. Fix: drop both. (jj) Sec 5, Build the base: step 11 sets plate 3 "on the glassed top of plate 1" while the bed is wet, but no step glasses plate 1's top. Fix: a step before step 9 (inferred). (kk) Sec 1 rule 9 and sec 5 step 8 call for "test torque" on every main bolt, and no torque is given for the 3/4-10 bronze nuts at the dry fit, the fit or the re-step passes. A number to work out, set by the bronze nut. (ll) Sec 3A (The bearing): the refit checks compare the ring's breakaway torque "against the as-installed figure", but no install step writes that figure down. Fix: one line in sec 3A, Mounting it, or drop the comparison. *Routing Guide (Boat 2):* (mm) Sec 6 (also 1.3 and 14.2) says stay at 38 to 40 S; sec 6.1 and 2.2 put Leg 5 at 45 S and Legs 6 and 7 at 48 S. Make them agree. (nn) 2.1: the planning fouling loss (20 to 40 percent by month 12, 30 to 50 by month 18) does not match the Fouling column (0.85 to 0.97) or Leg 11 at 85 percent; the guide says the column was worked for Coppercoat and not redone for the hard paint. A number job. (oo) Secs 3 and 13: Legs 1 and 10 "hold 90 percent and top to 100 percent on sunny days"; there is no 90 percent target and no top-off (Design Decisions R-4.1E). Fix: say what the battery does under the surplus rule. (pp) 11.2 (Wing loss): "otherwise feather-and-drift"; with the wing gone there is nothing to feather. Fix: "drift on bare-hull windage". *Science Payload Strategy:* (qq) Sec 4 gives Boat 2 "the pCO2 unit moved over from Boat 1", and the markets table (sec 2) has Boat 1 building the mCDR record; Boat 1 carries no pCO2. Both hold only under sec 2's plan, if a unit is ever bought. Fix: add "if one is bought" to both. (rr) Sec 3 holds Boat 1 to A+ "across chemistry, physics, optics and acoustics", but bio-optics is menu only. Fix: name what covers optics (the camera, if meant) or drop the word. (ss) Sec 5 (The hydrophone stays outside): the tap test's rubber sleeve is "cheap before launch, impossible after", but the sea trial is afloat; it likely means the lake trial before the ocean launch. Fix the wording. *Steering System Handbook:* (tt) 2.1 gives the rod load as 11 to 40 lbf; the loads table at the 13 in station gives 10 to 37 lbf (11 to 40 looks like the 12 in station). Fix: 10 to 37 lbf. (uu) 2.4 puts the stern measuring afternoon after both sec 4 checks, but sec 4's installation sequence does Check 1 (rear mount stiffness) only at step 4, after the rear mount is set to the actuator. Make the order agree. *System Settings Sheet:* (vv) Sec 7: "Pi A turns the em-trak on (relay channel 4) when GPS A fails"; the em-trak sits on a normally closed contact, so it is on unless channel 4 is driven. Fix: Pi A releases channel 4; the software must drive it that way round. *Transom Drogue Box Guide:* (ww) Sec 6 says "not the nitrile BUSY-CORNER caps (bench use only)"; that order was cancelled (sec 9, BOM). Fix: drop the bench-use note. (xx) Sec 4A (Chafe) sizes the sleeve on "the roughly 20-day exposed Horn transit"; Boat 1 sails an Atlantic loop. Fix: say it is sized for Boat 2's Horn case, which covers Boat 1 with room to spare. (yy) Sec 5 never says when the coils are wound onto the strap, or how they come to sit at the horn crests on packing day; the sec 4 order does not mention them. Fix: one step in the sec 4 order. *Underwater Camera Port Guide:* (zz) Sec 1 prices the G10 sheet ($45) and the EPDM gasket ($8) as buys; the BOM's camera row has the gasket, G10 ring and sleeve from stock. Fix: from stock. (aaa) What settles the factory-made LED board: this guide says the UV-C card check and the 30-day photo pair; the Electronics plan says Mike's go. Make them say the same. *Wing Construction Guide:* (bbb) Appendix A5's heading says tail ribs "2 to 3 pieces"; Stage 12 builds the tail from 36 slices, T01 to T36. Fix the heading. (ccc) Stage 3 says two layers of 17 oz biax is "roughly 1/8 in"; sec 2 rule 4 and the five mistakes give three layers as about 1/8 in, so two are nearer 3/32 in (inferred). Fix Stage 3. (ddd) Stage 3 says the spar walls are "about 1/4 in thick"; they are 3/4 in foam strips plus glass. Fix the line. (eee) Sec 5 and Stage 10 give the lead as 2 lb bars, 14.4 lb on hand; the BOM has two 2.2 lb ingots and a 10 lb ingot. Fix: as bought. (fff) Sec 5 prices the CNC rib cutting at about $500 and Stage 1 reads as still to order; the BOM has it bought 2026-09-05 from Crimson Cutting Solutions for $825, and Stage 6 says the ribs are cut. Fix: as bought. (ggg) Stage 12 (Fixed tail and tail flap) step 4 notches "the back edge" for the give-way spring before the flap is cut off; the spring sits in a pocket in the flap's front edge (Wing Trim guide sec 6), so the notch belongs on the hinge line, the fixed tail's back edge after the cut (inferred). Fix the step. (hhh) Stage 13 step 3 checks the lean "24 in up the exposed mast", but only about 3-3/8 in of mast shows below the socket (Stage 4). Fix: a check point that exists. (iii) Stage 13 gives no torque for the two 3/8 in mast bolts (the boom bolts have about 130 in-lb). A number to work out. (jjj) Stage 11 step 6, "Seal both holes", does not say which; probably the meter arm's and the air terminal's bolt holes (inferred). *Wing Power System:* (kkk) Sec 1A's slip ring drawing (Reference/Wing HC2549 Compass Install 2026-10-01.png) is out of date: cable down the mast and drive tube, plugs at the ring's leads, a 5/8 in conduit down the trailing edge, the drip cup hung from the bar. The text has the root PEX through the mast plate, butt splices and the cup clamped on the tube; a note under it says follow the text. Needs redrawing. (lll) Sec 8.6 never says where the wing Cat6's own shield goes. Claude's pick by the one-end rule (sec 1 rule 10): join it at the splices to the RS-485 cable's shield ring, so it is grounded at the hull end, and leave it open at the tip (inferred). *Wing Trim Actuator Installation Guide:* (mmm) Sec 7 Step 5 (Test 1) holds the rod at a soft limit, flap at 30 degrees; System Settings Sheet sec 8 and Wing Power System sec 10 say "rod locked at full extension". Make the three agree. (nnn) Sec 4 Step 3 drills the flat tab's 10 mm pin hole with a 25/64 in bit (0.391 in), a hair under the 10 mm pin (0.394 in). Fix: a 10 mm or letter X (0.397 in) bit (inferred). *Wire and Cable Buy List:* (ooo) The top says every wire is tinned except the indoor Cat6 (B3), but the wing's 8 AWG ground wire (C5) is bare copper, and Mike's shielded Cat6 (C5, C8), the Belden 6504FE (C1) and the Cat6 patch-cord pairs (C7) are most likely not tinned (inferred). Fix: list the exceptions. (ppp) A5 says "Buy the green sets below", but the sets listed are red and black. Fix: list a green 6 AWG set, or say the red and black get green tape, as A5's shelf line already says. (qqq) B1 says buy 8 more 6.6 ft cords ($134); with the two Iridium cords that do not exist taken out, 14 are needed against 8 on hand: 6 more, about $100 at $16.69. Fix the heading and the rough total. (rrr) E7's diode count leaves out the two 1.5KE33CA in the actuator's surge clamps and the two 1.5KE12CA still to buy (Wing Power System 8.6). Fix: add them or point there. (sss) C5's 8 AWG bare solid ground wire is a Home Depot by-the-foot buy (about 8 ft, about $9), a cart of its own; Amazon was not looked at. Fix: look on Amazon first, by Mike's seller order. Rewriter reports: _v104a_work/rewrite/reports/. *Design Decisions:* (ttt) R-1.3 carries the flap actuator at about 2-1/2 lb; Wing Trim Actuator Installation Guide sec 2 says about 2.4 lb. Fix: R-1.3 to match the guide's seller figure. *System Settings Sheet:* (uuu) Parameter 29 still says to ask Dacian at Electrodacus if the unplugged reading is unclear. Fix: drop the line; the sheet should give the answer itself. *Documents: as named.* At v10.5: The plain fixes are written into the v10.5 guides. Every sub-item that needs a number, a look or a choice stays open.

498. Left over from the v10.4a write-in (Claude, 2026-11-01). Found by the writers; nothing below is decided. (a) The em-trak on backup power: the house bus's 12 V (line 8) is on the branch bar, not the backup-fed bar, so with the main side dead the em-trak's bus interface may be unpowered and Pi B may not see its AIS targets or position (Electronics plan 6.4 Open line). (b) Converter input protection: fuse or breaker and its size not picked (30 A by the main board's 1-1/4 rule, a guess); room on the backup battery board for it, the BatteryProtect and pump 2's surge diode not checked; pump 2 takes the spare breaker spot that was kept for Primelink unit B. (c) The Argodiode jumper's wire size is not stated; the main bus board drawing gives line 1 no stud of its own (written as "the free stud at line 1's spot"); what the minus half of the backup-fed bar pair carries is not written (the converter's minus is drawn to the - branch bar). (d) Failover time: Compute Bay 4.3 (about 30 minutes for a Pi that never starts) against Build Guide 11.1 (under 90 seconds); not picked. (e) Drogue firing: fire both channels at every deployment (Transom Drogue Box Guide sec 5) against fire Release Node B only if the first does not confirm (Compute Bay 10.3); not picked; with the main side dead, one horn at a time. (f) Build Guide 11.2's lake link-loss step against the new rule that the boat returns to its route when the link drops. (g) The backup battery's monthly exercise to 25 percent against the 30 percent cutoffs, and how it discharges (the converter is now a path to the main side); not decided. (h) Pi B's wing adapter: where it joins the wing CAN link and where the terminators go (Wing Power System 8.7); the Wing Trim guide still describes only Pi A's adapter. Settled 2026-11-04 (item 519 (f)): at the wing box. (i) Where pump 2's two signal wires and Pi B's converter remote pair enter on Pi B's side, and which relay module switches pump 2's manual-on. (j) The Compute Bay expander pin count (sec 10.2) against the drawings' "3 pins spare" now channel 12 and opto input 2 are spare. (k) The shunt move on Boat 1's finished main bus board (item 487): was it done? Asked 2026-11-01. (l) BOM 15.2A's Water Witch line says "$139 estimate"; paid $138.58. (m) The Ultima switch's lead colors not found; drawn by function. (n) The BMS box diagram's PNG preview was made by a screenshot, not by the usual tool (PyMuPDF is not installed in the cloud). Writer reports: _v104a_work/reports/. At v10.5: (b), (c), (h), (k) and (l) are written into the v10.5 guides. The rest stays open.

492. Single points of failure: make the full list for Mike to review, in its own session (Mike, 2026-11-01: "a list of spof would be good to review, too, but not in this chat"). A single point of failure is one part with no backup whose failure ends the voyage. Go box by box and run by run through the v10.4 guides (not only the failure tables), and give each its plain consequence and a rough fix and cost. Already decided: the single rudder actuator is accepted for Boat 1 (Mike, 2026-11-01: "Accepted for boat 1"). Seeds found 2026-11-01 from the failure tables: the central node, which drives the rudder (Compute Bay sec 11, "Node dead"); the control CAN bus as the only steering command path (Compute Bay 10.2; the node has one CAN port, Electronics plan 5.4); the wing's one control path, one trim actuator, slip ring path and cable (Wing Power System sec 9); the motor controller, VESC A (Build Guide 5.1.1; not voyage-ending, it costs doldrums motoring and a lee-shore claw-off).

488. Left over from the 2026-11-01 write-in (Claude). Found while writing in item 486; nothing decided settles them. (a) The wet lab line (line 9, 16/2): "good to 22 ft" is worked at about 4 A; at the converter's full 10 A, 16/2 holds 3 percent only to about 9 ft (inferred); the measured run settles it (14/2 or 12/2 if longer). (b) The drains of the post wind meter cable and encoder A's Belden lead at the node: the guides' rule says unlisted shields float; the wiring review suggested drain to 0 V at the node only, like the post lights cable. (c) Compute Bay 4.1 and 11, Box Wiring Sheet A1: the INA226 in Pi A's feed (all three went back 2026-09-08). (d) Steering System Handbook sec 9.5 (Release): Release Node B "own fuse" (open; Compute Bay 10.3). (e) The two light converters in the node take no surge diode of their own; the node's 24 V carries one at its 5 V converter (inferred enough; say so in A3). (f) The 1k's lead on the bus board, + bar to strip, a few inches, heat-shrunk: a loose lead there also stops charging, like the 1k failing open. (g) Backup Battery Board Layout 2026-10-15: the 10 A Orion output fuse against its own 1-1/4 rule (7.5 A), and the main battery wires entering from the left edge (Mike's call). (h) Electronics plan 7.6, "Wiring a 75/15", PV order (labels settle it). *Documents: as named.* At v10.5: (c) and (d) are written into the v10.5 guides. The rest stays open.

484. Box against box, board and parts: what disagrees (Claude, 2026-10-31, from Mike's "PLease check all boxes against other boxes and boards and parts"). Fix at the next write-in; nothing to decide unless marked. Fixed 2026-11-01: (a), (b), (c), (d), (e), (j), (k), (n), (o), (p), (q), (r), (u), (x), (y), (bb), (kk) (by item 486); (g) in part (PV pair at the bottom edge, bus bars bought; the Orion fuse rule and the left-edge main wires left); (l) Sheet A15's wording (the fuse itself still open); (t) in part; (v) Pi A entry 1 sealant-filled (the wing can holes left); (w) on the tracker; (ll) in part (the C4 and 16/2 budgets). Left: (f), (h), (i), (m), (s), (z), (aa), (cc), (dd), (ee), (ff), (gg), (hh) in part, (ii), (jj), (mm). Three read-only checks: both ends of about 85 runs, every board line against the box it feeds, and every box's parts against the BOM and the order tracker. Detail: Reference/Wiring Review 2026-10-31.md sec 8. Wiring: (a) Reference/Main Bus Board Drawing 2026-10-06 (and the Layout) draws each solar fuse at its controller's BATT + terminal (the board as built has them at the bar, Mike's photo 2026-10-31, item 487: drawing only); Electronics plan 7.6 puts it "within a few inches of the busbar", which is right: at the controller end the 14/2 from the bar to the fuse has no protection from the battery side, the fault 7.6 gives as the fuse's reason. The drawing also joins the five + and five - leads onto shared lines; each controller has its own 14/2. Redraw. (b) The same drawing has no charge-stop 1k resistor, yellow-wire strip or thin run to the node. Add them (in the item 482 (f) form if Mike takes it). (c) The 6 AWG link from the + solar bar to the + 400 A bar has no fuse ("none needed, short links"), where 7.6 fuses every main branch; Claude's view: fine while it stays under about 7 in, as drawn, the usual limit for an unfused lead off a fused bar; write that into 7.6. (d) Electronics plan 7.6 line 10 (Pi A): 16/2 at "about 4 A" is good to about 22 ft by the plan's own 3 percent method, not 36 ft (36 ft fits about 2.5 A; the DDR-60L-5 tops out near 2.8 A at 24 V, inferred): fix the load or the length. (e) The 7.6 load sum books the wet lab at 4 A and both pumps at 3.5 A; worst case is about 10 A and 5 A, about 78 A in all, still under the 100 A MEGA. (f) PV + and PV - are in opposite order in 7.6 ("PV -, PV +") and Reference/Solar Surge Wiring 2026-10-12 ("PV +, PV -"); the labels on each controller settle it. (g) Backup Battery Board Layout 2026-10-15 brings the PV pair in at the top and the main battery pair from the left, against its own "cables leaving the bottom edge". Its Orion output fuse is 10 A, against its own rule (1-1/4 times 5 A, next size up, is 7.5 A); 10 A still guards the 14 AWG. It still lists the bus bar pair as "Buy" (bought 2026-10-15). (h) The two point-to-point Micro-C runs (Pi A to VESC A serial and kill; Pi A to Pi B alive line) have no core colors and no drain landing at either end; a drain landed at Pi B ties Pi B's floating side to Pi A's bond stud. Add with item 482 (l). (i) No doc says where the FTDI cables' ground wires land at the wet lab box (the SBE 45's RS-232 needs its ground joined to the sensor's 0 V; the DO's RS-485 normally wants one too) or what to do with the spare FTDI wires. (j) Electronics plan A4 powers the SBMS0 "through the SBMS0's own supply lead"; Battery Box Part 8 powers it through the cell ribbon (pins 11 and 12 from W8, behind its fuse link). Part 8 is right; there is no separate lead. (k) The aft junction build sheet's 1.5KE33CA across the 24 V input is not in A6, Sheet A6, the BOM aft junction line or Lightning Guide 7.7. (l) Release Node B: Sheet A15, A15's contents and Compute Bay 12 draw or name a fuse in its feed, still open (item 352 (a)); the central node's release feeder shows none. Draw both the same once Mike picks. Sheet A15's "house-side branch" means nothing: both release feeders come off the one branch bar. (m) VESC A: VESC A Box Build Sheet 2026-10-26, VESC A Box Build Prep 2026-10-24 and VESC A Box Wiring 2026-10-14 show the motor leads entering by three PG16 with the lugs cut, "(Mike, Oct 24)"; A7, Sheet A7, Wire List A3, BOM 15.5 and item 450 keep it open until the motor is mounted. Mark the drawings open. The Wiring drawing still bolts the Flipsky to studs (now four flat-head screws into its own holes). Numbers and stale text: (n) item 481 missed two drawings: Stern Release Wiring 2026-10-27 (gland circles and table still 3, 4, 4a; should be 11, 12, 13, PDF too; and say in A3 which of 12 and 13 runs to port) and BMS Box Wiring Diagram v10.4 (both copies: "temp chain in (entry 18)", now 21; 18 is the horn). (o) Build Guide 8.3 still says the Starlink feed has its fuse in the aft junction (moved to the node). (p) Sheet A11-A's header says "USB TO THE HUB BOX" (to Pi A since 2026-10-20), and puts the arrestor "a few inches from the deck stub", where the Post Guide 12.3 and Lightning Guide 7.1 have the stub and the deck terminal about 2 ft apart and the spot open. (q) The post lights and bow lantern cable (C4 18/4, item 467 (p)) is not in Wire List B2 (still "Open: which four-conductor cable"), C4's job list, A9 or A6; Wire List C6 still plans the UV-C run on "the C4 leftover". (r) Wing Power System 8.7 and Sheet R1 still treat the wing Cat6's seal at hub box port b as open; it is measured, 0.225 in (Mike, 2026-10-29). (s) Reference/Nav Light Layout 2026-09-22, which the Post Guide cites, still says the lights run off the 24 V bus with no converter. (t) Electronics plan 7.6 calls the Orion remote "a thin wire" (14/2 everywhere else), leaves the Pi A hub lead's 3 A fuse off its "still fused" list, and says "the aft junction 20 A" for line 6, which feeds the switch box first. (u) Sheet A15 and seven other places say the switch is on "the house branch"; the board has one branch bar. (v) Gland notes: the 22/12 (0.24 in) is a PG11 at node entry 17 but a PG9 at the BMS and battery boxes (PG9 fits); Pi A entry 1's 16/2 is not marked sealant-filled; the Wing Can Spec Sheet drills its PG9 holes at 0.60 in, against 5/8 in in 7.1 (a PG9 thread is about 0.60 in, so no clearance; inferred). Parts and counts: (w) 8-channel relay boards: BOM 15.8 and the tracker say two bought; the order log shows two on 2026-08-16 and two on 2026-08-18 (four, if the quantity is modules), and Wet Lab Box Layout 2026-10-15 says "4 on record, 2 used". Three are needed (node 2, wet lab 1). (x) Klnuoxj 24 to 5 V: BOM 15.8 and the tracker say three needed; the wet lab box takes a fourth from the shelf (eight shipped). (y) Nucleo: BOM 15.8 and the tracker say a third from the 2026-09-24 order goes back, while the wet lab box needs a third (on the Buy list). If a third came, keep it. (z) 5 A stud breakers: the BOM says about 30 bought 2026-09-07, but that order was 30, 20, 50 and 6 A (the 6 A are 12 V only) and Mini ATM blades; the 5 A stud ones are the eight of 2026-08-16, against nine needed (seven main board, two backup board): about one short. (aa) DIN terminal blocks: about 170 needed across the boxes (guess), against the Erayco (20) and MELIFE (30) kits named; other kits on hand are named nowhere (two "DIN Rail Terminal Blocks Kit" of 2026-08-16, GUETNEU, PHITUODA; the 76 ST2-2.5 are push-in, not screw). Count the shelf before the loom. (bb) DIN fuse holders: 19 needed (20 if the wing box fuse goes on DIN); BOM 15.7 and the backup board sheet count "four the emergency bank does not need", which the order log does not show (only the MECCANIXITY pack; the UK5 6-pack was cancelled). (cc) Sealed inline fuse holders: about 13 wanted, 9 on hand (item 401 (p)); item 482 (w) and a DIN holder at the wing box bring it near 9. FHAC0002ZXJ holders are "on hand" with no order line or count. (dd) The 2026-10-03 TICONN box is the wet lab box in A18, BOM 15.11 and both wet lab drawings, and "maybe the second drogue box" in the tracker and item 374; it is ABS, and the drogue box must be fiberglass, so it is the wet lab box. (ee) The fifth Altelix 4-port of the 2026-10-14 pack has no job written; Pi B's USB split gland (A2 entry 7) has none picked: that is its job. (ff) The Oct 7 Taidacents: the tracker says for the science lines, the guides say one for the wet lab CAN drop and one with no job; the Sep 26 pair is "ORDERED" in BOM 15.6, "Here Oct 17" on the Parts tab and "Coming Sep 30" on the On the way tab. (gg) 1.5KE12CA: the tracker's Buy list note says a Littelfuse 5-pack on Amazon (B00LQQ47BK); its own answer column, BOM 15.8 and Wing Power System 8.6 say no Amazon listing, Digi-Key. (hh) BOM: the CAN line counts the two bus-power breakers again (they are lines 1 and 8 of the fifteen); "Humidity breakouts x5 to 9, $45 estimate", against three used and ten AHT30 on record; two AS5048A rows on the tracker; the DDR-15G-5 at "$20.50 at Jameco" in A11, paid $25.00 each on Amazon; the Pi boxes still a "$144 estimate" (bought 2026-08-04). (ii) Hub box: A1a says "built; not logged", the tracker says "Box not picked"; the two DJC 10 x 8 x 4 in boxes of 2026-10-14 match the drawing's size. (jj) Stale tracker rows: the level shifter still "inside the Pi B box" (no-job list), the USB isolators still "ON THE WAY". Calls for Mike: (kk) The C4 18/4 roll looks short. Runs now on it: the wing actuator, two puller runs, the bilge cable, the post lights, the bow lantern and the UV-C run, about 80 to 95 ft against 50 (guess; nothing measured). Mike's "no second roll" (item 467 (p)) was on about 50 ft. Claude's pick, no purchase: take item 482 (a) (the bilge cable gets short), put the bow lantern on a 12/2 offcut from the node (about 80 ft of 12/2 spare; a bigger wire is always allowed) and the UV-C run on a 22/12 offcut (milliamps; about 50 ft spare); that leaves about 45 to 50 ft on the 18/4. (ll) The 16/2 is about 75 ft short (item 483 (q)): the spare 12/2 stands in for the long 16/2 runs (7.6 allows it), and item 482 cuts about 25 to 50 ft. (mm) Parts on hand with no job that could fill open box jobs instead of buying (Claude's opinion; sizes to check against each job): the third TICONN or the 9.5 x 5.5 in box, the second QILIPSU, two Raculety IP65 (one may be the BMS box), a YINGXINELCT 8.66 x 5.71 x 3.15 in, a Fielect 7.40 x 4.72 x 3.07 in, LeMotech mini boxes x5, Zulkit boxes and the DJC boxes, against the open jobs: the wing box (a TICONN 5.9 x 5.9 x 3.5 in is on the to-buy list), the two Iridium boxes, the detector mini-box, the MOTU M2's box and the PoE light driver's box. Also no job: two Pololu D36V6F3 (item 482 (k) uses one), three Fafeicy boards, ten MOSFET modules, four Klnuoxj, three carriers, one SN65HVD230, seven AHT30, the second SFP module, about 20 breakers of sizes not used, the Heyco cord grips 20-pack, the photocell 2-pack and the precharge resistors. *Documents: as named; order tracker.*

483. Docs that disagree or are stale, found by the wiring review (Claude, 2026-10-31). Fix at the next write-in; nothing to decide. Fixed 2026-11-01: (a), (b), (c), (d), (e), (f), (i), (k), (l), (p), (q), (r), (t), (u), (v), (w), (x); (j) is an Open line now (the fourth expander input: Compute Bay gives it a release-bus readback, the Build Guide says none). Left: (g) the FHAC0002ZXJ link, (h), (m), (n), (o), (s). Detail: Reference/Wiring Review 2026-10-31.md. (a) Bilge Pump Wiring 2026-10-31 gives aft junction rail 1 block 17 and rail 2 blocks 1 to 3; the build sheet has rail 1 blocks 11 and 12 and rail 2 blocks 1 and 2. (b) The aft junction build sheet's "feed dead ... or lift line 6's lug" no longer kills the box: it is also fed by channel 3 (normally closed, live with the coil off), channels 6 and 12, trunk core 8 and the pump running cores; only the main battery switch kills it all. The bilge sheet's "lift the lug at the 5 A breaker" has the same gap. (c) Build Guide 8.2A and Electronics plan sec 8 say "four switched outputs" are fused at the node; it is six. Sec 8 also says two of the three relay modules are not needed at the node; it uses two 8-channel boards and two 30 A modules. (d) Electronics plan 6.4: "these lamps are small and need no 30 A relay, unlike the motoring whites"; the whites draw about the same as the bow and stern lights together. (e) Electronics plan 7.6 lists "the watchdog rails" as fused and says Iridium, the watchdogs and the steering feed "get parallel-fused feeds from different buses"; none of that exists in any box or sheet (steering is single string by decision). (f) Build Guide 3.6 says each bilge pump is wired "from a different bus"; 7.6 puts both breakers on the same branch bar. (g) Order tracker Parts tab: the central node row lists eight DIN fuses (ten); the fuse holder row says 19 in one column and "15 needed" in another; the FHAC0002ZXJ row links B093LKN3YH, which is the USB isolator. (h) Item 478 (j) is wrong: the expander uses all 16 pins (11 relay outputs, the steering cut, 4 inputs); close it. (i) Node entry 19 (chain 2) still says "PG7 or PG9"; Wire List C1 puts chain 2 on the 22/12 (0.24 in), a PG7. (j) Sheet A3's notes route a release-bus readback through the opto board; Electronics plan 4.1 and Node Boxes read only the two Water Witch states (a third version for item 352 (e)). (k) Electronics plan sec 3 box table still puts the hub box glands on "Top"; USB Hub Box Wiring 2026-10-20 still says "TOP WALL", "Doc set v10.3" and "BOX NOT PICKED"; A1a numbers split gland B's ports 2 to 5 on a 4-port gland (use a to d). (l) Sheet A12 calls the detector board "the one solder job allowed"; the G2 drive's terminal blocks, the Pololu terminal blocks and the UV-C board wires are bench solder jobs too. (m) Box Parts With Photos 2026-10-15 still lists ADuM1201 isolators for Iridium, breather vents in Pi A and Pi B, two USB leads to Pi A, the CAN adapter straight to Pi A and Pi B's fuse as open; archive it or redo it. (n) The INA226 is still in Pi A's power path (A1, Sheet A1, Compute Bay 4.1 and 11), though all three went back 2026-09-08 (item 427 (c)). (o) Electronics plan 5.2 leaves Primelink A's house tap out of the drawn backbone; 5.3 counts six house drops; no 7.6 line feeds Primelink A. (p) Box Wiring Sheet R1's fit-out flags still say "entries 4, 11 and 19 all carry lighting" and "whether the wet lab line leaves entry 13". (q) Wire List A9 counts the nav lights, em-trak and science group runs on top of the five C2 runs (three counted twice); the 16/2 is the short roll now (about 175 to 225 ft wanted against 100 on hand plus 100 held, guess), not the 14/2 that item 478 (o) names. (r) The aft junction build sheet's "Cables not named: ... encoder lead" against its own gland table and A6, which name the Belden 6504FE. (s) Wet Lab Box Parts 2026-10-15 still lists a breather vent. (t) The 7.6 load sum's "aft junction 5.5" is the switch box; the aft junction itself draws about 0.1 A. (u) Box Wiring Sheet A4 notes say the VE.Direct remote cables "leave from the central node"; Battery Box Part 8 has them meet on the bus board. The BMS box diagram says its USB lead enters the hub box's "top" split gland (a side wall since 2026-10-31); Reference/BMS and Balancer Wiring Sheet 2026-10-03 says "the BMS box's small bottom gland" (now the split gland). (v) Wing Power System 5 books the tip regulator's draw for a Pololu D36V6F5; the tip has the DROK (8.6), idle draw unknown. (w) Instrument Post Guide 10.1 joins the two whites "at a small terminal block inside the post", against its own 10.3 "Connectors below deck, never inside the post". (x) The Post Guide counts "three antenna coaxes (GPS, Starlink, Iridium A)" through the deck stub; Starlink is a Cat6 and a 16/2, so 9 cables and the tube, and its "cable ends go through bare" cannot hold for the three premade Cat6. *Documents: as named.* At v10.5: (n) is written into the v10.5 guides. Still open: (g), (m), (o), (s).

460. Build Guide sec 6.5's upwind limit (60 to 70 deg true) looks optimistic; check at sea (Claude, 2026-10-27, from Mike's "how tight to the wind"). A worked estimate that adds the hull's windage and the keel's sideways slip puts the wing-only limit near a beam reach: heading about 80 deg off the true wind, real path about 90 deg (80 to 100), the same from 5 to 30 knots, flat water. Not measured; the hull windage and keel grip are estimates. At sea trials, log heading, track and true wind with the motor off at the closest heading the wing holds; then fix the sentence at the next doc set and tell the route planner the real figure. Detail: Reference/Wing Upwind Estimate 2026-10-27.md. *Documents: Build Guide sec 6.5; Routing Guide.*

419. Gaps found drawing the VESC A box wiring (Claude, 2026-10-14). (a) No doc names the motor temperature pins: drawn on the Flipsky sensor plug's TEMP and GND, the usual VESC place (inferred). (b) The 2 AWG feed: Electronics plan A7 and the 2026-09-26 capacitor drawing say 5 to 6 ft; Reference/Main Bus Board Drawing 2026-10-06 says about 10 ft. The routed length settles it; the Wire Buy List's 20 ft of each covers either. (c) One COMM ground pin serves both the UART backup and the motor sensor; the docs say the pigtail splits but not how (the JST-PH wires are about 26 to 28 AWG, below a WAGO 221's 24 AWG floor). (d) How the motor's phase lugs meet the Flipsky's phase outputs is not written. Drawing: VESC A Box Wiring 2026-10-14.

413. Gross tonnage: over 4, where the Coast Guard says it starts to matter (Mike, 2026-10-14). The USCG asked Mike the boat's gross tonnage; he did not know, and they said it only matters if it is above 4. No guide gives it. Worked by the USCG simplified rule for boats under 79 ft (46 CFR 69.203 and 69.209): gross tons = 0.5 x length x beam x depth / 100 for a sailing boat (the wing makes it one; a powerboat uses 0.67, about a third more). Length 25 ft, beam 8 ft (Build Guide 1.1). Depth is from the top edge of the hull side amidships down to the bottom of the keel; on a faired full keel the keel counts and only 75% of that depth is used. Masts, the wing, cabins and deckhouses do not count, and loading does not change it. So for this hull, gross tons = 0.75 x depth in feet, and depth = the 3.5 ft draft + the hull side height above the water amidships. Under 4 gross tons needs depth under 5 ft 4 in, so a side height under about 1 ft 10 in. Mike, 2026-10-14: the side height is more than 1 ft 10 in, so the boat is over 4 gross tons and the USCG's extra paperwork applies (about 4.1 at a 2 ft side, 4.5 at 2 ft 6 in, 4.9 at 3 ft). Do not try to get it under 4: only cutting the hull sides down would, at a cost in height above the water and self-righting. Net tons are 90% of gross (sailing, motor in the hull), about 4, under the 5 net tons needed for federal papers (46 USC 12102), so the boat can only be state registered under US rules, which bears on the flag choice in the rules and permits item (1B list below). Same for both boats: Boat 2's bow armor does not change the outside size. Still open: what the extra paperwork above 4 gross tons is (not found in the federal rules), and the real side height amidships (deck edge to waterline at design load, or deck edge to keel bottom directly) for Form CG-5397; the numbers given must be the real hull's. Written in at v10.3: the rule and the result in Build Guide 1.1, pointers in 11.5 and Boat 1 Route sec 4, the side height and the paperwork as Open lines. *Documents: Build Guide 1.1 (add the side height and the tonnage figure once known) and 11.5; Boat 1 Route sec 4.*

401. Numbers and small gaps found at v10.2, nothing decided (2026-10-08). (a) The A1 and A2 IMU disagreement limit has no number (System Settings Sheet sec 7, TO BE SET). (b) Done at v10.3: the wing CAN link at 250 kbit/s (Settings Sheet sec 9). (c) SBMS0 serial speed: 115,200, decided 2026-11-08 (item 509). (d) The JK balancer's 1.2 W ceiling (about 29 Wh a day at most) is not in the Build Guide 4.6 hotel table. (e) Done at v10.3: the wing compass at about 23 Wh a day (Wing Power System 5, Build Guide 4.6). (f) Electronics plan 7.6's 100 A MEGA sum still books about 1.5 A to the hub box; the hub now draws from Pi A's line (the total barely moves). (g) The hub box's SMA bulkhead likely needs a short SMA male-to-male lead inside to reach the dAISy's socket (inferred; no doc names one). (h) Overtaken: each tap cable has its own gland (Mike, 2026-10-13; Battery Box guide), so there is no bundle gland. (i) Which way the switch box's right-angle patch cords must point: read it off the switch before ordering (Electronics plan A6a). (j) Design Decisions R-8.3A and Instrument Post Guide sec 10.4 still say motion correction comes off "IMU A"; Pi A now has A1 and A2. (k) Electronics plan sec 8 says two of three 8-channel opto boards are spare; the tracker has five Fafeicy boards on hand. (l) The Lightning Guide's bar run list totals about 40 ft; item 364 estimated about 45 ft against 48 ft on hand: the run measurement (item 309) settles it. (m) The Transom Drogue Box Guide's parts list (sec 9) still names 3/8 in 316 thimbles ordered 2026-09-26; those went back Oct 1, and a US Stainless 316 5/16 in part came Oct 7 (probably thimbles, Claude's reading): check it is thimbles and fits the bridle rope, then fix the guide. (n) IMU placement: "one at each end of the plate" (IMU A1 and A2) and "the converter at the far end of the plate from the IMUs" cannot both hold; the Box Wiring Sheets draw A1 and A2 at the two corners of one end, the converter at the other; Compute Bay 4.1 and Electronics plan A1 should say which. (o) Battery Box Part 8 gives the farthest tap as about 35 in (Mike); the tap drawing draws W4 at about 42 in. (p) Inline fuse holders: nine on hand and seven used at the bus board, while v10.2 adds at least five more inline fuses (Pi A's 3 A hub lead, the hub box's 24 V, the wing box's 5 A, the tip's 1 A, the horn's 5 A) plus one per post feed (Claude's count): count the shelf before the loom. (q) The one 1/8 in G10 sheet on record (13.2 x 11.8 in) makes one 11.2 x 7.6 in compute box plate, not two (inferred). (r) Lightning Guide 7.7 asks for a TVS on Pi B's lightning detector lead; no part is named, and the 1.5KE33CA (31 V) does nothing on a 3.3 V line. (s) Electronics plan A2 entry 5 puts an optocoupler in Pi B's box; Compute Bay 4.1 runs the alive line through Pi A's PC817 board: whether a second board goes in Pi B is not written. (t) Box Wiring Sheets A7 draws a TVS on the VESC A feed; the Electronics plan's A7 text names none. (u) The MOTU M2 is on a hub port (written 2026-10-09), but where it sits and how its cable reaches the hub box are not written. (v) The bus board drawings put the battery switch ahead of the battery shunt (from Battery Box Part 8's wording); no guide says which comes first. The charge-stop 1k resistor and the remote on/off terminal strip belong on the bus board, but no guide says which bar or stud they land on, so they are not drawn. *Documents: as named.* At v10.5: (c) is written in: SBMS0 serial at 115,200 (System Settings Sheet sec 1, Battery Box setup).

404. Safe mode: points for Ken (software repo, 2026-10-08). (a) The guides say safe mode runs "its IMUs"; Ken's decision said IMU A, which is now A1 and A2: confirm. (b) The command signatures' sequence counter is kept on the SSD (Build Guide 8.3), which safe mode does not use: how the replay check works in safe mode is not written. (c) Still to prove on a real CM5: that its startup reads the header pin to pick the safe copy (Compute Bay 4.3, Open line). *Documents: Compute Bay 4.1, 4.3; Build Guide 8.3; software repo.*

320. Wet lab and camera port: what is left after v10.1. v10.1 writes in: no drip-tray leak sensor; the 360 degree foredeck fisheye (Hanwha XNF-8010RV; bought 2026-09-30 open box on eBay, $132, written into the BOM, Electronics and Wiring Plan, Design Decisions and System Settings the same day); the Iwaki bought; no paint on the de-bubbler; the simple reducing-tee de-bubbler with the Rain Bird drip emitter bleed; the flow meter's 3 to 24 V; the SBE 45 drainback sentence; and the camera port's UV-C as layout H (small 275 nm LEDs on a flat mask above and below the lens; the Seoul stars do not fit and are not bought). Still open: (a) where the SBE 45 goes, above or below the waterline (Mike's call; the claim that Sea-Bird wants it above is not in the SBE 45 manual; below, it never drains; the limit is room: 13.3 in tall with 6 in clear below and 12 in above); (b) the biocide reservoir: settled, the filter housing was ordered 2026-09-30 and is written in; (c) the camera port: three LEDs were bought (one eBay order, 20-15209-84182, 3 on 10 mm boards, $14.80, here 2026-10-09) against four in layout H; the mask and how three sit are drawn when they arrive; test each with the QuantaDose card first; the factory ring board (four Marktech MTSM280UV1-C3510-24) stays the fallback if they fall short. *Documents: Flow-Through Wet Lab Design 6 and 8; Underwater Camera Port Guide; BOM 15.8 and 15.11.*

319. The wet lab's 24 V feed: one check left. The steady 24 V converter (XWST, bought) is written in at v10.1. Open: where the flow meter's pulse wire lands, since its pulse now swings to 24 V. *Documents: Flow-Through Wet Lab Design 4 and 10; Electronics and Wiring Plan 7.6.*

2. Displacement margin. Estimates run 5,570 to 5,775 lb against the 5,500 lb basis (re-summed at v10.0). The Build Guide 11.2 weighing is the gate. Design Decisions R-1.3's weight table was re-summed at v10.0 with the can at 110 lb (Boat 1 about 5,775 lb; the range 5,570 to 5,775). Two of the three estimates sit past the 5,600 lb re-check line, so expect the weighing to matter. For Boat 1 alone, which leaves out the Cape Horn package, the strip and bottom-up estimates are about 5,435 and 5,505 (Build Guide 1.3), so only the itemized 5,775 is past it; the quoted range 5,570 to 5,775 mixes the two boats. *Documents: Build Guide 1.3 and 11.2, Design Decisions R-1.3.*

22. Heading wander. Log one hour of compass heading under self-steering once the boat floats. It checks the steering deadband (how far heading may wander before the rudder moves), which item 92q left as it is. *Documents: Steering System Handbook 10, System Settings Sheet 3.*

4. Camera head against the tube. Measure the Axis P1245 head against the 1-1/4 in bore of the G-10 tube before the tube is glued in. Aim check at 38 degrees. *Documents: Underwater Camera Port Guide 5 and 6.*

61. Bare shaft for the seal. Now part of item 173's haul-out list. The Lasdrop DrySeal D-100 is on hand; polish the shaft where its lip rides. *Documents: Build Guide 3.5, BOM 15.5.*

87. Aft junction box size. Planned at 12 x 8 x 5 in with 10 RJ45 couplers and about 21 entries. It now also holds the post wind meter's 5 V regulator (item 194). Measure before the loom; it may need a bigger box. (2026-10-30: the couplers moved to the switch box, so about 14 entries; the build sheet of item 467 needs a plate about 10 x 6 in and a base at least 3-1/2 in deep for its lower gland row.) *Documents: Electronics plan A6, Compute Bay 4.4.*

110. Antenna bundle through the post stub. Pass the real bundle (GPS, Starlink and Iridium A coax, plus the post cables) through a sample stub before the real stub is glassed in. Cable ends go through bare; connectors are made up after. If it will not pass, say so before the deck is closed. *Documents: Instrument Post Guide 8.*

126. Count the shelf before buying. The 2 AWG roll length (68 ft needed). The TVS bag: 1.5KE33CA surge diodes or 1N5408 flybacks. IP68 glands (about 120 needed, 50 on record). M12 vent plugs (one: the central node only, item 434). ADuM1201 isolators (three ordered, two delivered). Tylaska T8 shackles (four for Boat 1; the order looks like eight). Lead: 14.4 lb on hand; how much the wing nose needs now comes from the Stage 10 measurement, since the packs, pod and panels have left the wing. Then strike the Wire list buy lines that Mike's 2026-09-21 notes put on the shelf (NMEA 2000 cords, Cat6, 6 AWG, serial cables). *Documents: Wire and Cable Buy List, BOM, Electronics plan App B.*

29. Duckbill cracking pressure. At the Battery Box Part 10 check. Grease the lips first, then read light breath pressure on a clear vinyl tube taped to a yardstick. *Documents: Battery Box Building Guide Part 10.*

128. Prove both carrier slots. Fit the 4 TB NVMe drive and the Hailo-8L together on the carrier (the second carrier is on hand) and run both, before the wiring is committed. *Documents: Build Guide 8.1, Compute Bay 16.*

88. TSW202 bench test, five checks. Turn a PoE port off and on through the Web API; record the request and the firmware version. Read the same port over SNMP. Read per-port watts. Find out whether per-port power priority exists. Power all six devices (the five cameras and the light driver) at once and read the total. Pin the firmware. *Documents: Build Guide 11.1, Electronics plan.*

33. Nichrome bake-off. 28 AWG against 30 AWG, wet, at 24 V. The winner goes in Transom Drogue Box Guide sec 9. *Documents: Transom Drogue Box Guide 9, Build Guide 11.1.*

127. Iridium modem bench test. One of the two jobs that gate the wiring. The other is the Flipsky bench check (item 254). *Documents: Electronics plan, Compute Bay, Build Guide 11.1.*

172. Motor wiring: what is left. The sensor question is settled in Build Guide 5.1 (the 75200 Pro reads sin and cos on ADC1 and ADC2; a divider unless the bench check in item 254 says not). Left: size extra bus capacitance at the controller with the cold plate work, and measure the three phase leads before siting the controller. The controller is here (2026-10-07). *Documents: Build Guide 5.1, Electronics plan A7, BOM 15.5.*

173. The shaft run, at haul-out. Mike measured 8-3/8 in of bare shaft forward of the stern tube (2026-09-29), so the run fits with the L-110 and the Lasdrop; nothing shorter is needed on Boat 1 (written in at v10.1). Left: confirm with calipers that the coupling end is straight, not tapered; check for a keyway; and check Design Decisions' PYI PSS figure (7 in of bare shaft) against the study's 4.7 in. *Documents: Build Guide 3.5, Design Decisions R-3.5C.*

86b. Measure for the three hull-glued boxes. The hull laminate thickness at each spot, and the size of each plate: Pi A, the motor controller plate, the network switch (the motor cooler plate is gone: item 466, 2026-10-29). Taken at the boat. *Documents: Compute Bay 2, Build Guide 5.2.*

95. Desiccant in Pi A. Whether Pi A also needs a desiccant pack once its back sits on the cold hull. Settle it with the 86b measurements. *Documents: Compute Bay 2.*

167. Measure the tiller parts. Poke the wood hard with an awl first. Then measure the tongue's height above the casting and whether it has room for a second hole, the hinge pin diameter, the tiller's width and depth at the 13 in mark (the actuator station) (for the plates), the pin's height above the cockpit floor (sets the base bracket height), and the actuator's eye and pin (Build Guide 3.8 says a reamed 7/16 in hole). *Documents: Steering System Handbook 2.4, 3 and 4; Build Guide 3.8.*

168. Hydrophone fin station. Mark the station on the hull now (starboard, middle third of the waterline length, 12 in above the bottom of the keel) so no stand or sling strap lands on it; fix it after the keel measurements. Before cutting, check from inside where the gland's hole comes out: at 12 in above the keel bottom it may open into the lead or its cap; raise the fin if so (Science Payload Strategy 5). The gland (Jacob WADI K257-1012-00) is bought and written in at v10.2; on arrival read its stainless grade (316 or not) and its thread length. *Documents: Bottom Painting Guide Step 0, Science Payload Strategy 5.*

214. Drogue cord pullers: bench one, then write how they work. No document says how a puller is switched (one direction or reversing), how it stops (a set run time or stall current), or what it really pulls on its 5/16 in pulley against the 30+ lb the Build Guide asks. The documents also disagree on the cord's path: Build Guide 7.3 and Routing Guide 12.4 run it through a sealed conduit glued through the transom; BOM 15.7 says no conduits and no transom glands. Bench one motor, time a full wind, measure the pull, then write it in. The stop is settled by item 301: a 64 s run and a fuse per puller. A mount plan is written (2026-09-24, Reference/Cord Puller Mount 2026-09-24.md): the motor on a 3 in piece of 2 x 2 in aluminum angle screwed to the free end of the G10 pad, pulley toward the U-bolts, cord straight down under the pulley edge. Release line, decided by Mike 2026-09-24: the motor pulls the blue 2 mm Dyneema line already on each T8's trigger; pulling it releases the shackle. No fid. The T8s were bought with no swivel. Hull passage, decided by Mike 2026-09-24: no rod. The line runs in a greased PTFE tube sized for it, 2 mm inside, 4 mm (5/32 in) outside, one 20 ft piece for all four, from near the T8, clipped along the outside of the hull, through the hull bedded in 3M 5200 (Mike: 5200, not a cable gland; 7/32 in hole, tube sanded, 5200 fillets both sides, clipped within 1 in of the hole both sides so it cannot work), up to the pulley; at least 12 in of tube outside the hull. Check first that the line pulls freely through 2 ft of the tube, bent 45 degrees (if it binds, 3 mm inside), and that each blue line is about 4 ft long (if short, a 2 mm Dyneema line replaces it). Test first: a scrap tube bedded in 5200 through scrap G10, cured a week, 10 psi of air with soapy water on the far side; 10 psi on a greased tube with the line in it; and the motor pulling the blue line through a full greased tube, at slack and with a realistic load on the shackle (Build Guide 11.1). An EPDM vacuum cap for 5/32 in line goes over the outside end of each tube, the line through a pinhole in it, whipped on behind a heat flare. Links: Left to Buy 2026-09-26 items 97 to 100. Written into the v10.0 guides (Build Guide 7.3 and 11.1, Transom Drogue Box Guide 6, Routing Guide 12.4, BOM 15.7). The mount choice is question 276; the at-sea exercise is question 277. Mike's alternative (2026-09-24), which I think is better: the same angle, 4 in long, through-bolted to the outside face of one of the glassed plywood triangles beside the pad, motor can up, 5200-bedded tube through bare hull beside the triangle (drawing Reference/Cord Puller Rib Option 2026-09-24.png). Mike to pick one before anything is drilled. *Documents: Transom Drogue Box Guide 6, Build Guide 7.3 and 11.1, Electronics plan 4.3 and A16, Compute Bay 12, BOM 15.7.*

215. Victron remote cable length. The five remote on/off cables run from the central node to the five solar controllers, and no document records how far that is. Measure each run against the cable's own length; extend with 18/2 tinned wire if short (item 302). *Documents: Electronics plan 6.7 and A3 entry 22, Wire and Cable Buy List, Box Wiring Sheets.*

219. Wet lab numbers to take on the bench. Loop volume: the Wet Lab uses 2.5 L for the dose and flush but also says about 1.2 L with two stations filled; measure it, then re-figure the 500 mg dose and the flush time. Time the fill and de-bubble at 1.5 L/min (still written as about 60 s). Set the restrictor coil length, (the uxcell PTFE tube went back 2026-10-02, so the coil tube is to pick). The two Taidacent parts bought 2026-09-07 are RS-12V/2S surge modules, not converters; the flow meter's supply is question 282. *Documents: Flow-Through Wet Lab Design 3, 8 and 10; Build Guide 12; BOM 15.11.*

254. Checks from the 2026-09-24 research, when the part is in hand. Each is written in its guide. At v10.5: The Flipsky divider bench check is gone (the divider is always fitted, item 525). The rest stays open.

288. Arithmetic to re-check in Build Guide secs 4 to 6 (found in the v10.0 trim, 2026-09-26; each needs the working it came from, so nothing was changed). (1) Sec 4.6: the solar factor K is 0.72, but its parts (0.88 x 0.95 x 0.92 x 0.96) multiply to about 0.74; the harvest table uses 0.72. (2) Sec 5.3: the overall efficiency from electrical power to thrust is 0.37, but its listed parts (0.55 x 1.15 x 0.8 x 0.97 x 0.85) multiply to about 0.42; a factor may be missing (the controller?). The Routing Guide and Design Decisions R-5.3 use 0.37 too. (3) Sec 4.7 says conserve mode after the midpoint is 200 W; the sec 5.3 modes table lists "doldrums economy 250 W (conserve, post-midpoint)". (4) Sec 4.7's second day figure in each row (11.9 d and so on) is 90 percent of the bank used to empty, not the 90 to 10 percent the heading says: label it. (5) Sec 4.5: the 100/20 controller's clip is given on its input side (about 575 W) and the 75/15's on its output side (about 414 W): put both on one basis. (6) Sec 4.3 gives the emergency island 25 to 32 Wh a day (Compute Bay 5.3); the sec 4.6 hotel table carries 24 for the Pi B island: one figure, or say what each covers. (7) Sec 4.6 skips both the cutter sweep and a cutting campaign in HIBERNATE, STORM and below 30 percent charge; sec 5.3 says that only for the sweep: settle whether a campaign may run below 30 percent (a question for Mike once the working is checked). *Documents: Build Guide 4.3, 4.5, 4.6, 4.7, 5.3; Routing Guide 2.1 and 13; Design Decisions R-5.3.*

289. Bill of Materials figures to re-check (found in the v10.0 trim, 2026-09-26; nothing was changed, since each needs a receipt, an order or a count). (1) Cells: 36 at $100 is $3,600, but the line carries $3,439 paid. (2) Slewing rings: all three ($1,208) sit in Boat 1's wing cost, while sec 15.13 leaves Boat 2's ring out; about $403 of it is Boat 2's (question 287). (3) T8 shackles: $1,701 carried whole; if the box holds eight, about $851 is Boat 2's. (4) "VESC waterproof enclosures (primary + backup)", $80, but Boat 1 has one VESC. (5) The AS5048A angle sensor may be counted twice: a $60 wing pivot sensor in the sensor list, and one on hand in the wing pod line. (6) The nav lights line settled at the v10.3 check ($124: the attwoods went back); the surge parts line still does not add up from the prices written in it. (7) Settled: the Orion-Tr was $56.10 (order tracker). (8) The aluminum oxide grit mixed into the heat-carrying glue: the fine grit bought is 120; the spec is 220 or 320 (Build Guide 5.2). Settled 2026-10-26: the #120 (item 455). (9) The 2 AWG motor leads: BOM sec 15.4 says $41 to buy, the wire list A3 says none. (10) The G10 sheet stock ($719) is not marked bought, though the drogue pads are cut from the 3/8 in sheet. (11) The four SN65HVD230 CAN boards are on hand (bought 2026-08-24), but the Release Node B line still prices a pair (about $16) and the CAN line carries a $40 estimate. (12) The two BME280 boards came in the 2026-09-07 order; the working barometer line still carries a $15 estimate. (13) BOM 15.12's $12 of Belleville washers for the busbar and head-bus terminals looks like 15.2's second M6 pack ($7) counted again. *Documents: Bill of Materials; Wire and Cable Buy List A3.*

281. Drogue boxes, on arrival (not yet received, 2026-09-26). Count them (Boat 1 needs two). Magnet-test the body (steel: do not use it). Measure the wall thickness. Pack one drogue into a box before any metal is stripped, so an unstripped box can still go back; a packed drogue is probably 1,000 to 1,500 cu in against about 990 in the box (both guesses). If it does not fit: the next VEVOR size up (the range goes to 20 x 16 in), not a laid-up box. Size up in fiberglass only: Mike asked 2026-09-28 about the VEVOR 16 x 16 x 8 in STEEL enclosure on Amazon ($73.90); not for this, since painted steel rusts at every hinge and strap hole and cut edge, and epoxy holds poorly on paint. The fiberglass 16 x 16 x 8 in is at Home Depot (VEVOR DQXFSBLG40X40X201V0, $138.82 on 2026-09-25), about 1,400 cu in usable against about 990; Amazon has VEVOR fiberglass 19.7 x 15.7 x 7.9 in (B08ZYJ2QC4, price not checked; check two fit the transom). Transom width up high, where the boxes go, is not in any guide and not published (only the 8 ft beam); measure it before buying a box wider than 16 in. The v9.8 guide's two 22 in boxes suggest about 44 in was once thought to fit, but it was never measured. Boat 1's rudder hangs on the keel, so nothing on the transom is in the way except the quarter U-bolts and the cord puller tubes. The box on order is probably VEVOR's fiberglass 15.7 x 11.8 x 7.9 in (Amazon B091FG96KN). Mike, 2026-09-28: bolt the steel box to the transom and replace it at refits? Claude: it can work, with conditions, but fiberglass is still the better buy. Bolting fixes the glue problem. The risk is rust inside the box between refits: rust swells to several times the steel it eats, and the lid lives in a 1/8 in gap in that steel frame, so rust scale can lock the lid, the one failure that loses the drogue; rusty hole edges also saw the Dyneema hinge and strap. If steel: drill every hole first, then coat the whole box inside and out with epoxy barrier coat and bottom paint the mouth; make the lid fiberglass, not the steel door; bed the bolts and put plastic washers between steel and stainless. Costs against the $65 a box saved: that coating work, some of the hull's barrier coat (item 226 added one kit for the hull alone), and about 20 lb per steel box by Claude's figure (1.2 mm wall assumed, not checked), with the displacement margin already tight (item 2). Mike to decide. Start the Dacron tape salt-water soak now; it takes weeks. *Documents: Transom Drogue Box Guide 1, 3 and 8; Build Guide 3.6; BOM 15.7.* Ordered 2026-09-28 (mail): a VEVOR fiberglass enclosure 19.7 x 15.7 x 7.9 in ($74.01, due Oct 2), the size-up above, and a QILIPSU UL94-V0 16.4 in outdoor box ($82.15, due Sep 30), probably the second. The steel VEVOR of 2026-09-24 is not used.

309. Open questions moved out of the guides at v10.0super (2026-09-27). The guides no longer keep their own open lists; each question below came from one and names where. Where a guide still depends on it, it says "Open:" at that spot. *Electronics, the computer boxes, settings and wire:*

*Rig base, wing can, battery box, drogues, steering and routing:*

*The wing and the slip ring:*

*Lightning, the post, barometer, science, wet lab and Boat 1's route:*

310. Numbers that disagree, found at v10.0super (2026-09-27). Each needs a check, a receipt or Mike's word; none was changed.

313. What the deck solar change leaves open (2026-09-28). The deck array drops from 1,675 W on paper to about 1,400 W.

338. The lightning copper through the deck (the junction and the pickup below the deck are written in, 2026-10-01). Also open since the junction became a bolted crossing: where the post bar, the spark-gap bar, the battery negative wire and the far spurs land (for example taps drilled in the cross bar beside the crossing, as sec 6.1 does); the cross bar layout at the bulkhead settles it (Lightning Ground System Guide 5.3, Open line). The copper above the deck: decided 2026-10-01 (Mike: "drop it"), written in the same day (see the Closed 2026-10-01 list): no copper above the deck; the main bolts carry the strike and the trunk picks up a side bolt below the deck. Drawing: Reference/Item338 Copper Pickup 2026-09-30.png. The junction, decided by Mike 2026-09-30: with the keel block gone (item 344) it has two branches. One bar runs across the bulkhead to both hull sides (two sticks lapped 4 in end to end, two bolts, as the post run), nearly level, 5 to 15 degrees downhill toward each side, then curving onto the hull face (8 in radius or more) to its exit bolt. The trunk comes straight down and crosses it face to face, and the crossing is held by ONE 1/4 in silicon bronze bolt through its middle with a wide washer each side, both faces sanded bright with No-Ox-Id; meter it with the battery-and-bulb check (Lightning Guide 8.1), near 1/1000 V at 2 A (inferred). No plate is needed (Mike has no 4 x 4 in copper). The near-square turn is allowed: NFPA 780's 90 degree and 8 in limits apply to bends in a bar, not to a bolted joint where current divides. Washers, not bought: stainless 1/4 x 1 in fender washers on Amazon (https://www.amazon.com/Stainless-Steel-Fender-Washers-pcs/dp/B00AGK8WUY, price not checked; fine here, since the washer only clamps), or silicon bronze 1/4 x 1-1/4 in from Fair Wind ($0.79, 3/64 in thick, https://fairwindfasteners.com/products/silicon-bronze-fender-washers) or Green Boat Stuff (about $1.10, 1/16 in thick, https://www.greenboatstuff.com/sibrflwa1.html). Also left (found 2026-10-01 while writing it in): (a) how the two 1/4 in pickup bolts are held (through the tripled middle bulkhead and both angles, or into holes tapped in the 1/4 in leg), their length, and which side bolt is used; (c) the bond wire count: Lightning Guide 3, 6.2 and 10.1 say eleven, one wire each, but the can and the rudder stock now get none, and the Wire and Cable Buy List A5 says ten; (d) the bar total: BOM 15.2 says about 45 ft, the Lightning Guide about 40 ft; the trunk now starts below the deck, so measure it; (e) Lightning Guide 8.2 meters the other bolted joints but not the new pickup joint; add it when the pickup is drawn; (f) done 2026-10-08: the concept drawing Wing_Can_Fabrication_2026-09-24 and its script are in Archive, and the bond stud note is gone from the plate 3 drawing. *Documents: Lightning Ground System Guide 5.2, 5.3, 6.2 item 1, 9.2; Rig Base Two Plate Design secs 3 and 5; Wing Can Spec Sheet; the shop sheet (item 343).*

341. Figures to re-work for the XXS mast (found at v10.1). v10.1 scaled the mast-break figures by about 1.24 and marked them "scaled"; these still need working: (1) Design Decisions R-3.3: the slewing ring bolt joint's margin over the mast's plastic hinge falls from 1.47x to about 1.19x (inferred, 1.47 x 22,400 / 27,700); (2) Design Decisions R-6.9 and Build Guide 6.9 keep the Schedule 160 shedding band (22,000 to 33,000 ft-lb) beside the XXS mast-break figure; (3) the plain 3/4 in can lip runs just over 304's yield at the band top, carried by the 16 lip gussets, not re-checked; (4) the stability figures (R-1.3) were worked with about 10 lb less aloft; the inclining test settles it. *Documents: Design Decisions R-1.3, R-3.3, R-6.9; Build Guide 6.9; Wing Can Spec Sheet.*

342. Steering checks left after v10.1. The port side, the 13 in station, the 16 in cut, the stop blocks just past the actuator's ends and the rear mount as built are written in. Left: whether the blade clears the hull and prop at 28-1/2 degrees (hold it there before the blocks are bolted down); whether the cockpit floor has room out to about 30 in to port; and redraw Reference/Steering Actuator Top View 2026-09-28.pdf Section B, which still shows the old angle bracket, once the rear pin's height above the floor and its distance forward of and to port of the stock are measured. *Documents: Steering System Handbook 3 and 4.*

1C. Waiting on somebody else's reply

25. Dacian at Electrodacus: one optional question. What the SBMS0 reports with the XT1 probe unplugged. The Battery Box Part 10 bench check measures it anyway, so send a mail only if that reading is unclear. Item 166 made the other two questions moot. *Documents: Battery Box Building Guide Part 8, BMS Notes.*

8b. Two shops. The mast weldment has no fabricator. The wing can needs a shop quote once the Spec Sheet blanks are filled (item 8a). The metal for both is on hand and both mill certs are in (item 332, written into the guides 2026-09-29). Shop leads in the Tulsa area and every metal job by package: Reference/Fab Cut Weld Work List 2026-09-29.docx (2026-09-29). *Documents: Wing Can Spec Sheet, BOM 15.6.*

89. Deliveries.

*Documents: the order tracker, BOM.*

96. Returns, with their windows. Now kept in one place: the "Send back for refund" tab of BOM v10.5 Order Status.xlsx (built 2026-09-26 from the mail). First deadline: the four KSD301 discs, 2026-10-04; then the bare MOOKEERF roll (about 10-08), the two Talentcell packs (about 10-21), the two 5 A MPPT boards (about 10-23), the Ecoflex pint (about 10-25), the three DG7512 boards and the heater pads on arrival, and the 5 in acrylic dome (drop off by 10-12). Found in the mail 2026-09-26: the second FE-P was cancelled 2026-09-21 before it shipped and the carbon brush pair was cancelled by the seller, so neither needs a return; the Lensun panels were cancelled and $334 refunded; the attwood lights went back, $71.20 refunded. Found 2026-09-30 (mail audit): the SmartSolar 100/20 story is corrected (Mike, 2026-09-30): of the two 100/20s ordered 2026-09-07, one came and the other, delayed, was cancelled 2026-09-29; its replacement (Amazon 112-8872850-2808228, $74.25 in points) shipped 2026-09-30 and arrives Oct 1. It is the second 100/20, not a third: keep it. The two-100/20s-then-three-75/15s layout stands. The VEVOR 16 in box was too small (Mike, 2026-09-29): VEVOR refunds on photos of it destroyed, nothing to ship. The SUPREMETECH 5 in dome is refunded ($16.93, 2026-09-30). *Documents: the order tracker, BOM (15.6 returns line, 15.8 FE-P line).*

38. Return the weather pod parts bought for the post: any pod housing or QwiicBus parts. *Documents: the order tracker.*

138. Fix Supply brass: check the certificate covers these fittings. The tracker logs Fix Supply's 2026-09-09 answer for order 000166489: certificate COCGSCIBRZTHDFTG-02, SCI bronze threaded fittings to ASTM B584 / B62, UNS C83600, which is a red brass. If it names the two 1 in tees and the two 1-1/2 x 1 in reducer elbows, write C83600 into the BOM and install them; if not, buy bronze. They stay out until then. *Documents: BOM 15.11, Flow-Through Wet Lab Design 4.*

261. Spain: permission for the boat to come into and leave the Canaries. Researched 2026-09-24: Reference/Spain Autonomous Vessel Permission 2026-09-24.md, whose sec 7 is the step list; the steps are written into Boat 1 Route sec 5 and the Checks file, and the permission itself is still to get. The short of it: written permission from the Capitanía Marítima de Las Palmas (Spain's harbor master office there), once to enter Spain's waters and once to leave port, asked in Spanish, at least 48 hours ahead by law but in practice months ahead: have it before leaving Brunswick. The boat cannot clear itself in or out, so a Las Palmas ship agent or PLOCAN (Gran Canaria's ocean research center, which handled Saildrone in 2019) gives the Spanish address and does the paperwork. Expect a liability insurance question (Spain's floor for leisure boats is EUR 336,567). Steps: October, email PLOCAN and write to the Capitanía (+34 928 468 262); by mid-October, settle the flag and papers (Build Guide 11.5); November, insurance; by December 1, file the entry application; December, book the tow in. Biggest unknown: whether the boat may sail itself inside Spain's 12-mile zone or must be towed from outside it. Not researched: Portugal's rules, since the route passes inside Portugal's 200-mile zone near the Savage Islands. *Documents: Boat 1 Route; Build Guide 11.5.*

1D. Money

121. Left to buy. Rebuilt 2026-09-26 with a link for every item: Reference/Left To Buy 2026-09-26.md (and .docx); the total is at the top of that file (about $5,320 on 2026-09-28, after the deck solar change and a pass against the order tracker, whose Buy list tab now agrees; the deck panels and their tape are $3,300 of it), plus shop work by quote and the items that wait on a check. It replaces the 2026-09-24 list, now in Archive. Still waiting on something: the mast weldment and wing can (8b), the Plate 3 hinge stop welding, the waterjet order (haul-out), the deck solar and its tape (the four deck checks of Build Guide 4.4), the grit (86b), the release trunk cable (17), the bridle hardware (81). Before buying the Iwaki pump (bought 2026-09-28, $188.29), read the NRD manual for a minimum-flow note: it will run at 30 percent of its free flow. *Documents: Left to Buy, BOM.*

109. What is left of the 2026-09-15 buy list. To buy: a second 50-pack of M6 (1/4 in class) 304 conical washers ($7). To log: the Thomson MD part and price (forward Thomson's acknowledgement) and what the S1eX cost. Done: the foredeck fisheye (Hanwha XNF-8010RV, bought 2026-09-30, $132), Lasdrop, S1eX, cord pullers, tinned 18/4, wet lab PVC, the MOTU M2 (ordered), and the CAN boards (four SN65HVD230 on hand). *Documents: BOM, the order tracker.*

129. Money with a clock.

*Documents: the order tracker, BOM.*

139. Services and fees are on no list. Insurance (hull, liability, wreck removal); the flag or registry entry and the USCG notice; Iridium airtime for both modems (about $60 a modem to unlock, plus a plan); transport to the launch port, haul-out and launch; a crane or travel-lift for the 30, 60 and 90 degree heel test; a chase boat and a shore station; the lake power sweep and the inclining test; the PMI or hardness test; the 2205 fabrication with its dye-penetrant report; welding the twelve bolt heads to the rail. The BOM carries a 12 percent lump with no lines under it. Price these or mark them out of scope; Build Guide 11.2, 11.3 and 11.5 name most. *Documents: BOM.*

140. Test gear the launch gates need. On hand: the insulation tester (bought 2026-09-21), the 0.1 g scale and a come-along; the duckbill manometer is a vinyl tube on a yardstick. No pull tests, so no load scale (Mike, 2026-09-28). The 3M 2091 P100 filters are on hand; the respirator and HEPA vacuum are off the buy list (Mike, 2026-09-26). No thermal imager: Mike dropped it 2026-09-26. *Documents: BOM 15.1.*

142. Charges nobody has explained. DHL $270.84 (waybill 1296045575, invoice D35180194, a shipment of June 5); UPS $49.73; a $784 PayPal payment to Hunan YLWL on 2026-08-19. If any is boat parts, it belongs in the cost reconciliation. *Documents: BOM, the order tracker.*

224. The second relay module is probably on the shelf. Item 197's second 8-channel relay module (about $15) is on the BOM as to buy, but the tracker logs two HiLetgo 24 V 8-channel modules bought 2026-08-16 and 2026-08-18, and Electronics plan sec 8 lists two relay modules the node no longer uses. Check the shelf before buying; likely nothing to buy. Also likely on hand, per the tracker: the two 3/8-16 x 5 in 316 mast-socket bolts (Bolt Depot 2624658, check the length) and the sealed fuse holders (Mike's 2026-09-21 notes). *Documents: BOM 15.8, Electronics plan 8.*

227. Parts bought with no line in the design. Each needs a job written into the BOM, or it goes back. Mike says what each is for:

*Documents: BOM, the order tracker.* ---

Part 2. Questions for Mike

2A. Real calls

557. Four battery probes, not six (Mike, 2026-11-09: "Using 4 probes in batt box"). Two per 16-cell stack, one on each of the stack's two middle groups (where heat has the farthest to travel); the two end-group probes are dropped (Claude's placement, from the guide's own reasoning). The trunk is unchanged: Mike's 3-conductor 20 AWG cable through its own PG9 gland on the battery box aft wall (A9 entry 3b) straight to central node entry 21, red to T23, black to T24, data to T25 (D11, with the 4.7k to 3.3 V), never through the BMS box (Central Node box plan). Four probes on the trunk: 12 joints instead of 18. The joints (WAGO 221-413 lever connectors, Claude's pick, or the guide's crimp splices): Mike picks when the probes go in (2026-11-09: "will figure that when we install them"); do not ask again before then. About 10 probes on the boat in all (Mike, 2026-11-09): all to the central node. Chain 1 keeps only the 4 battery probes (one wet or shorted probe takes down its whole chain, so the battery trip stays alone); chain 2 (D12, split gland 17 port d, 22/12) takes the other six or so. Where they go and how they join: Mike picks later ("You don't need to notate it for now"). The Central Node box plan now labels chain 1 "4 battery probes" and chain 2 "other probes" (2026-11-09). At the next write-in: Battery Box guide Part 8 (probes), Electronics plan A3 entry 21 and A9 entry 3b ("six"), Bill of Materials (DS18B20 line), System Settings Sheet sec 9 (probe names). *Documents: as named.*

556. SBMS0: the stored settings need one power cut, and the end-of-charge voltage lowered so the battery percentage resets to 100 (Claude, 2026-11-09, from Mike's "Cant get to the 12 pin cable to reset", "Can't get to either end", "Power may never get cut"). (a) Power cut. The SBMS0 runs only off its cell ribbon, straight from the cells, ahead of the battery switch, so it may never lose power. Parameter Settings and Advanced Parameter Settings (type, cells, capacity, parameters 29 and 30, the end-of-charge voltage) go into its battery chip's memory and load only at power-up (Reference/SBMS0 v03d Manual.pdf pages 6 and 30). Device Settings (shunt values, UART, EXTIO types) save to flash with Save device settings and work at once (inferred from page 32: UART on turns WiFi off at once). Neither ribbon plug can be reached in the box as built (Mike, 2026-11-09). Never cut power by lifting one tap wire: the other taps can keep the board half-powered (Claude's reading of how the chip is fed). Lifting one tap does not work (Mike, 2026-11-09: "disconnected gray wire from pos batt, screen still on (3 minutes)"). The plan of the same day (lift the SBMS0's gray W8 ring at pack plus) failed: the board keeps running, most likely fed from W7 through the body diode of its own cell 8 balancing switch and balance resistor, a diode drop below 23 V (Claude's reading of the schematic, manual page 44; the same happens at the bottom through W1 if W0 is lifted). Claude's earlier call was wrong. Only pulling a whole ribbon plug cuts it. Gray put back. Open: neither plug can be reached (Mike); the manual says the chip may sleep and drop power for about a second after 4.5 h with no current it can see (page 24), which might load the stored values by itself (guess). Boat sheet step 7 now says pull the plug. DONE (Mike, 2026-11-09: "Got it rebooted from batt terminals, all off, then black and grey on (powered up) then the rest on again"): every SBMS0 tap ring lifted at the battery, then black and gray back on (the board powered up), then the rest; the stored settings (type, 8 cells, 1256 Ah, parameters 29 and 30, end-of-charge 3.44 V) load at that power-up. The question of having Pi A work out the battery percentage itself is dropped: no longer needed. (b) End of charge. The SBMS0 sets its battery percentage to 100 only when the highest cell reaches the end-of-charge voltage, 3.53 V by default for type 1 (manual pages 23 and 26); it starts at about 50 percent. The five chargers stop at 27.6 V, about 3.45 V a cell, and the balancer holds the groups within about 0.01 V, so the highest cell likely never reaches 3.53 V and the percentage never corrects (inferred). Load shedding runs on that percentage (Build Guide sec 4.2). DECIDED (Mike, 2026-11-09: "yes 3.44"): end-of-charge voltage 3.44 V in Advanced Parameter Settings (its number on the list not known; the screen's help names each), set before the one power cut; on the SBMS0 boat sheet, step 2. At the next write-in: System Settings Sheet sec 1 (SBMS0 rows) and the Battery Box guide setup steps. Boat sheet renamed 2026-11-09 (Mike: "add to pdf, remove shunt wiring (done)"): Box Plans v10.5/Battery Monitor Setup v10.5.pdf (source _v105_work/box_plans/sbms0_setup/Battery_Monitor_Setup.html) replaces SBMS0 Setup and Shunt Wires v10.5: the SBMS0 setup steps and signs, plus the JK balancer and the five Victron chargers over Bluetooth; the SBMS0 WiFi steps came off again the same day (Mike: "remove sbms0 wifi from pdf"); the battery box closing note came off too (Mike: "remove closing batt box bit"); Victron battery voltage 24 V added to the charger steps (Mike, 2026-11-09: "yes add 24v"): each charger detects 12 or 24 V once, at its first power-up ever, and keeps it (Victron manual, MPPT 75/10 to 100/20, sec 3.1), so a first power-up on anything but the 24 V pack leaves it wrong; write into System Settings Sheet sec 1 at the next write-in; the shunt wiring left the sheet (built; recorded in Battery Box guide Part 8 and Electronics plan 7.6, whose pointers to the old sheet came off). *Documents: System Settings Sheet sec 1; Battery Box guide setup steps; Box Plans v10.5/Battery Monitor Setup v10.5; Build Guide sec 4.2.*

551. Wing actuator plug: buy it ready-wired instead of crimping its pins? (Claude, 2026-11-09, from Mike's "huh?" on the crimper row). The DTM 4-pin plug at the wing actuator needs its size 20 pins crimped onto 18 AWG wire with a special crimper: small, fine hand work, which Mike's 2026-11-08 rule says to avoid. Claude suggests a DTM 4-pin plug pair sold ready-wired (pins already crimped on short wire tails), joined to the actuator wires and the cable with butt splices like the slip ring joints. The crimper then comes off the Buy list; the MUYI kit Mike bought in October is not used. Waiting on Mike's yes.

552. Rig base edge bolts: are all 36 in? (Mike, 2026-11-09: "What's this for?" on the "6 more" bolt row). The rig base has 36 edge bolt holes (Rig Base sec 5); the 30 old hatch bolts fill 30, and the Buy list has 6 more 3/8-16 x 2 in 316. Mike said on 2026-11-02 the edge bolts are in, but not whether all 36 are. If all 36 holes have a bolt, the row comes off.

536. The Nucleo solder links clash with Mike's no-fine-work rule (Claude, 2026-11-08). Compute Bay Plan sec 10.2 has four tiny solder links removed from each NUCLEO-G431KB at the bench (A4 and A5 from D4 and D5, A2 and A7 from the USB serial link), allowed under Mike's 2026-09-27 one-time bench soldering rule. On 2026-11-08 Mike said he cannot desolder or do fine hand work ("I can't decenter like that, it's not possible"). Three boards on hand need it (central node, Release Node B, wet lab). The four, from ST's manual UM2397 Table 9 (all on by default, on the chip side despite the manual saying bottom): SB1 and SB12 (USB serial link to PA2 and PA3, Nano pins A7 and A2), SB2 and SB3 (PB7 and PA15 to the A4 and A5 pins). Each is a tiny 0 ohm resistor, about 1/16 x 1/32 in. Marked photo: Reference/Nucleo G431KB Solder Links 2026-11-09.png; manual: Reference/ST UM2397 NUCLEO-G431KB User Manual.pdf. Why, and an error found (Claude, 2026-11-09, from the manual): (1) SB2 and SB3 matter: the central node's pin map (Compute Bay 10.2) puts release gates 5 and 6 on A4 and A5, and with SB2 and SB3 on those pins are joined to the I2C data and clock lines (PB7 on D4, PA15 on D5), so every I2C message would also drive gates 5 and 6. (2) The plan is wrong about A2: by ST's table, A2 reaches the chip (PA3) only through SB14, which is OFF from the factory, so A2 is connected to nothing; taking off SB12 alone would not make the horn on A2 work (it would also need SB14 closed, more fine work). No-solder fix, Claude's pick: move the horn to A7 (PA2, the spare); PA2's only extra load is the USB chip's serial input through SB1 (inferred harmless), so SB1 and SB12 can stay. Check the wet lab box's pin map for A2, A4, A5 the same way. Release Node B's three pins are not yet picked: pick pins clear of A2, A4, A5, A7, D5, D12, D13. No-removal pin map, proposed 2026-11-09 (Mike: "How about a work around so nothing needs removed"): leave all links as shipped and never use A2, A4 or A5 (PA5 and PA6 set as floating inputs, as the manual says). (a) The post wind meter (Calypso CMI1018) is only listened to, on D0: it sends on its own at the data rate set once with Calypso's PC app (inferred from the manual's Data Rate setting), so D1 is freed. (b) The horn moves to relay channel 8, a spare channel already driven by the expander, so relay 13 and its pin are not needed. (c) Release gates 5 and 6 move from A4 and A5 to D1 and A7. A7 (PA2) also reaches the USB chip's serial input through SB1; if that input has a pull-up, the MOSFET board's own pull-down still holds the gate off at power-up (a guess: about 0.7 V with a 10k pull-down against a 40k pull-up). Native pins used: 19 of the 19 usable, none spare. Release Node B: pick its three pins clear of A2, A4, A5, A7, D5, D12 and D13. Wet lab box: check its pin map the same way. DECIDED 2026-11-09 (Mike: "yes"). One change in doing it: the horn stays on relay channel 13 (its wiring unchanged) and its coil moves to the expander pin that was channel 12's (PB3), so channel 12 has no driver; channel 8 stays spare. Written in: Compute Bay Plan 10.2 and 11 (and its Word file), the Central Node box plan (all pages), the order tracker's horn row. To write in: Electronics plan sec 4 and A3, System Settings Sheet (channel 13 and the wind meter), Bill of Materials (the horn line), Glossary, Instrument Post Guide (wind meter wiring) (Box Wiring Sheets, Node Boxes Explained and the box plans cross-check done 2026-11-09); the wet lab box, checked 2026-11-09 (built): it used A2 for valve 1's second position input (opto output 3), and A2 reaches nothing, so that one wire moves from the carrier's A2 screw to its A7 screw and the firmware reads A7 (A4, A5 are not used; done in the Wet Lab Box plan; if its links were already taken off, nothing else changes); pick Release Node B's three pins clear of A2, A4, A5, A7, D5, D12, D13. Was: SB2 and SB3 on the central node only, unless a pin map can move gates 5 and 6 to other native pins (none free once the horn takes A7; not worked out). Ways out: someone else does the 12 links at the bench (Ken bought the wet lab's board), or the pin maps move off A2, A4, A5 and A7 (a software and drawing change, if spare pins allow; not checked). Also noted: the G431KB stays the pick for Boat 2 (on-chip CAN, the Nano carrier's shape, the same software as Boat 1); its tariff is on any US seller. *Documents: Compute Bay Plan 10.2; the three box plans.* At v10.5: The central node's pins and the solder links left as shipped are written into the v10.5 guides. Still open: Release Node B's three Nucleo pins.

528. Boat 2 only: a more reliable drogue release. DECIDED 2026-11-08 (Mike, 2026-11-08: "Not for boat 1, but for boat 2 i think a better plan could be more reliable", then "One CAN one some other comm? Release B powered directly from backup batt? Either Pi can trigger both."). Boat 1 keeps the two chains as built: horn A from the central node, horn B from Release Node B. Mike's Boat 2 plan: (a) chain A on CAN, chain B on a different kind of link, so one link fault or one software bug cannot stop both; (b) Release Node B powered straight from the backup battery, not through the main bus board and the backup converter; (c) either Pi can trigger either chain. Claude agrees (opinion). It is item 494's way (Mike's Nov 1 wish for Boat 1, dropped only because a horn turned out to need 12.5 A, not 25 A), with two gains: either Pi reaches B directly instead of Pi A handing over to Pi B, and a non-CAN link removes 494's problem of a backup-side node tying the two batteries' grounds together on the house bus. Notes for the design: B's link must be isolated, since B and Pi A sit on different batteries (for example an isolated RS-485 line, bought ready-made, with both Pis on it; inferred, not checked); the backup board's 30 A main fuse covers one 12.5 A burn plus Pi B, Iridium B and pump 2 (about 3.5 A), so 494's 40 A fuse is not needed; B's standby draw comes off the backup battery (a guess: 0.3 to 0.6 W, 7 to 15 Wh a day, against 70 to 220 Wh a day from the panels in winter), so B's logic should wake only when a release is coming, from either Pi. DECIDED 2026-11-08 for Boat 2 (Mike: "yes for boat 2, i think power the relay from batt 2 always on, and power the nucleo switched somehow to keep it off unless used"). Power split: the burn path (the enable relay's contacts and the release bus) is fed from the backup battery all the time, on its own breaker or fuse on the backup battery board; it draws nothing at rest, since the enable relay is open and the MOSFET boards take their supply from the dead release bus. The logic (the 24 to 5 V converter, so the Nucleo, the CAN or other link parts, and the enable relay module's own supply, whose board lights would otherwise stay lit) is off until a release is coming. How it wakes (Claude's pick, standing unless Mike says otherwise): one relay channel per Pi, the two contacts side by side (either one closes the feed) on the logic feed at Release Node B; a relay contact keeps the two batteries apart, so Pi A on the main side can wake it too. Each Pi closes its relay, waits for the node to start, sends enable then release, then lets go. With the logic off, the enable relay cannot close, so an accidental release needs one more fault than on Boat 1. A second switch on the burn path (Mike: "or maybe switch both"): Claude's view is no, since the enable relay already switches it, draws nothing open, and a second switch is one more 12.5 A part that can fail and block a release; Mike: "keep that in mind for boat 2, consider boat 1 settled". Settle it in the Boat 2 design. Boat 1's Release Node B is settled as built (Mike, 2026-11-08). *Documents: Boat 2 notes only.*

501. Box plans cross-check: questions for Mike (Claude, 2026-11-01). From drawing the 16 box plans (Box_Plans_v10_4a/Box Plans Cross Check v10.4a, page 1). Claude's suggestion after each. (a) Release switches may be too small: the "600 W MOS" boards on both release nodes are sold as about 10 A, 15 A with a heat sink (listings for that name; the exact board is not known), and a horn draws 12.5 A for up to 60 s. Read the board's listing or label; if 10 A, a heat sink or a bigger board on each horn channel. (b) Pi B's carrier may not stand up in its box: the CM5 IO Board is 3.54 in across and the box 3.9 in deep outside; the X1500 is Pi-sized and fits; the docs disagree on which carrier is Pi B's (Compute Bay 4.2 against BOM 15.8). Look at the shelf; if Pi B's is the IO Board, it lies flat with its own cooling pad. (c) The switch box's 54 V supply is too tall for the switch's rail (4.93 in standing on a level rail, in a 3.9 in deep box): yes or no to its own short upright rail on the end wall, as the plan draws it. (d) The BMS box likely does not fit the battery box's aft wall (about 7 x 3 in of bolt room under the glands; the three boards need a box of about 8.7 x 6.7 in, Claude's estimate): look at the BMS box on hand; if bigger than about 7 x 6 in, it goes on the bulkhead beside the battery box. (e) Pump 2's cutoff: the Smart BatteryProtect's remote must be closed for pump 2 to run; wired to Pi B as written, a dead Pi B would silence pump 2, against item 491. Yes or no: Pi B's side only opens the loop (a normally closed contact), so it can stop a stuck pump but never has to hold it on. (f) The backup converter's 17 ft of 12/2: Victron asks about 7 AWG at 16 ft; 12/2 drops about 4.6 percent at its full 21 A in, so its own low-voltage cutoff trips early; and with its clearances it needs about 13 in of height, more than the 12 in board. Yes or no: mount it beside the backup battery, so its input run is short and the 12/2 run is on its steady output side. (g) The watchdogs' serial lines are 5 V into 3.3 V Pi pins (WD-A to Pi A, WD-B to Pi B; the backup battery reading uses WD-B's): yes or no to two resistors on each Nano TX line, the same 15k and 22k pair as the safe-mode wire (kit on hand). (h) The Iridium coax cannot pass a PG7 (a premade jumper with an SMA and an N plug): yes or no to a spare Altelix split gland port on each Iridium box. (i) Iridium A's 16/2 power is listed in a PG7 (A11); every other 16/2 goes in a sealant-filled PG9 and an oval 16/2 does not seal in a PG7: drawn as a PG9 in the plan unless Mike says otherwise. Mike's answers, 2026-11-02: (a) "which ones?": answered in chat (the four boards that fire the drogue lid horns: central node release channels 1 and 2, Release Node B's two). Mike's screenshot of the order (2026-11-02) names the board: GODIYMODULES XY-GMOS-002, "2 Pcs High-Power 600W MOS Tube FET Trigger Switch Drive Module PWM Control DC 4V-60V", Amazon B0DWRW4YHZ, bought 2026-08-24, two MOSFETs in parallel, "continuous current 10A at room temperature ... Under the condition of auxiliary heat dissipation, the current can reach 15A", trigger 3.0 to 24 V high. A horn draws 12.5 A. Settled 2026-11-02, no change (Mike: if the wire burns in 1 s there is no ill effect; a wet wire may take 15 s, so a 10 s stop could cause a failure; and the boards are one-time use, so a board that burns after the strap is cut costs the mission nothing): the burn keeps its full enable window and the boards stay as bought. Note the trigger floor: 3.0 V, against the Nucleo's 3.3 V high (just above it). (b) "fits": the Pi B carrier fits; closed. (c) "fits": the switch box supply fits on the switch's rail as the guides say; closed, the plan redrawn. (d) "it is mounted on batt box side", then "side, as said" (2026-11-02): as built, the BMS box is bolted to a long side wall of the battery box, not the aft end wall the guides name (Electronics plan A4, Battery Box guide Parts 4 and 8, which kept it off the long walls because the nuts there sit against the padding and the cells; Mike, 2026-10-03). Write the as-built spot into A4, A9 and the Battery Box guide at the next write-in, with the side and height once known; the BMS Box and Battery Box plans now show it on a side wall (2026-11-02). (e) "I don't think we ever want to kill a bilge pump": DECIDED, no remote stop on pump 2: the BatteryProtect's remote keeps its factory wire loop and nothing from Pi B or shore stops pump 2 (this drops A10's "its remote on/off input is wired to Pi B, so shore can stop a stuck pump 2"). DECIDED 2026-11-02 (Mike: "drop battprotect, was silly"): the Smart BatteryProtect is dropped; pump 2 runs from its 5 A breaker on the backup battery board straight to the Ultima switch and the pump, with no cutoff, and the 1.5KE33CA stays across its pair at the board. Not bought, so nothing goes back; the tracker's Buy list row is marked dropped. Drawn in the Backup Battery Board plan. (f) "yes": DECIDED, the backup converter mounts beside the backup battery (the Dyness), its input run short, its 12/2 run of about 17 ft on its output side to the backup-fed bar. (g) "explain please", then "resistors seem a macgyver like fix. anything more standard?": needed on WD-B's send line to Pi B only (it carries the backup battery reading); Pi A's heartbeat runs Pi to WD-A only. DECIDED 2026-11-02 (Mike: "i think the converter board sounds more reliable"; Claude agreed): WD-B's serial line to Pi B, both wires, runs through one HiLetgo 4-channel logic level converter board (10-pack on hand, bought 2026-10-06), 5 V side to WD-B, 3.3 V side to Pi B, in the Pi B box; it also gives Pi B's 3.3 V send a clean 5 V at WD-B. Pi A's line needs nothing as drawn. Drawn in the Pi B Box plan; at the next write-in: Compute Bay 4.2, Electronics plan A2, BOM 15.8 (the shifters are no longer "not used"). (h) and (i) "as needed, no reason to write it up": done at fit-out as needed; closed, nothing to write in. Written into the box plans (Network Switch Box, Backup Battery Board, Pi B Box) 2026-11-02; at the next write-in: Electronics plan A2, A6a, A10 and 7.6, Compute Bay 4.2 and 5.2. *Documents: Electronics plan A2, A4, A6a, A10, A11, A15, 7.6; Compute Bay 4.2, 4.3, 10.3; BOM 15.8; Battery Box guide Part 8.* At v10.5: Written into the v10.5 guides. Still open: which long side wall the BMS box is on, and how high.

482. Whole-boat wiring review: more pass-throughs, a few mistakes, parts doing nothing (Claude, 2026-10-31, from Mike's "Please do an extremely thorough deep dive into all boat wiring and box wiring and look for mistakes, inefficiencies, opportunities for improvement, opportunities for simplification"). DECIDED 2026-10-31: (a) to (f) and (o), all yes (item 486), written in 2026-11-01. Still open: the rest, except (p), dropped 2026-11-04 (item 519 (g)), and (y), already how Boat 1's hub box is built (item 519 (c)). Read-only review of every box and run in the v10.4 guides, in four parts (central node, compute area, power side, stern and deck). Full detail, sources and how sure each point is: Reference/Wiring Review 2026-10-31.md. Nothing is written into the guides yet; each call below waits on Mike's yes. Central node entry numbers are the new ones (item 481). Same kind as the aft junction fix (Claude's pick: yes to (a) to (d)): (a) Bilge straight to the node: the pumps sit beside the node (Build Guide 3.6), but their two switch-ons go about 12 ft aft on the channel 6 16/2 and come back on the bilge 18/4, and the two running signals go aft on the 18/4 and come back on trunk cores 6 and 7; the aft junction does nothing to them. Run the 18/4 straight from the node to the pumps (red ch 6 fuse, white ch 12 fuse, black and the 4th core to opto inputs 1 and 2), one PG7 at the node. Drops the channel 6 16/2 run (node entry 9), aft junction gland 3, four blocks, split gland port c, trunk cores 6 and 7, and the black wire re-marked red "P2 ON". Sleeve and label the two running cores P1 RUN and P2 RUN (they carry 24 V; true today too). (b) Whites without their relay: the 30 A light relay switches 1.5 W of whites (about 0.07 A at 24 V) and its own coil draws about half that; land trunk cores 8 and 9 (channel 7, after its fuse at the node) straight on the whites' converter. Drops the relay module, F3 and its holder, two blocks and the trigger-jumper step. (c) Bow lantern fed from the node: today its feed goes node to stern (F4 and its converter in the aft junction), then the length of the boat to the bow; put F4 and the bow converter at the node and run the bow cable straight forward (a 16/2 offcut in a PG9 is then fine, no round cable needed). About 20 ft less cable (guess). (d) Fuse channel 3 at the node: it fails ON and leaves the node unfused, so a short in its run to the aft junction trips the node's 15 A breaker and comes back at every reset, the lockout that got channels 4 and 9 their fuses; move F2 (and F4, with (c)) to the node right after the contact. (e) Then drop the aft junction box altogether? (a layout change.) After (a) to (d) the box holds only joints: the always-on jumper feeds just the wind meter's Pololu (0.25 mA), and the trunk carries wind, encoder A and the whites. Run the post lights cable, the wind meter cable and encoder A's lead straight to the node, as the horn pair already runs; the whites converter, the stern light fuse and the wind meter's own Pololu move into the node (the meter then switches on and off with the Nucleo, which ends the unpowered-pin worry of item 468 (e) with no added part). Goes: the box, its 5 holes, about 24 blocks, the switch-box jumper, the channel 3 and channel 6 runs and the trunk; the node takes about four small round cables in one split gland, about the same hole count. Option inside it: the horn rides the post lights 18/4 (stern +, whites 12 V +, horn +, shared 0 V), so the post carries 4 cables, not 5. Costs: node box room (not laid out yet), post cable tails about 20 ft instead of 6, and the Instrument Post Guide's "land every post cable at the aft junction" goes. Lightning: almost nothing lost (the box has no surge part on the post lines today). Claude's opinion: yes. Mistakes (Claude's pick: fix each): (f) The charge stop is a loop: the positive goes from the 1k at the bus board to the node, through channel 8's closed contact, and back to the yellow-wire strip, so one broken wire, loose screw or dirty contact anywhere in it floats the yellow line and stops all five chargers (Build Guide 4.1: "floating they stop"), against the rule that every failure leaves the boat charging. Fix: the 1k goes straight from the + bar to the yellow strip on the bus board; one wire from the strip to the node, through channel 8's normally OPEN contact to 0 V. Coil on still stops charging; a dead node, a broken wire or a loose screw means charging. The 1k then carries about 29 mA (0.8 W) during a stop, so it must be 2 W or bigger: the fifteen 1k 2 W metal-film resistors bought 2026-09-01 (order log, for the old UV-C plan) do it, nothing to buy. (g) Release Node B's two fire runs have no named cable, and its PG7 glands cannot take 14 AWG pairs: use one piece of the 14/4 left on its roll in one PG11, like path A (4 holes to 3). (h) The Iridium boxes' coax comes as a premade SMA-to-N jumper, and the SMA plug will not pass a PG7 seal: one 4-port split gland per box for the coax and the RockBLOCK cable (3 holes to 2); the boxes are not bought yet. (i) Starlink's power pair now comes from the deck into the node with no ferrite; add one (on hand) and a row in Electronics plan 7.5. (j) 24 V rides in the trunk beside the Nucleo's own 3.3 V and pins D0, D1, D6; one crush kills the node (steering, releases, battery trip). (a) and (e) end it; if the trunk stays, keep 24 V out of it. (k) Encoder A and the Ewellix pot take 3.3 V from the Nucleo's own rail out to the rudder; a short there holds the node dead. Feed them from a spare Pololu D36V6F3 (two bought, no job) behind a small fuse. (l) CAN drop shield drains: only Pi A's is written; a drain landed on 0 V anywhere else ties the main negative to the lightning copper a second time, or breaks Pi B's island. One line per CAN entry: at Pi A to the stud, everywhere else cut back and taped. (m) Pi B: one surge diode across its 24 V strip at entry 1, ahead of WD-B's relay, covers both its regulators (closes item 468 (h), no added part). (n) Pi B could stay asleep for good if WD-B dies while it sleeps: software only, Pi B sets its own clock wake alarm before each shutdown (one line in Compute Bay 4.3; that the CM5 wakes on it is inferred). Parts doing nothing (Claude's pick: yes to (o) to (q)): (o) The control CAN bus's 12 V supply powers nothing: the Waveshare HAT powers its own isolated side (B0505LS-1W on its parts list, waveshare.com), the node's CAN board runs off the Nucleo, the VESC's CAN port takes no power. Drop line 1 (breaker, 16/2 run, one YRDZXG, the control power tee); keep each drop's black core as the ground reference. (p) The hub box's 12 V converter (line 12) runs only the BaroVUE and HygroVUE, a few feet from the house CAN converter; take their 12 V off the house converter through a 0.5 A fuse and drop line 12, its run, the third YRDZXG, its diode and a PG9. (q) The node's humidity breakout repeats the BME280, which reads humidity too: drop it. (r) Claude's opinion, reverses Mike's 2026-09-27 and 10-06 calls: leave the two battery bus surge modules off. They start at 48 to 70 V on a bus the bank holds near 27 V, the box diodes act first, and a module that fails shorted can blow the 300 A Class T and darken the boat. (s) The two stern 200 W panels in parallel on one 75/15 (about 14.5 A out, inside its 15 A): saves a controller, a fuse and holder, a PV surge module, a remote cable and a PV run; one controller loss then costs 400 W, as each 100/20 does. (t) The PoE light driver inside the network switch box instead of its own dry box (not bought), or the disc lights on the node's spare channel 5 if they are plain 24 V lights (not known). (u) The wing: one 22/12 hull cable spliced to the ring's fixed side instead of three cables with Deutsch plugs (not bought): two can-wall holes, two plug pairs, two wing box glands and two ferrites fewer. Fewer holes (Claude's pick: yes): (v) Split glands where cables are round, as Mike asked for the aft junction: Pi A 9 holes to about 4, Pi B 8 to 3 (no metal left in its wall, settles item 352 (c)), the network switch box 11 to 4 with no RJ45 couplers, tape wraps or patch cords (revisits the 2026-10-05 taped couplers, chosen before the split glands came), the wet lab box 14 to about 8, the BMS box 4 to 2 (and glue it to a pad instead of four bolts through the sealed battery box wall). About six more Altelix glands, about $7 each (Amazon B0GYT3ZMDL, 5-pack, $35.90). Small (Claude's pick: yes): (w) the horn's and the hub lead's inline fuses into DIN holders like the rest; (x) the Orion-Tr remote pair on a round 2-core offcut in a PG7 instead of 14/2 in a 3/4 in PG11; (y) hub box TB2's nine blocks only join wire to wire: land the wing Cat6 pairs on the readers, keep three ground blocks; (z) the UV-C LM317 and its resistor on the node's rail after channel 9's fuse (answers item 468 (hh)); (aa) node entry 4: the Ewellix feedback gets its own PG7 (two cables in one gland today). Layout questions (Claude's view: worth it, Mike's call): (bb) move the network switch box beside Pi A: it sits at the stern only because it used to be inside the aft junction, and five of its nine cables run aft only to reach it; (cc) put the CAN tees in an order that does not double back (house: wet lab tee forward of the multiport; control: node, Pis, VESC A). The C4 18/4 roll (no second roll, Mike 2026-10-31) gets lighter: (a) shortens the bilge cable and (c) takes the bow lantern off it. *Documents: Electronics plan 4.1, 5.2, 5.3, 6.4, 6.7, 7.1, 7.5, 7.6, A1, A1a, A2, A3, A4, A6, A6a, A11, A15, A17, A18; Compute Bay 4.3, 10, 11, 14; Build Guide 3.6, 4.1, 4.4; Battery Box Part 8; Instrument Post Guide 3, 8, 10; Wing Power System 1A; Wire and Cable Buy List; BOM; Box Wiring Sheets; Aft_Junction_Box_Build_Sheet_2026-10-30; Bilge Pump Wiring 2026-10-31; order tracker once answered.*

469. The SBMS0 battery monitor overheated; a new one is ordered (Mike, 2026-10-21, BMS overheating chat; ordered 2026-10-31). Mike: "Bms very hot, no display"; "It stayed hot for 20 minutes before I disconnected the ribbon cable from the winford"; "looks bricked, is there a better option for voltage monitoring?" Cause found: on the green Winford BRK2X6-L-DIN terminal board in the BMS box, every battery tap wire except black sat one terminal too low (brown on 2, red on 3, up to gray on 9), terminals 10 to 12 were empty and none of the three jumpers (1 to 2, 10 to 11, 11 to 12) was fitted, so brown on 2 put the first cell group straight across the SBMS0 (pins 1 and 2 are both pack minus). The battery end of the 12-core was right. The fix Claude gave: move every wire except black up one terminal, top first (gray 9 to 10 down to brown 2 to 3); fit the three jumpers (pins 11 and 12 carry pack plus to power the board, pin 1 pack minus, pins 2 and 10 only measure); shield wire on 2; check the 30 AWG safety links at the black and brown rings; meter each neighbor pair at about 3.3 V and 1 to 10 at about 26 V before one plug-in; thermistor (white and tan) to SBMS0 pins 15 and 16, either way round. The SBMS0 is more than a voltage reader: it is the only current measurement aboard (two shunts, battery percentage, solar harvest) and reads pack temperature (Battery Box Building Guide Part 8); a Victron SmartShunt plus the JK balancer over Bluetooth was judged worse. Decided (Mike, 2026-10-31: "new ordered (paypal)"): a new SBMS0, CA$189 (about US$135, a guess at the rate; electrodacus.com, ships from Canada). Written in the same day: Battery Box guide Part 8 (never skip a jumper or land a wire one terminal low; the meter check before the first plug-in), BOM 15.4, the order tracker (Parts and Order log). A new WiFi/USB add-on board was ordered with it (Mike, 2026-10-31: "yes ordered wifi/usb"), about CA$38. Still open: the same warning on Reference/BMS and Balancer Wiring Sheet 2026-10-03 (Part 1 work). *Documents: Battery Box Building Guide Part 8, BOM 15.2, the order tracker.* At v10.5: Still open: the warning on the BMS and Balancer Wiring Sheet.

470. Mike's rule for the rig: the deck must outlast everything above it (Mike, 2026-10-27, Titanium mast chat: "we don't care much what breaks first, as long as the deck remains"; "Just want to make sure the deck outlasts the wing"). Decided; written into the Rig Base guide at v10.4. It sits beside the 2026-10-30 rule "The goal is nothing breaks": nothing should break, and if something must, never the deck. Left: say whether Design Decisions' rig section should carry it too (Claude: yes, one line).

471. Boat 2's rig, ideas looked at, nothing chosen (Mike, 2026-10-27, Titanium mast chat). Mike: "consider the slew bearing at or near deck level (maybe 4 in up) for boat 2 ... a titanium mast design and cost"; "right now we have no way to escape a lee shore without the motor. If the motor goes and the wing is twice as big, good chance we could get around a lee shore." Claude's figures (estimates, web price ranges): bearing 4 in above the deck drops the can (about 120 lb) and grows the mast from 27.38 to about 45 in, bearing margin 1.46 against 1.95 now; Grade 5 titanium 3.500 in OD x 0.300 in wall, about 21 lb against about 70 lb in 2205, first yield about 22,250 ft-lb, weldment about $2,500 to $4,500 against $1,000 to $2,000 (titanium cannot be welded to stainless, so the mast plate and gussets go titanium too); a doubled wing (30 sq ft) needs a 4.5 in titanium mast, a Kaydon RK6-25 or RK6-22 bearing, a deck base holding about 88,000 ft-lb (about twice Boat 1's), and a new stability check, and saves about 25 to 50 days round the world. Lee shore, Claude's picks: an anchor that drops itself when the motor is dead, sea room in the route, a spare motor controller switchable from shore. The doubled-wing upwind numbers are in Reference/Wing Wind Characteristics 2026-10-27.md. Mike to say: whether to write the study up as a dated Reference sheet, and whether any lee-shore pick goes on Boat 2's list.

472. Per-terminal wiring pages for the other boxes, like the aft junction's page 3? (Mike, 2026-10-31: "A1, A2, etc.") Claude asked whether he meant every box; not answered. Mike to say: every box, or which ones.

473. Motor jacket plugs: the 4-pack ($9.99, "the third one" in Mike's Amazon search) instead of the uxcell 2-pack ($9.48, B0982SK9R9)? (Motor coolant chat, 2026-10-29.) Not answered; the guides and tracker carry the uxcell 2-pack.

474. A lightning strike tell-tale card on the wing strap near the wing root? (Claude's offer, Wing-Boom chat, 2026-10-31.) Mike asked only what "root" meant. Mike to say: yes or no.

475. The wing nose locker: two calls before the reply goes to Brandon (Wing nose locker chat, 2026-10-29). (1) Take the foam core thickness off FLR1, which assumes FLR1 was cut as the box's outside outline; (2) what LS1 is (guess: an old locker shelf, now not needed). Both need the CNC cut file "sheet 5" from Rib_Cut_Files_v8_4. No guide says how to build the locker's outside walls or how thick the core is. Claude's six-step build plan starting with FLR1 is drafted in that chat; it waits on Brandon's core-gap measurement.

476. Is the hatch moving behind the wing (22 x 22 in)? (Mike, 2026-10-27, for the 3D boat model.) Mike's model inputs: hatch behind the wing, 22 x 22 in; more solar, none in the middle; deck peaked at 7 degrees; the post 6 in from the back; no rub rail. The guides put the Lewmar size 60 hatch (20 x 20 in cut-out) ahead of the rig with six 100 W panels in the middle (Build Guide 4.4); with the hatch behind the wing only four fit, about 1,200 W on the main bank instead of 1,400 (Claude). The Build Guide's deck rises 7 in per 48 in, about 8 degrees. Mike to say: model only, or a real change.

477. The wing's bottom height above the deck (Claude, 2026-10-26, offered, no answer). The Rig Base guide puts the wing bottom about 21 in above the deck; with the 21 in can kept uncut, the stack puts it about 27 in up. Mike to say: fix the line to about 27 in (Claude: yes).

468. Whole-boat box review: the aft junction checks run on every other box (Claude, 2026-10-30, from Mike's "please review the entire build and other boxes to verify all these things"). At v10.4: (a), (b), (c), (d) and (e) are written in (the enable relay on its own 30 A module, six modules bought with four jobs; four more output fuses on the central node's rail; the puller fuses on the plus side; the two YRDZXG converters for the bow lantern and the post whites; the post wind meter's data pin). Still open: the rest, as below. Read-only review of every box against the guides (Electronics plan Appendix A, sec 7, Box Wiring Sheets, the dated drawings), looking for unfused feeds that leave the cabin, fuses bigger than their wire, gland rule breaks, glands that do not fit, missing surge diodes, signal level mismatches and docs that disagree. Each line says how sure: known from the text, inferred, or a guess. Most serious: (a) The central release enable relay is channel 5 of an 8-channel module (Compute Bay 10.3 step 2), but it carries the burn current, 12.5 A per horn on a feeder sized for 25 A, for up to 60 s; HiLetgo-class 8-channel modules use relays rated about 10 A (inferred from the usual SRD-24VDC parts; no doc states this module's rating). Release Node B uses a 30 A single-channel module for the same job. Claude's view: use one of the spare HiLetgo 30 A modules for the central enable too. DECIDED (Mike, 2026-10-31: "yes switch it"): the central release enable moves off channel 5 of the 8-channel board onto one of the spare HiLetgo 24 V 30 A single-channel modules on hand (six bought: steering cut relay, motoring whites, Release Node B, now the central enable; two left), its trigger on Nucleo pin D3 as before; channel 5 of the 8-channel board becomes a spare. Still to write: Electronics plan 4.1 and A3, Compute Bay 10.2, 10.3 step 2 and 11, Box Wiring Sheet A3, BOM 15.8, order tracker. Researched 2026-10-31 (Mike: "Please research the rating of the 8 relay board"): HiLetgo-class 24 V 8-channel boards use the Songle SRD-24VDC-SL-C (the 24 V version sold by other vendors names it; HiLetgo's own listings give 10 A 250 VAC / 30 VDC; that HiLetgo's board uses it is inferred, the blue cans normally carry the Songle name). Songle's SRD datasheet (components101 copy, read 2026-10-31), contact rating table: the changeover type (Form C, the "-C" in the part number, the kind on these boards) is 7 A at 30 V DC resistive and 3 A at 28 V DC inductive; 10 A at 30 V DC is the make-only type (Form A); electrical life 100,000 operations. The burn wire is a resistive load at 12.5 A per horn, so the central enable relay would run at about 1.8 times its DC rating for up to 60 s. The other channels are inside it: ch 1 Starlink about 3 A, ch 2 the wet lab about 4 A typical (10 A converter top, near the limit only at full load), the rest small. (b) Switched outputs at the central node with no fuse of their own, so a short trips the node's own 15 A breaker and the node (steering, the cell-temperature trip, releases) drops: ch 4 em-trak and ch 9 camera port UV-C fail ON, so a short there comes back at every breaker reset and locks the node out (known); ch 6 and ch 12 bilge manual-ons put the pump in the bilge behind the node's 15 A instead of its own 5 A (inferred); ch 2 passes up to about 10 A of wet lab converter current through a module contact (inferred). Ch 1 and ch 3 are fused at the aft junction (item 467). Claude's view: a small slow-blow fuse on every switched output on the node's rail (holders and the fuse kit on hand). Compute Bay 11 also says the fail-ON loads stay on with the node's feed lost; they cannot, since their contacts are fed from that feed (known). (c) Nav light voltage: the bow lantern and both post whites are TRUE MODS 12 to 24 V (Instrument Post Guide 3), on a bus at 27.6 V charging and up to 29.2 V (known); Electronics plan 6.4 says every fixture takes the bus voltage as it is. Only the stern light (9 to 33 V) is rated for it. I don't know whether the 12 to 24 V lights survive 29 V. (d) The cord puller fuses sit on the minus side (between the MOSFET and the reversing relay); a chafed + core onto its shield (drain at 0 V) bypasses the fuse, leaving only the 30 A breaker on 18 AWG (inferred). Moving each fuse to the + side fixes it. (e) The post wind meter's 5 V data goes straight into Nucleo D0 and D1 with no level chip; those pins take 5 V only while the Nucleo is powered, and the meter runs from the aft junction's always-on feed, so with the node off it drives 5 V into an unpowered pin (guess from ST's pin ratings). Surge diodes: (f) the central node has one TVS (at its 5 V converter); Lightning Guide 7.7 says every power input (entries 2a, 12, 29 have none) (inferred); (g) Release Node B has none in A15 or Sheet A15, on a 10 to 12 ft feed (inferred); (h) WD-B's D36V6F5 has none drawn though Lightning Guide 7.7 lists it (inferred); (i) the switch box has none and A6a says nothing lightning related is inside, against Compute Bay 14.1's every-converter rule; write the exemption or fit one (known); (j) the wet lab box diode is across the XWST output in A18 and Sheet A18 but at the input in Wet Lab Box Layout 2026-10-15 (known); (k) science data lines: Lightning Guide 7.5 keeps their surge protectors, A18 runs the DO and SBE 45 lines with none (known); (l) Lightning Guide 7.6 still says the BMS and VESC feeds are surge-clamped downstream; neither is now (known). Glands: (m) Iridium A's 16/2 feed in a PG7 (A11, Sheet A11-A); every other 16/2 gets a sealant-filled PG9 (known). (n) Central node entry 16 and aft junction entry 10 put three 16/2 runs in one PG13.5; 7.2 allows two, and three oval jackets are about 0.6 in across against about 0.47 in a PG13.5 seals (guess on the sizes). (o) The BMS box entry 3 puts two loose Cat6 pairs in one PG9 (keep them in one Cat6 jacket, or a gland each) (known). (p) The three slip ring hull cables, of different sizes, share one deck gland, which has no size or buy line (known). (q) Duplex entries not marked sealant-filled: central node 2, 2a, 12, 29, 30, Release Node B 2, Starlink enclosure power (known). (r) The split gland is "PG25" in 7.1, A1, A1a and A2, but "M30, 1-3/16 in hole" in the hub box drawing and item 447 (known conflict). (s) The VESC A box's two Micro-C cords in PG7 may be over 1/4 in (guess). (t) Wing box: five PG9s barely fit the 5.9 in wall, and the shielded Cat6 may need a PG11 (guess). (u) The wet lab drawing's staggered rows sit about 0.9 in apart against about 1.0 in needed (inferred). Fit: (v) The switch box's Mean Well DDR-120B-48 is about 4.9 in tall (seller spec) in a 3.9 in deep box: the rail must run up the wall, which no doc says; the jacks then land on the two end walls, which no drawing shows (supply height known, crowding a guess). (w) The BMS box size is never given, so its four entries cannot be checked (known). Wire against fuse: (x) the 300 A Class T and the 250 A MEGA each guard 2 AWG (about 210 A at 105 C); the boat wiring rule (ABYC E-11) allows up to 150 percent on these, so it passes there, but 7.6 says never past the wire rating (Claude's note: reword 7.6). (y) The wing tip's 1 A fuse is at the tip, so the 22 AWG pair up the mast is guarded only by the wing box's 5 A (inferred). (z) Six stud-to-breaker jumpers on the bus board drawing look over 7 in with no split loom shown (breakers 15, 14, 13, 2, 4, 1) (inferred from the drawing grid). (aa) The hub's 5 V lead has no wire size, so its 3 A fuse cannot be checked (known). Docs that disagree or are stale (known): (bb) shield rule 7.4 ("everywhere else it floats") against A3 entries 4 and 4a (18/4 drains to 0 V), the detector lead's drain at Pi B, and the HygroVUE shield landed in the hub box; (cc) vent: 7.4 says the central node only, A9, the Battery Box guide and the totals keep the battery box Gore vent; (dd) the bus board drawing still shows line 13 as 16/2 (14/2 since 2026-10-15) and two MEGA holders against 7.6's four; (ee) the relay modules' trigger jumper setting is written nowhere, though A18 says to set it as the central node's; (ff) PC817 for the island-alive line drawn in both Pi A and Pi B; (gg) the CAN drops' 12 V pair has no stated landing at either Pi HAT, and at Pi B a wrong landing ties the floating island to the main negative (inferred); (hh) no home for the UV-C LM317 and its resistor, and the UV-C cable now enters the camera tube through a port of the cap's split gland (item 513 (q)); (ii) the wing box is A17 in the plan but lives on Sheet A14; (jj) Wet Lab Box Layout 2026-10-15 and Reference/Wet Lab Box 2026-10-14 still show a vent; (kk) Reference/Wing Electronics Wiring Sheet 2026-09-24 describes the deleted wing tub but the Instrument Post Guide still cites it; (ll) Iridium to Pi Wiring 2026-10-15 still says one USB isolator to buy (both bought 2026-10-16); (mm) Reference/Battery Tap Wiring 2026-10-03 still says "tap bundle"; (nn) the horn's 5 A fuse is missing from 7.6's still-fused list. DECIDED (Mike, 2026-10-30: "Yes") on (b) and (d): four more 5 x 20 mm slow-blow fuses in DIN holders on the central node's rail, each right after its relay contact: ch 4 em-trak 2 A, ch 9 camera port UV-C 0.5 A, ch 6 and ch 12 bilge pump manual-ons 5 A each; and the four cord puller fuses move to the + side (release bus to the reversing relay input), same sizes. Still to write: Electronics plan 4.1, A3 and 7.6's still-fused list, Compute Bay 10.3 and 11, Transom Drogue Box Guide 6, Box Wiring Sheet A3, BOM 15.7 and 15.8, and the order tracker (DIN fuse holders now about 18 boat wide: central node 8, aft junction 5, wet lab box 5; count the MECCANIXITY pack). Claude's recommendations on (b), (c) and (e), asked 2026-10-30 (Mike: "what do you recommend for fuses? need to be sensible", "do we need voltage reg to 12v for the lights?", "#5 please research"): (b) four more 5 x 20 mm slow-blow fuses in DIN holders on the central node's rail, each right after its relay contact: ch 4 em-trak 2 A (the B921 averages 135 mA and peaks 2 A at 12 V, published; about half that at 24 V, inferred), ch 9 UV-C 0.5 A (the smallest in the kit; the LEDs draw about 20 mA), ch 6 and ch 12 bilge pump manual-ons 5 A each (the same as each pump's own breaker). None on ch 2 (its own 15 A breaker upstream), ch 7, 10 and 11 (inside the cabin, a few milliamps). The four puller fuses move to the + side, same sizes. Fuses from the QBGTFAK kit on hand; holders: count the MECCANIXITY pack (central node 8, aft junction 5, wet lab box 5). (c) No 12 V converter: a converter is one more part that can fail dark, and the guides keep the light circuit converter-free so fail-on means what it says. TRUE MODS publishes no upper limit for its 12 to 24 V lights (I don't know whether they take 29 V); its stern light is sold as 9 to 33 V, so the brand states a wide range when it has one (inferred: the 12 to 24 V ones may really stop near 24 V). Cheap guard with parts on hand: six 1N5408 diodes in series ahead of the bow lantern (after F4) and six ahead of the whites (after F3), on DIN blocks in the aft junction; about 0.7 V each at these small currents, so about 25 V at the light at full charge and about 20 V with the bank low, both inside 12 to 24 V. A diode usually fails shorted, which leaves the light lit. The stern light needs none. Mike, 2026-10-30: diodes are easy to fit the wrong way round (12 of them, each one-way) and he would rather have a 12 V converter. Claude's revised pick: the two spare YRDZXG 24 to 12 V converters on hand (bought with no job, BOM 15.4), one after F4 for the bow lantern and one after F3 for the two whites; the stern light stays on the bus. Cost: a dead converter darkens its light (the diodes would have failed lit). Input range: the Amazon listing's text gives 12 to 32 V (shared text across its sizes, so inferred for this one). DECIDED (Mike, 2026-10-30: "yes"): the two spare YRDZXG converters go in the aft junction box, drawn into the build sheet the same day (bow converter red in from F4, whites converter red in from relay NO, outputs joined to the light wires in lever connectors). Still to write: Electronics plan 6.4 ("no converter anywhere in the light circuit") and A6, Instrument Post Guide 3, BOM 15.4 (two YRDZXG off the no-job list), order tracker. (e) Researched: the Calypso ULP manual (UART/I2C version) gives power 3.3 to 18 V and does not state the data level (marine-products-direct.com copy of Calypso's ULP STD UART/I2C manual, read 2026-10-30); a user report says 5 V TTL (secondhand). ST's own staff give the rule for an unpowered STM32 five-volt-tolerant pin as at most min(VDD + 3.6 V, 5.5 V), which is 3.6 V with the chip off (ST community answer for another STM32; the G431 datasheet's table could not be fetched, so the exact figure is inferred). So 5 V into D0 with the node off is over the limit, if the meter's data is 5 V. Fix that works whatever the meter's level: power the meter from the central node's own 5 V, down two spare trunk cores through a 0.5 A fuse at the node, so the meter and the Nucleo are always on or off together; the aft junction then loses its 5 V regulator and fuse F1 (a change to Sheet A6 and the build sheet, so Mike's yes first). The meter draws 0.25 mA, so the 30 ft or so of 22 AWG costs nothing. A divider on the data line would only work if the meter's level were known. Evaluated further 2026-10-30 from ST's datasheet DS12589 (Rev 2, Table 14 and the pin table): D0 is PA10 and D1 is PA9, both five-volt tolerant pins (FT_da, FT_fd). Their limit is the chip's own supply plus 4.0 V: about 7.3 V with the Nucleo on (5 V is fine), only 4.0 V with it off. These pins have no path into the chip's supply ("positive injection is not possible", Table 15 note 3), so 5 V with the chip off does not power it up; it stresses the input itself, 1 V past the rating. Likely result: usually nothing, at worst that one input fails and the post wind reading is lost (the wing-tip meter is the backup); nothing else on the boat is at risk (inferred). It happens only while the node is off and the aft box is on, and only if the meter's data really is 5 V (unknown; the meter runs on 3.3 to 18 V, so its own logic may well be 3.3 V, inferred). A series resistor would not help (the pin draws almost no current, so the full 5 V still reaches it). Claude's view: small risk, small stakes; powering the meter from the node still removes it for free (two spare wires, one less part), but leaving it as drawn is also reasonable. Mike's call. Researched further 2026-10-30 (Mike: "prefer to avoid adding complexity for these kinds of hypotheticals"): six versions of Calypso's own ULP manuals (calypsoinstruments.com) give the supply as 3.3 to 18 V and the current "at 5 V", call the output "UART/TTL", and say the input wires carry TVS diodes, but none states the data level; no forum or code example found measures it (one ArduPilot post says "5V TTL", from the manual, not a measurement). So the level stays unknown. The only no-added-part change would be swapping the 5 V Pololu for its 3.3 V twin on hand (D36V6F3, same board), but that runs the meter at the very bottom of its 3.3 V rating. DECIDED (Mike, 2026-10-30: "agreed"): leave it as drawn; the meter keeps its own 5 V Pololu in the aft junction box; point closed. Claude's recommendation was: leave it as drawn and close this point; the exposure is brief (only while the node's breaker is tripped and resetting), and the worst case is losing the post wind input, with the wing-tip meter as backup. Checked and fine: the other branch breakers against their wire, the stud pairings, the backup board's fuses and ANL, Pi A and Pi B wall fits, the battery box and BMS cable sizes and core counts, the stern release cables across all five documents, the central node's wall fit. *Documents: as named in each line.*

463. Boom-root pocket, boom, tail and trim drive: what is left after v10.4 (Claude, 2026-10-31). The decided design (the pocket under one lid on the wing's centerline, the actuator on the spar's back face, the DTM 4-pin plug, the G10 flat tab with its 2 in gap and 10-32 screw, the 1/4 in 316 pushrod in a 3/8 PEX liner, the boom and its four 5/16 in root bolts, the one-piece tail two thirds above the boom on four 2 in hinge pieces, the give-way spring and 2 in horn at the flap, the bias spring, no spring link and no breakaway, the soft limits, the wing's lightning wiring, the two 1/2 in PEX runs, the 3/4 in mast plate hole and the butt splices at the slip ring) is written into the v10.4 Trim Guide, Wing Construction Guide, Wing Power System, Lightning Guide, Build Guide sec 6, Design Decisions, BOM and Glossary. The full record of 2026-10-27 to 10-31 is in Archive/Pending_Amendments_v10_4.md. Left: At v10.5: (a), (b) and the surge clamp call are in the guides. *Questions for Mike:* (a) glue or no glue on the flap axle (Reference/Tail One Piece 2026-10-30 page 3 says glue it into both end plates; the 2026-10-31 build sheet does not); *settled 2026-11-02: no glue; the axle sits in a blind 3/16 in hole in each end plate and is trapped once the plates are glued in (Mike distrusts glue on stainless); tail sheet pages 2 and 3 now say so*; *2026-11-02 (Mike: "We can't read 7 pages at once"): the seven wing drawings are now three PDFs, about half the words, built by Reference/_make_Wing_Drawings_2026-11-02.py: Wing Boom Pocket Build 2026-10-30 (boom, pocket, then the actuator tab), Reference/Tail One Piece 2026-10-30 (tail, flap spring templates and steps) and Reference/Wing Lightning Wiring 2026-10-30 (wires, then the surge clamps). Mismatches fixed on the way: the root PEX's pocket end (open, not silicone-filled), the ground wire's skin hole (1/4 in), the face run's height (44-1/2 in, as drawn), the rear pin (26 mm or more between grooves), the tab's second fastener (the 10-32 screw, not a 1/8 in pin), the ground wire (solid 8 AWG, Home Depot, #10 lugs to buy)*; (b) the give-way spring sits at about 58 percent of its rated twist, past the guide's half rule: accept, or a stronger spring; *settled 2026-11-02 (Mike: "yes, keep the spring"): keep 9287K47; Wing Trim guide v10.4a updated*; (c) the tail slot clearance fix (liners glued with the taped boom as the mold); (d) his read of the surge clamp sheet's details (Reference/Actuator Surge Clamps 2026-10-31); (e) and (f) settled 2026-10-31: the pocket build has its own section after Stages 8 and 9 of the Wing Construction Guide (Mike: "yes"), and the Trim Guide keeps its name (Mike: "don't care, whatever you prefer"; Claude's pick, since "trim" still names its job and a new name would change every pointer for nothing); (g) review ideas never answered: a 3/16 in pushrod (saves about 1.2 lb with its lead), a lightning wire up the tail's front edge, a surge diode across the tip's 24 V pair. *Waiting on facts or parts:* (h) whether the MD's 24 V negative is tied to its case (Thomson's manual, or the meter at delivery, due Nov 2); if tied, the jumper becomes a 1.5KE33CA tie; (i) the rear pin's length in the McMaster cart (26 mm or more between grooves), the fork's slot depth, the clevis jaw length, the motor cable boot, the overload trip force, the lead length (0.3 or 1 m); (j) parts to pick: jam nut, 10-32 screw, rubber boot, the root bolts' seller, 8 AWG ring lugs for #10 studs (the ones on hand are 3/8 in); McMaster and Amazon prices unchecked; (k) the nose lead total against the 24 lb rack (Stage 10); (l) Thomson's part and price to log; the mast plate cutting sheet PDF still shows the center hole (tell the shop); (m) the 18/4 actuator cable is 0.26 in in Wing Power System and the Spec Sheet, 0.25 in in the Trim and Construction guides: one figure. *Decided 2026-10-31 (Mike: "ok to use 1.5KE33CA for all 4?", then "not room for Taidacent, will use diode"):* the two CAN wires keep the 1.5KE12CA (the 33CA lets about 46 V through, a gamble for the actuator's CAN chip); the power pair keeps the 1.5KE33CA; the 1.5KE parts' capacitance is acceptable on the 250 kbit/s link (about 0.15 microseconds per edge against a 4 microsecond bit, worked out, rough). *Drawing cleanups (Part 1 work):* Wing Boom Pocket Build 2026-10-30 page 3 step 3 still says fill the root PEX's pocket mouth with silicone (it stays open, 2026-10-31); Reference/Wing Lightning Wiring 2026-10-30 gives a 3/16 in ground wire hole (1/4 in), holes 3/8 in apart (1/2 in), 44-1/2 in up (44-3/4), 24 mm between the rear pin's grooves (26), an 11/16 in PEX hole (3/4 in), and "the 12 AWG core is about 0.15 in" (bare 8 AWG, 0.128 in); the second review's notes 19, 20 and 24 are on no sheet; Reference/Boom Tail Actuator Review 2026-10-30.md "Decided after the review" B and F and the 0.56 in soft limits are stale; Reference/Boom Root Strength Calc 2026-10-28.md is not redone for no breakaway and 1/4 in plates. *Software (software repo):* the soft limits, restart time, status alarm, damper deadband, heel hold and the CAN terminators.

440. Questions from the v10.3 accuracy check (Claude, 2026-10-19). Each has an Open line in the guides named. (a) The cellular units' control output: Build Guide 8.3 and Design Decisions R-8.3 give the Primelinks one output that power-cycles the active Pi, but Compute Bay 4.3 says the watchdogs have no remote trigger, on purpose, and no hole list carries the wire. Keep it (then Compute Bay and the Electronics plan get the wire) or drop it (Claude's view: drop it; the watchdog already restarts a hung computer). (b) The rudder stock bellows boot: the one bought went back (refunded 2026-10-02). Buy another, and which, or go without? (Build Guide 3.8, Steering Handbook, BOM 15.10.) (c) Science on the load-shed ladder: the Settings Sheet says science runs full to the 10 percent floor in the tropics, and also that it is off from 30 to 50 percent. Does the tropics exception stand? (Settings Sheet sec 4, Routing Guide 2.3.) (d) Boat 2 at Cape Horn: Routing Guide 7.3 says stay 50-plus nm south of the cape, but 7.1 aims the drogue at about 56.05 to 56.4 S, only about 4 to 25 nm south. Which holds? (e) The post lights' cable: Instrument Post Guide 10.1 runs them on one four-core cable, which is on no buy list; buy a four-core, or run two 16/2 cables through a second gland? (Wire List B2, Electronics plan A6.) (f) Surge parts on the post's wind and light runs: Instrument Post Guide 10.3 calls for surge diodes at the junction and the central node, no other guide has them, and the 33 V diode on hand does nothing on a 5 V line. Fit them (a 5 V part for the wind line) or drop the line? (g) The shaft thrust block's bond wire (Lightning Guide 6.2 item 2): its ball bearing conducts, so the wire ties the shaft to the copper, the very path the spark gap is there to stop. Drop the wire (Claude's view) or keep it? (h) The sound archive: plain 48 kHz recording fills the 4 TB drive in about 16 months, not 18 (Compute Bay 4.1); record as FLAC, or accept about 16 months between refits? (i) Two dated sheets at the top of the folder, Box Parts With Photos 2026-10-15 and USB_Hub_Box_Wiring_2026-10-14, show dropped parts (the Iridium isolators, the returned TICONN Iridium boxes, the hub on a DIN rail). Move both to Archive? (j) Moot: the coolant loop is dropped and the motor's ports plugged, so no M16 barbs are used (item 466, 2026-10-29). *Documents: as named.*

427. Box parts check, every box: what is missing (Claude, 2026-10-14, from Mike's "review ALL boxes and see what parts are missing"). The full list, box by box: Reference/Box Parts Missing 2026-10-14 (.md and .docx). Three causes of the waits: small parts no guide ever counted, parts that shipped with no delivery mail, and parts that wait on a choice. (a) To buy now, nothing to decide (added to the tracker Buy list 2026-10-14): the wing box (the TICONN 5.9 x 5.9 x 3.5 in picked 2026-10-12 was never ordered); a second and third 100 ft roll of 16/2 (need about 220 to 260 ft against 100); an SMA bulkhead-to-male lead 2-pack for the two GPS boards (one inside lead on record, two needed); 30 AWG tinned copper wire for the 22 fuse links (Wire List E4 says make them from 30 AWG wire, none was ever bought); 3/8 in ring lugs for the VESC's 8 AWG and 12 AWG leads; neutral-cure silicone for the VESC capacitors (item 417); M4 316 pan-head screws for the cord puller motors (item 276); plus the rows already on the Buy list. (b) Count, then buy only the shortfall: sealed inline fuse holders (about 13 needed, 9 on hand; item 401 p, less the hub box fuse dropped in item 426), membrane vents (about 15, 9), crimp butt splices 22 to 18 AWG (17, type on hand unknown), WAGO 221-415 (8: 2 at the VESC, 6 in the battery box), Micro-C 2 m cords (about 11, 8 on record), DIN fuse holders (8), glands by size (PG16 x7 first). (c) Mike's calls that block buying: the USB hub box, wing tip box, light driver box and second drogue box (pick each); the wet lab's reader and switch board (none picked); the slip ring's Deutsch DT plugs (pin plan not written); the release trunks' third gland (DECIDED 2026-10-26: yes, a third gland at each end, item 456); whether Pi A keeps the INA226 (Claude: strike it); Pi B's metal SMA bulkhead; the 5 V TVS on the detector lead (not picked); the emergency bank strip's fuse sizes; the VESC's kill, temperature and switch plug types. *Documents: order tracker Buy list; the guides named in the Reference file as each choice is made.*

410. SBMS0 stream: swap the micro USB lead for a serial adapter on the add-on board's green push-in block? (asked by Mike, 2026-10-13). The WiFi/USB add-on board has a six-pin green push-in block (GND, 3.3Vdc, TX, RX, SCL, SDA: the same serial stream as the micro USB socket, on the isolated side; manual page 15). Bare wires pushed into it hold better than a micro USB plug, whose small socket and solder tabs are the weakest plug in the watchman box. The block is plain 3.3 V serial, not USB, so reaching the hub takes a USB-to-serial adapter: the DSD TECH SH-U09C (Amazon B07BBPX8B8, $12.49, FTDI FT232RL, jumper set to 3.3 V so its VCC pin gives 3.3 V; checked 2026-10-13) in the watchman box, four wires to the block (GND to GND, VCC to 3.3Vdc, the adapter's TXD to the block's RX and RXD to TX, crossed), its USB-A plug into a USB-A extension lead to the hub, the joint tied down and staked. Not the SH-U09G cable or an FTDI TTL-232R-3V3-WE: both give 5 V on their power wire, which must not go to the 3.3Vdc pin. Pi A's own serial pins are taken by watchdog WD-A, so the adapter route is the only one. Claude's opinion: a modest but real gain for $12.49, do it. If yes: Battery Box Guide Part 8 and 10, Electronics plan A4 entry 4 and A1a, Settings Sheet sec 1, BOM 15.4, Box Wiring Sheets A4, order tracker Buy list. If no: nothing changes; the micro USB lead stays, tied down outside the plug.

405. Where to run the offshore trial: Brunswick, a spot nearer the sound, or the Gulf? (asked by Mike, 2026-10-08). Brunswick's hard parts: an 18 nm harbor run through the ship channel from Brunswick Landing Marina; a trial area 34 to 46 nm past Buoy STS, put there to stay outside right whale critical habitat in calving season (November 15 to April 15); winter fronts; the Gulf Stream beyond. Options: (a) launch from a marina nearer St. Simons Sound (Jekyll Harbor Marina or the marinas at the St. Simons causeway), which roughly halves the harbor run (guess: about 10 nm to Buoy STS; Jekyll Creek is a known shoaling spot on the waterway, fine at mid-tide for 3.5 ft draft, inferred); (b) pull the trial box in to about 15 to 20 nm offshore, inside the critical habitat, which is not closed to a 2 to 3 kt boat (inferred: the speed and approach rules bind larger or faster vessels and approaches to whales), halving the chase boat run; (c) run the trial on the Gulf coast (Pensacola, Panama City) before trucking to Brunswick: closer to Tulsa, no Gulf Stream, no right whales, deep water close off Destin, but a second haul, truck and launch, and less time before a December 26 departure. Claude's opinion: (a) plus (b) at Brunswick; the Gulf only if the Brunswick trial slips. Mike's call. *Documents: Boat 1 Route sec 4; Build Guide sec 11.3; the Coast Guard answers (d).*

406. Leave from Galveston instead of Brunswick for Leg 1A? (asked by Mike, 2026-10-08). Worked in Reference/Galveston Start Leg1A 2026-10-08.md. The track: Galveston ESE across the Gulf to south of the Dry Tortugas (about 680 nm), then east and north through the Florida Straits riding the Florida Current to off Cape Canaveral (about 410 nm), then east north of the Bahamas to join the Brunswick track 50 nm south of Bermuda; the rest is the same. About 1,050 nm longer (4,680 nm) and about 3 weeks longer: 80 / 93 / 113 days against 64 / 72 / 85, counting a wait in the eastern Gulf for a gap between fronts (inferred). Leaving December 26 reaches the Canaries about March 29 instead of March 8; leaving about December 5 keeps the March 8 arrival. Against: about 4 days in the Florida Current instead of a 1-day Stream crossing, in the choke point the Routing Guide avoids (sec 1.2) and Boat 1 Route sec 3 rejects for a winter start (a norther in the Stream with no room to turn back); more Stream lightning; 1,311 oil and gas structures still standing in the Gulf (BSEE file of 2026-10-08), 38 within 10 nm of the straight track, all in its first 270 nm; Galveston's tanker traffic; between fronts the southern Gulf's NE to E wind sits forward of the beam (inferred); the Coast Guard answers would go to Sector Houston-Galveston instead of Savannah; Cuba on the south side of the Straits (sanctions rules not researched). For: about 550 road miles from Tulsa against about 1,100; the offshore trial and departure in one place with no right whale rules (item 405 option c without the second haul and truck); two weeks in the Gulf with Tampa and Key West close, a shakedown before the Atlantic. Leg 1B still lands at Brunswick: home to Galveston means the Straits against a 2 to 4 kt current, or the Caribbean in October and November, where the late storms form. Mike, 2026-10-08: the Gulf leg is 3 more weeks of trial before leaving US shores, in case surprise repairs come up. Claude agrees it changes the answer: from Brunswick the boat is near home about a day and a half before the Stream, then cannot come back; from Galveston it spends about 2 weeks never more than about 240 nm from a US port, meets a Gulf norther within reach of help, and Key West is a last stop before the Straits (the Reference file, sec 4). Claude's opinion now: Galveston, keeping December 26 and landing in late March (refit about 5 months; the September return does not move). Mike also asked about Port Arthur or Cameron, LA: not easier (sec 5). About 50 road miles and a day at sea shorter, but 2 to 3 times the platforms along the track, a 20 to 30 mile channel shared with LNG carriers under moving security zones, and few yards for a masted sailboat; Galveston is the best of the three (opinion). Whatever the port, the Spain research filing should give an arrival window through late April 2027. Mike's call: switch the start to Galveston? *Documents: Boat 1 Route secs 2, 3, 4; Routing Guide sec 1.2.*

390. Coast Guard answers for Savannah (the COTP risk-assessment topics a to l): suggested wording for the yellow gaps, written 2026-10-08. Mike's draft of 2026-10-07 had yellow gaps. Claude's suggested wording is in green in Reference/COTP Savannah Answers Suggested 2026-10-08.docx (US letter); yellow is left only where the facts are Mike's: his FAA pilot certificate and ratings; the shore watch keepers (names, how many, experience); how often the Primelink units report position. Also Mike's to do: make watch@viatrax.com (or give the real address); book the escort and the offshore chase boat (Sea Tow Brunswick, which Sea Tow's 2021 article says is run by Brunswick bar pilots, phone 800-473-2869; or TowBoatUS Brunswick, Saltwater Cure LLC on Jekyll Island, (877) 283-1564; a BoatUS membership is $165 a year, and each TowBoatUS port must cover at least 25 miles from home, so the trial area 33 to 42 nm out is likely a paid job); get an FCC Restricted Radiotelephone Operator Permit (Form 605 in the FCC's online licensing system, $35, no test, a pilot certificate qualifies, issued in days); take a Rules of the Road course (National Seafarers Academy "Nautical Rules of the Road," 20 hours, Coast Guard approved, price not found). Where to get insurance quotes (2026-10-08): the Shipowners' Club in London has a liability policy written for autonomous and remotely run vessels (collision, wreck removal, towage, pollution; it covered about 80 small uncrewed craft under 79 ft (24 m) as of ABB's report), contact through https://www.shipownersclub.com/our-services/cover-provided/autonomous/; Viatrax's own business insurance agent, who can place marine cover; a US ocean marine market such as Travelers Ocean Marine, through a broker, with custom wording. No US broker was found advertising a program for uncrewed boats, and ordinary yacht policies assume crew aboard. Liability is the must-have; hull cover is harder to find. Suggested, for Mike to confirm: $1,000,000 liability insurance including wreck removal (Claude's opinion; Spain's floor is about $390,000, items 261 and 139); the watch procedure ready by November 15, 2026. One fix found while filling it: the draft said an all-round white shows sunset to sunrise. The design shows the bow bi-color and the sternlight at night, and the two post whites only while the motor runs (Compute Bay Plan sec 11, channels 3 and 7); the suggested copy says so. New questions it raised: items 391 to 395. Watch procedure (2026-10-08): Claude's draft is Reference/Watch Procedure PRIME RANGER 2026-10-08.docx (markdown beside it; US letter, 4 pages): who stands watch, what to check each shift, red and amber alerts and what to do, the quiet-boat time limits (2 hours near shore and in the trial, 12 hours at sea), who to call, notices, commands and who may send them, the log and drills. Still to fill: the watch keepers and rota, the Primelink report interval, Portugal's rescue center number; confirm the Sector Charleston Command Center number (833-453-1261 on the Coast Guard site; 843-740-7050 on an older page). Chase boat for the offshore trial (2026-10-08): the trial area is 34 to 46 nm from Buoy STS (computed, about 40 nm to its middle), 52 to 64 nm by water from Brunswick Landing Marina; at 15 to 20 kt that is 3 to 4 hours out, and a tow back at 5 kt about 12 hours. Needed: on call (not on station) for the about 5 trial days plus the harbor days; a boat fit for 60 nm offshore in winter; a licensed captain with an assistance towing endorsement for towing for hire; towline and bridle, VHF and AIS. The Coast Guard answers' "about 3 hours away" should read "about 3 to 4 hours away". Rules of the Road course (2026-10-08): NATSEA's is "blended" (part online; how the rest is done and the price are not posted); fully online choices: Maritime Institute, 16 hours, $400, final exam taken in person with a proctor; ASOS captains' course, self-paced online, $395, a completion certificate (Coast Guard approval not stated). Mike to pick; the Coast Guard answers name NATSEA until then. Mike's shorter version of 2026-10-08 (Reference/COTP Savannah Answers MINIMUM 2026-10-08.docx) is now the working copy: it drops the offshore trial and the escort. Claude's notes on it: fill the hull color (white); drop "or take remote control" and "or cellular command" (no steering command is on the boat's command list, and the cellular units only listen); "computer or power failure" should be "computer failure" (a dead battery takes the lights with it); the cone row should say no cone carried (item 392); the horn row stands (item 391); the unescorted 6 to 9 hour channel run is the line most likely to draw questions. Trial site (asked by Mike 2026-10-08, answered in chat): easier spots near Brunswick (a marina nearer the sound, a trial box nearer shore) and the Gulf coast; see item 405. *Documents: none in the set; the Reference file above.* Note 2026-11-01: shore rerouting and remote control are now to be added to the boat (item 496 (g)), so "take remote control" can go back into the answers once that is decided.

393. No tow point on the boat (found 2026-10-08). Tows are planned in and out at Las Palmas and off St. Simons Sound at the end (Boat 1 Route secs 4 to 6), and the Coast Guard answers count on an escort that can tow. No guide names a bow tow eye or how a towline is made fast; the cleats and pulpit were stripped (Build Guide sec 2). Needed: a bow tow point a towboat crew can reach from their own deck with nobody aboard, for example a bow eye through the stem, low, with a backing plate, and a short pendant led up to the deck. Mike's call on the kind. *Documents: Build Guide; Boat 1 Route.*

394. Brunswick harbor: tow the boat between the marina and Buoy STS instead of running it under escort? (Claude's opinion, 2026-10-08). The run is about 18 nm: 6 to 9 hours at 2 to 3 kt, against about 10 hours of late-December daylight at Brunswick (inferred). The ebb at the sound's mouth is strong (Waterway Guide; speed not found). Under tow at 4 to 5 kt, the speed the lake tow test already uses (Build Guide sec 11.2), it takes about 4 hours, the towboat carries the lookout and sound signals, and the Coast Guard answers on lookout, take-over and fog near shore get simpler. The boat would run on its own only seaward of Buoy STS. Cost (2026-10-08): towing companies bill non-members about $250 to $300 an hour or more, more at night or in bad weather (BoatUS; GEICO, Sept 2026, says $300 and up), timed from leaving their dock to getting back. Claude's estimates from that rate: one marina-to-Buoy STS tow about 5-1/2 hours, about $1,400 to $1,700; the three harbor tows (trial out, trial back, departure) about $4,000 to $5,000; a recovery from the trial area, if needed (corrected 2026-10-08: about 58 nm by water from the marina, about 4 hours out and 12 hours back under tow), about 16 hours, $4,000 to $5,000; the November 2027 tow in from off St. Simons Sound about $1,500 to $2,500. A $165 BoatUS membership is for breakdowns; a planned move is very likely billed at the hourly rate (inferred). A chase boat kept on station for the 5-day trial would cost far more than one on call; day rate not found. Needs the tow point (item 393). Mike, 2026-10-08: no need to decide today; do not ask again until he raises it or the escort is being booked. *Documents: Boat 1 Route sec 4; Build Guide sec 11.3.*

395. What the boat does when every link goes quiet, and how the Starlink link is secured: neither is written down (found 2026-10-08). The Coast Guard answers needed both. Suggested there: with no comms the boat keeps to its plan (inside the box during the trial, on its route at sea), lights and AIS as normal; shore calls the Coast Guard after 2 hours silent near shore and in the trial, 12 hours at sea (3 missed reports at the 4-hour rate). Link: commands over Starlink carry the same HMAC signature as Iridium ones; Starlink traffic inside an encrypted tunnel (WireGuard) with no open ports; shore server logins per person with two-factor sign-in. To confirm with the software side and write into the software repo; the guides need only the comms-loss line. *Documents: Build Guide secs 8.3 and 9.1; software repo.*

382. Pi B's converter while Pi B sleeps (found 2026-10-07; Mike's call). v10.2 writes in the watchdog design Mike ordered the relays for (item 375): each Pi's 24 V feed runs through the normally closed contact of its watchdog's relay, ahead of the Pi's converter, and each watchdog runs on its own Pololu D36V6F5. With the coil off nearly all the time, Pi B's potted Klnuoxj stays powered while Pi B sleeps (Pi B only shuts itself down), and its idle draw is not published: converters of this kind typically idle at 10 to 30 mA at 24 V, about 6 to 17 Wh a day (inferred) of the backup island's 25 to 32 Wh budget. The question: should WD-B hold its coil on while Pi B sleeps, so the converter is fully off (about 0.4 W of coil instead, a guess at a 5 V relay coil: roughly 10 Wh a day), or accept the converter's idle draw? Claude's opinion: accept it; holding the coil costs about as much as it saves and turns the fail-safe relay into one that must stay energized. No bench test (Mike, 2026-10-07). *Documents: Compute Bay 4.2, 4.3, 5.3.*

373. Starlink Mini on deck: what covers and holds it, and how its Ethernet comes out (asked by Mike, 2026-10-05). Cover answered 2026-11-02: no box (item 504). Still open: what holds it down. Mike is worried the bare Mini is not tough enough for the open sea. The docs say only "a sealed enclosure" (Build Guide comms section; Electronics plan A13) and name no part. Facts (Starlink spec): the Mini is IP67 with its cable plugged in, works in wind of 60 mph and more, -22 to 122 F. Below deck is out: the deck is 3/4 in glassed okoume, and wet wood soaks up its signal (Claude, inferred). Claude's recommendation: the Seaview APEX low-profile mount, marine aluminum, powder coated, 2 in tall, the cable through a sealed pass-through (Amazon B0GGD3L6SY, https://www.amazon.com/SEAVIEW-Starlink-Heavy-Duty-Compact-Marine/dp/B0GGD3L6SY), with its HDPE protective cover (APXMRMPC; Seaview says no measurable loss with it on; not yet found on Amazon). Bolt it through the deck with backing, low, where green water hits it least; check signal in the Starlink app with and without the cover before sailing. Price not checked. Ethernet (Mike, 2026-10-05, confirmed on the Starlink spec sheet): the Mini has one latching Ethernet port made for Starlink's own plug (Starlink spec sheet). A standard RJ45 plug fits, but the Mini is then no longer rated IP67, so seal that plug the same way as the box jacks: dielectric grease, then self-fusing silicone tape (item 370). The docs' "Starlink coax" is really its Ethernet cable and its DC power cable (12 to 48 V on a DC5521 barrel plug); the Mini has no coax. Mike, 2026-10-05: the Seaview mount and cover take too much room; wants something smaller, and thinks green water would be too hard on the Mini. Claude's idea: mount the Mini flat on a short G10 arm off the instrument post's starboard face, about 40 to 44 in up, below the wind sensor (head at 51-1/2 in) so it does not foul the sensor's clean air, and inside the air terminal's protected zone. Up there green water rarely reaches it; flat, it shows only its 1-1/2 in edge to wind and spray. The G10 arm is the part meant to break first in a rollover, per the post's weakest-first rule. Check against the post's starboard face layout (the radar reflector and the cable exit are there) and whether the post's top 6 in blocks any of its view. Mounting part not picked. Mike, 2026-10-05: no good room on the post; the Mini should lie flat on or under the deck. Under the deck: the wood is sealed in epoxy and glass, so it stays dry. Claude's estimate (inferred, not measured): sealed, dry 3/4 in okoume with its glass and paint costs the signal roughly 1 to 3 dB; a film of salt water on top costs more, but it does that to a bare dish too. Test before deciding (next step): glass and paint a scrap of the deck plywood the same way as the deck, lay it over the Mini outdoors, and compare the Starlink app's speed test and signal with and without it, then again with the scrap wet from a hose or spray bottle (tap water shows most of the effect; for salt, about 1/2 cup of table salt per gallon is sea strength). If plywood costs too much: cut a window in the deck panel over the Mini and fill it with closed-cell foam core glassed both sides, the way radomes are built (foam barely touches the signal). Heat is the bigger risk under the deck: the spec sheet gives -22 to 122 F operating (it does not say air or case) and 25 to 40 W of its own heat; owners report it shutting itself off in full sun with no air moving, reportedly near 130 F (forum reports, unverified). Under a sunny deck it would sit in a hot pocket with no breeze. So under the deck it needs a real air path, and an on-deck cover that shades it with an air gap beneath may run cooler than either bare sun or under the deck. Mike, 2026-10-06: under the deck is the cabin, one open space heated by the sun and cooled by the sea, not a closed pocket. Claude: agreed, so the Mini sees cabin air, but the top of the cabin is its warmest air and nothing moves it; estimate 100 to 115 F there on a sunny tropical day (a guess), against the 122 F rating. A small fan (1 to 2 W) blowing cabin air across the Mini's back would likely give enough margin. Have the Pi log the Mini's heat alerts (the Starlink app shows thermal throttle and shutdown alerts). If the deck route fails: a low, rugged cover on deck, not yet picked. *Documents: Build Guide comms section; Electronics plan A13 and sec 6; Instrument Post Guide 7 and 8; BOM 15.8.*

293. Where the hatch and the post go, since the panel layout hangs on both. Mike, 2026-09-26: the hatch can go anywhere, and the post is in the last 12 in of deck and about 6 in wide. The best layout found puts the hatch across the boat at 7.4 to 9.7 ft, just ahead of the pylon, with a 50 W panel each side of it, which costs about 100 W less than any other spot. Four deck measurements decide the rest, and all four want checking before the panels are ordered: deck width at 24 ft (two 200 W panels side by side need 62 in clear inside the 2.5 in edge band, or the stern loses 100 W), the pylon keep out width (36 in or less), deck width at 3.8 ft for the bow pair (about 1 in to spare each side), and confirmation the hatch may sit over that forward compartment. No panel crosses the centerline peak in this layout, which avoids rounding the ridge. The layout is written into Build Guide 4.4 at the best case (2026-09-28). Also to settle with it: the Instrument Post Guide's 30 in keep-out square round the post may reach forward onto the two 200 W stern panels, which run to 24.0 ft. *Documents: Build Guide 3.1, 3.2 and 4.4; Instrument Post Guide 4 and 11.1.*

283. Boat 2's route plan and year. Two plans exist: the Routing Guide (Brunswick, early January 2028) and San Diego Routing (mid-August 2027). A mid-August 2027 start cannot follow Boat 1's mid-November 2027 return, so the San Diego plan's first workable start is mid-August 2028, written in as such. Recommendation: keep the Routing Guide's Brunswick plan as the starting point and move San Diego Routing to Reference once Boat 1's date is firm. *Documents: Routing Guide 1.3, San Diego Routing 1, Science Payload Strategy 1.* Mike, 2026-09-26: wait and see. Not a question again until Boat 1's date is firm. San Diego Routing moved to Reference at v10.0super (2026-09-27), on hold with it.

322. Tabbing widths for the pylon bulkheads and the frame grid (2026-09-28). Build Guide 3.1 ("Tab the grid") says three layers of 17 oz biax "4 in wide, lapping 3 in onto frame and 3 in onto hull". Both cannot be true: a 4 in strip laps 2 in each side; 3 in each side takes a 6 in strip. Mike asked whether 4 in and 6 in biax do enough on the pylon bulkheads (the three wing support bulkheads, Rig Base Two Plate Design sec 5), which meet each hull side over about 20 in (19 3/4 in deep at the ends). Yes. First pick (since revised, below): stepped, 4 in, then 6 in, then 6 in, on both faces at both ends, over a thickened-epoxy fillet, the hull ground to bare glass about 4 in out. Load, if the three bulkheads alone carried a sideways tip to the hull sides (the pylon box also carries it, so this is high): about 50 lb per inch of joint at the governing load (16,200 ft-lb at the deck) and about 150 lb per inch if the mast bends to breaking (46,800 ft-lb, Wing Load Path Recheck finding 2); allow two to three times that at the joint ends. Hold, estimated (the plywood's face veneer tearing is usually the weak part, not the glass): about 800 to 1,200 lb per inch with 2 in laps both faces, about 1,200 to 1,800 with 3 in laps. The Wing Load Path Recheck got the same answer (78 lb per inch against over 1,000). Wider than 3 in adds little: the load goes in near the lap ends. The grind, the fillet and no dry spots matter more than the width. The same 4, 6, 6 schedule fits every grid frame. Outside rules, checked 2026-09-28: Lloyd's small craft rule, first layer at least 2 in each side (as quoted by a naval architect on Boat Design Net); ISO 12215-6, flange 3 times the bulkhead thickness, capped at 3 in, so about 2-1/4 in for 3/4 in plywood (from a summary of the standard, text not read); common practice 2 in minimum, 3 in better. So 2 in and 3 in laps meet them. The weak way is peel: the bulkhead end pulling straight off the hull, worst at the bottom end of each 20 in joint. Width helps little there; a full fillet and more layers help. Peel strength of hand-laid tabbing is not known here. Revised the same day after Mike asked whether one layer is enough: by the numbers, yes, for the load along the joint. One layer of 17 oz biax on each face holds about 300 to 500 lb per inch (the plywood face tears first, so extra layers barely raise this) against about 150 needed at mast break, so about 4 times. The fourth layer above had no number behind it and is withdrawn. Claude's pick now: two layers each face, 4 in then 6 in, wrapped round the bulkhead's bottom corner onto the hull. The second layer is for what the numbers do not cover: a dry spot or bubble in a single 1/32 in layer is a hole straight through the joint, and a thicker tab resists peel better. Mike to say one, two or three layers; the Build Guide 3.1 wording follows his answer. Nothing to do unless Mike says otherwise; then Build Guide 3.1 gets the stepped wording. *Documents: Build Guide 3.1 ("Tab the grid"); Rig Base Two Plate Design sec 5 ("17 oz biax both faces" gets the same schedule).*

324. The rig base under the main bolts: decided 2026-09-30, written into the guides the same day; only the buying is left (tracker). 2026-10-12 (Mike): four more 3/8 in edge bolts, one at each end of each middle angle where plate 1's side edge crosses it; the top view drawing (Reference/Rig Base New Plan Top View 2026-10-12) and Rig Base sec 5 now show 36 edge bolts; 12 of them are the 2 in hatch bolts on hand (tracker). Same day (Mike): the stainless angle sticks come with 12 holes, 3/16 in, 3 in on center in the upright leg; they are the sideways bolt holes, drilled out to 17/32 in. 2026-10-19: all 36 edge bolts are the 3/8-16 x 2 in bolts (30 on hand, 6 to buy); the long answer to "what size bolts everywhere" is in Rig Base sec 5 and the top view's cut list. Every hole in the stainless angles, unfolded, and where to cut the 48 in sticks (four sticks for the 36 in angles, a fifth for the side pieces): Reference/Stainless Angle Holes 2026-10-19.pdf (2026-10-19). The 12 head bars from the 36 in bar, cuts, holes (5/8 in from the upright edge) and how one sits: Reference/Head Bars 2026-10-19.pdf (2026-10-19). Middle angles: 10 bolts, the two holes at 10-1/2 in each side of center left undrilled (they sit behind the head bars); front and back angles: all 12. Rig Base sec 5; top view drawing; which holes: Reference/Middle Angle Bolt Holes 2026-10-12. Mike: long angles 3 x 3 x 1/2 in 6061 aluminum, 2 x 2 x 1/4 in stainless (on hand) everywhere else. Nuts: two bronze nuts per bolt, no jam nuts; so 4 in main bolts at the eight front, back and side bolts and 4-1/2 in at the four corners (thread length sets it), a 316 washer under the first nut at the corners and sides; back row slots 13/16 x 1-5/8 in. Priced list in the recount file: about $590 before shipping and tax. Written in 2026-09-30: Rig Base secs 3, 4, 5 and 7; Build Guide 3.3; Design Decisions R-3.3A and the bolt decision; BOM 15.2; Wing Can Spec Sheet (plate 3 holes and pads). Left: order the parts (tracker row BUY) and release the shop sheet after Mike reads it (item 343). Earlier text kept below. Decided 2026-09-30 (Mike): the middle bulkhead angles are the 2 x 2 x 1/4 in stainless on hand, with the head bars under the four side bolts, which move to 2 in from the middle bulkhead's center; long angles 11-3/8 in; the bolt through both middle uprights 1/2 x 3-1/2 in; jam nuts silicon bronze. Drawings, shop sheet and recount redrawn (all 2026-09-30). Still open: the long angle size (Claude: 3 x 3 x 1/2 in aluminum, one 72 in and one 24 in, $229) and whether the front and back angles stay stainless (0.9 at mast break) or go 3 x 3 x 1/2 in aluminum (2.0, $153 plus 24 edge bolts). About $570 all in with stainless outer angles, $745 with aluminum. v10.1 writes in what Mike decided (Rig Base Two Plate Design secs 3 to 8): the pylon bulkheads glued in, the outer two 36 in apart outside to outside; the middle one tripled with an angle on each face; plate 1 bolted to 2 x 2 x 1/4 in stainless angles on the bulkheads and doublers (no angle rail on a pylon box rim, no webs, no brackets); plates 1 and 3 both 1/2 in; angle under every main bolt, the long angles butted fore and aft between the outer and middle angles; new angle is aluminum; end bolts on every long angle, the inner one up from below into a hole tapped in plate 1; 12 of the 3/8 in edge bolts along each outer angle; the twelve 3/4-10 x 3-1/2 in 316 main bolts stay, with no bolt test; heads at the bottom spot welded to a 2 x 3 in stainless head bar against the angle, nuts on top of plate 3 (this also answers how the heads are held once the rail is gone); only the back row of plate 3's holes are fold slots. Waiting on Mike: (a) which of the three buys in Reference/Rig Base Strength Recount 2026-09-29.md: A (2-1/2 in x 3/8 aluminum, 1/2 in bar, 4 in bolts, $447), B (3 x 3 x 1/2 in, 1/4 in bar, bolts on hand, $481) or C (3 x 3 x 1/2 in, 1/2 in bar, 4 in bolts with a bronze nut and a jam nut, $615; Claude's pick); the jam nut in C is 316, which clashes with the Rig Base rule "never 316 nuts": use a silicon bronze jam nut (made in 3/4-10, 27/64 in thick, same height as the 316 one, so the bolt length figures stand; Albany County Fasteners lists them, 2026-09-30); (b) the 1/4 in 316 corner pads on plate 3; (c) the plate 3 hole pattern as drawn in Reference/Plate 3 Shop Drawing 2026-10-12 (four across front and back, corners included; two each side of the middle bulkhead); (d) 3M 5200 in the clearance hole round each main bolt. The shop sheet draft shows (b) and (c) as firm: settle them before it is released. *Documents: Rig Base Two Plate Design secs 3 to 8; Wing Can Spec Sheet; BOM 15.2 and 15.6; order tracker (new line, Your call).* Notes 2026-09-30 (Claude, checking v10.1 against the session): with the XXS mast every recount figure is 0.8x, so in option C the outer stainless flat legs come out at about 0.9 at mast break, the one part under 1 (aluminum there gives 2.0); the recount file now says so at its top. The stainless angle on hand for the rig base is the two Amazon sticks (the six McMaster sticks are the wing pylon's, item 239); the new layout needs about 114 in of it (two 36 in outer angles and four side pieces of about 10-1/2 in), checked 2026-09-30: the Amazon sticks are 4 ft each (Amazon B0F1KNLHDR, 48 in), so 96 in, about 18 in short on their own; the six 4 ft McMaster sticks (the BOM's "wing pylon angle", and the pylon bulkheads are these bulkheads) are 288 in more. Both lots are for this job, 32 ft on hand against about 9-1/2 ft needed; Rig Base sec 5 now says so. Parts list and cost for C with aluminum outer angles too: about $995 with guesses ($708 for the metal and main bolts), in the recount file, 2026-09-30. Rig Base Two Plate Design sec 3A "Mounting it" says "no tapped holes or inserts" (about the bearing bolts) while sec 5 threads the long angles' inner end bolts into plate 1; word it so they do not read as a clash. Bought 2026-09-30: Speedy Metals 620450 ($524.49: two 72 in sticks of the 3 x 3 x 1/2 in angle, 53 in more than the 91 in needed; the 1/2 x 2 in bar; the 1/4 x 4 in pad stock) and Bolt Depot 2630993 ($328.39: the main bolts, the 1/2-13 bolts including the 24 wood bolts, nuts and washers). Left to buy: the 1/2-13 tap and 27/64 in drill (tracker Buy list).

340. The wet lab drip tray, now there is no leak sensor in it (found at v10.1). A leak caught in a walled tray never reaches the bilge sensors, so a slow wet lab leak shows only when the tray overflows. Options: a drain from the tray to the bilge, or a tray with no walls. Mike's call. *Documents: Flow-Through Wet Lab Design 7 and 12.*

343. Read the welding shop's sheet before it is released. Reference/Wing Can Welder Instructions 2026-10-13 v13.pdf Cut files for the plasma table (2026-10-19, Mike's ask): Reference/Plate 3 Cut File 2026-10-19.dxf (plate 3's outline, 8 round holes 15/16 in and 4 slots 15/16 x 1-3/4 in on layer CUT; can, post and pad outlines on LAYOUT, not cut) and Reference/Plate 3 Corner Pads Cut File 2026-10-19.dxf (the four 4 x 4 pads laid out on Mike's 18 x 4 x 1/4 in bar with their holes and slots; script _make_Plate3_DXF_2026-10-19.py), each with a PDF and PNG; give them to the shop with the sheet. (seven US letter pages; sources and drawing script in Reference/_shop_instructions_src/; every earlier sheet is in Archive/). The welder's copy is rewritten in plain words (2026-10-02, Mike: no jargon), named Wing Can Welder Instructions; sources welder.html and rev3_drawings.py in Reference/_shop_instructions_src/. Rev5 (2026-10-01): no machining; every flat part, holes included, CNC plasma cut, the lip holes before welding; the bearing bedded by Mike on thickened epoxy (Mike: simplify so one shop can do it all). Rev4 used the 21 in tube uncut, so the lip face is about 21-1/4 in above plate 3, and the post is 9-1/4 in (Mike). Rev3 took in Josh's review (Reference/Shop Instructions Rev2 Review 2026-10-01.docx) and Mike's answers of 2026-10-01: Josh Johnston (918-606-0099) is the shop's contact; no base ring; slots 15/16 x 1-3/4 in; lip holes 3/4 in; bearing seat from 16.30 in dia; the mast plate disc cut out by plasma or waterjet before the bore is finished; a cut list, top view, dimensioned elevation, lip section, weld map, clamping and separate tools for steel and stainless. Not taken from the review: the mast plate stays 304 (decided 2026-09-29) and the corner bolts are already 4-1/2 in. Left: Mike's read-through before release. Hand-holes now two 7 x 9 in ovals with bolted covers, at port and 150 degrees (2026-10-02). The corner pads and the 12-hole pattern wait on the rig base buy (item 324). The three rig base drawings (Plate 3 Shop Drawing 2026-10-12, the top and side views of the same date) now carry the 15/16 x 1-3/4 in slots and no base ring, matching v11 (2026-10-08). *Documents: the shop sheet; Wing Can Spec Sheet.*

2B. Look at a part and say what it is

374. Parts bought in early October that no document names (Claude, from the order mail, 2026-10-06 to 10-08). Mike to say what each is for: (1) a TICONN IP67 box ($68.39, with the Flipsky, Amazon 114-2434294-4539414; maybe the second drogue box, since the QILIPSU went back Oct 1); (3) two more Taidacent RS-12V/2S surge modules bought Oct 7 for the DO sensor and SBE 45 lines (no guide puts surge parts on those lines); (4) a second AS3935 lightning board (Playing With Fusion SEN-39003, $34.91, Oct 6): ANSWERED 2026-10-14, Mike is wiring it into the detector mini-box; see item 420; (5) two Pi GPIO screw-terminal boards ($31.76, Oct 6); (6) a Winford BRK2X6-L-FT board ($14.45, Oct 3), beside the BRK2X6-L-DIN the battery taps use; (7) a MECCANIXITY 12-pin 6 in ribbon ($6.19, here Oct 6): is it the 12-pin female-to-female ribbon the Battery Box guide still lists to buy (Amazon B07L9Q3R2K)? *Documents: BOM; Battery Box Building Guide Parts List; order tracker.*

367. The Abireiv outdoor Cat6 cables look shielded; the docs say unshielded (Claude, 2026-10-03, from Mike's photo of a 10 ft one). The plug has a metal shell, which normally means a foil or braid shield inside (inferred, not confirmed). Wire and Cable Buy List B2 says outdoor Cat6 is unshielded so no shield brings a metal path into the hull; that was written before the surge protectors moved to the board near the deck, wired to the lightning copper (item 359). Claude's view: shielded is fine on the deck legs, since each one ends at its surge protector, which is where a shield is meant to drain; the inside legs down to the switch box stay unshielded (B3). Check: cut the jacket back an inch on scrap or read the jacket print for FTP, STP or S/FTP. Salt: the jacket (UV-rated, direct burial) is fine wet; the plug ends are the weak point, so every plug sits inside the hull or under the device's waterproof cap, never bare on deck. *Documents: Wire and Cable Buy List B2; Electronics plan A6a; Lightning Guide 7.4.*

318. Three parts bought 2026-09-26 and 27 that no document names. (1) Kenhihi 6 AWG tinned silicone wire, 10 ft red and 10 ft black, $35.98 (Amazon 112-2902556-7813006, with the release trunk 14/4). (2) A 169-piece bonded seal washer kit, M6 to M24, $20.61, here Sep 27; Claude's guess: for the M20 x 1.5 barbs bought Sep 22. (3) A 5-pack of 1-1/4 x 1-1/4 x 1 in PVC reducing tees, $16.65, bought with the DO chamber bushings and unions; the chamber as written uses the plain 1-1/4 in tees on hand. Also bought 2026-09-28 and 29 with no document line: (4) a YONICO 1/8 x 5/16 in slot cutter router bit, $16.95; (5) eight 1/2-13 x 2 in 18-8 bolts and 25 304 nuts, $23.80; (6) a US Stainless 316 5/16 in part, $9.89 (name cut off in the mail); (7) six VAMRONE 4 in aluminum DIN rails, $6.64; (8) a QILIPSU UL94-V0 16.4 in box, $82.15 (probably the second drogue box). Say what each is for, and it gets its line. *Documents: order tracker (Do next, Order log); BOM.* ---

Closed at v10.5 (written into the v10.5 guides, 2026-11-09)

Full text kept as it stood when written in. Items left with an "At v10.5" note in Parts 1 and 2 were partly written in; the note says what is left.

535. No desoldering: the central node and Release Node B CAN boards (Mike, 2026-11-08: "I can't decenter like that, it's not possible, so probably skip ideas like that"). The Central Node and Release Node B box plans still say to unsolder each CAN board's 4-pin header and solder on a 0.1 in screw block. Mike cannot do that. Those two boards need a no-solder way that still meets the release-logic rule against push-on pins (Electronics plan sec 4), or a yes to treat the CAN board's logic header like the wet lab's (a ready-made plug, zip-tied and glued). Claude's pick for a ready-made plug with thicker wire: a 4-pin 0.1 in female plug to Grove cable, 24 AWG, with the Grove end cut off (Amazon B0DGGJKNTS). DECIDED 2026-11-08 (Mike: "No, I will not unsolder the CAN board. I will put a header connector on it. And I'd like one that stays on. If not, I'll zip tie it on, and I'd like it to be 24 gauge"): each CAN board keeps its soldered header; a ready-made 4-pin plug with 24 AWG wire goes on it (the Grove cable above, Grove end cut off), zip-tied lengthwise over the plug and around the board, a dab of silicone, a paint dot at pin 1 on plug and board. No plug that locks onto a bare header exists (searched 2026-11-08), so the zip tie is the hold. This overrides the release-logic rule against push-on pins for these two CAN board headers. Added to the order tracker Buy list. To write in: the Release Node B box plan (drop the unsolder and screw-block steps; the Central Node plan is done, 2026-11-09), Electronics plan sec 4 and A15. *Documents: as named; order tracker (done).*

534. Flipsky plug types and lead sizes (Claude, 2026-11-08, from Mike's "research what size they are with flipsky"). COMM: JST-PH 2 mm, 8-pin; CAN: JST-GH 1.25 mm, 5-pin (found: Flipsky's 75100 Pro V2 manual, same board family, in Reference/Flipsky and ME1616 Research 2026-09-24.md; the PH and GH leads on hand fit). Motor sensor (hall) plug: JST-PH 2 mm, 6-pin (found: the usual VESC hall port, and Flipsky's own hall adapter is sold as "JST 2.0mm"). Servo plug: JST-PH 2 mm, 3-pin (found: Flipsky's own PPM cable page, "JST-PH 3pin 2mm pitch"); switch plug the same (inferred from Mike's photos). Lead wire size: Flipsky publishes none on any of its cable pages (sensor wires, CAN cable, PPM cable; checked 2026-11-08); about 26 AWG on the PH leads and 28 AWG on the GH lead (inferred, the usual sizes). Largest the pins take (JST): PH 24 AWG, GH 26 AWG. Ready-made 24 AWG PH leads, found 2026-11-08: COMM (8-pin) Analog Devices CABLE-PH08 at DigiKey (PHR series, 2 mm, 24 AWG, 200 mm (7-7/8 in), loose leads, $5.17, 542 in stock, DigiKey Marketplace item, so its own shipping may apply); the 6-pin sensor plug CABLE-PH06, same family; 3-pin (servo, switch) Pololu 24 AWG (a new seller). CAN (GH, 26 AWG max): LATTECH 5-pin GH both ends 26 AWG (Amazon B0CDGMS4L6, cut in half, 1 to 2 in leads) or a 20 cm (8 in) 26 AWG silicone GH extension (Amazon B0GS392JPF, if offered in 5-pin). For Boat 2; nothing bought. Box plan page 1 updated with the plug types. *Documents: VESC A Box plan (done); Electronics plan A7 at the next write-in.*

533. Boat 2 VESC A box: every signal joint on one DIN rail (Mike, 2026-11-08: "for boat 2, would like a better way to connect all the resistors, caps, and stuff. This way was messy"; "Can you layout box like that?"). Proposal drawn as pages 5 and 6 of the VESC A Box plan: a 35 mm DIN rail about 5 in long along the gland side, 16 screw blocks (the wet lab box's kind) in three groups under their glands (C: CAN 0V, CANL, CANH; S: 5V, SIN, ADC1, GND, ADC2, COS, TEMP, T GND; U: RX, TX, 3.3V, PPM, SV GND), cable cores on the gland-side screws, the Flipsky's plug leads and the resistor legs on the other side (10k sin to ADC1, 20k ADC1 to GND, 20k ADC2 to GND, 10k cos to ADC2, 10k 3.3V to PPM). Same wires and pins as Boat 1; no splices or lever nuts; thin plug leads in ferrules, folded double, tied down within 2 in of the plug, a dab of silicone on each plug; the switch plug keeps its own short jumper. DECIDED 2026-11-08 (Mike: "Yes"). Parts are on the shelf (inferred from the tracker): DIN rail (VAMRONE 8 in rails, 12, or the T&G rails), blocks from the MELIFE or Erayco screw kits, or the ST2-2.5 push-in blocks (no screws, easier for big fingers; ferrule on each thin lead), and the resistors. Nothing to buy. Boat 2 only. *Documents: VESC A Box plan pages 5 and 6 (done); Electronics plan A7 and BOM 15.5 for Boat 2 on a yes.*

531. The Orion-Tr's on/off pair may be 16/2 or 18/2, not 14/2 (Mike, 2026-11-08: "why 14/2 from central? 18/2 or 16/2 ok?"; Claude: yes). The pair from central node relay channel 10 to the Orion-Tr's remote terminal on the backup battery board carries only a few milliamps through the relay's contact (Electronics plan sec 4.1 relay table, "a few milliamps"; Wire and Cable Buy List C6, "almost no current"). 14/2 was chosen only so the backup board used one wire (Mike, 2026-10-15), not for current. Any jacketed tinned 2-wire works: 16/2 if the 16/2 roll has about 17 ft left after its branch lines, else 18/2. Central node entry 16 becomes a sealant-filled PG9 in a 5/8 in hole, like the other 16/2 entries, in place of the PG11 in a 3/4 in hole (an oval duplex does not seal in a PG7). The Orion-Tr's remote plug takes the smaller wire; a ferrule on each end. Drawn in the Backup Battery Board Changes plan. At the next write-in: Electronics plan A3 entry 16 and A10, Wire and Cable Buy List C6 and the glands line, Central Node plan. *Documents: Electronics plan A3, A10; Wire and Cable Buy List C6.*

530. Release Node B: block 1 and its jumper dropped (Mike, 2026-11-08: "yes", to Claude's "drop block 1 and its jumper"). Block 1 only existed to feed the fuse, which is gone (item 526). Gland 2's red now lands straight on the 24 V bar and converter G's red moves to that bar's spare screw. The strip is 14 blocks: 1-3 24 V bar (1b gland 2 red, 2b relay DC+, 2t relay COM, 3b converter G red in, 3t surge diode, 1t spare), 4-9 0 V bar (4 gland 2 black and the surge diode, 5 gland 1 black and converter G black in, 6 the surge part PE and relay DC−, 7 the CAN board GND (bottom) and Nucleo GND (top), 8 MOSFET 1 GND (bottom) and DC− (top), 9 the same for MOSFET 2), 10-12 release bus (10t relay NO, 10b box 1 release cable +, 11b box 2 release cable +, 11t and 12t the MOSFET DC+ leads), 13-14 horn returns (box 1 and box 2 release cable −, MOSFET OUT−). This renumbers item 527's blocks one down. Done 2026-11-08 in the Release Node B plan (all five pages) and its long-form data. *Documents: none beyond the plan.*

529. Say release, not fire (Mike, 2026-11-08: "Don't like the word fire for this"; "The word fire should be used to refer to something aflame, or to termination of employment"). For the drogue lids and every other release, the docs say release, let go, open or trigger, never fire, fires, fired or firing; the word stays only for something burning (a battery, lightning damage). Done 2026-11-08: the Release Node B box plan (its "fire pair" cable is now the release cable to each drogue box) and the rules file. At the next write-in: every guide that uses the word for a release (Transom Drogue Box Guide, Electronics plan, Compute Bay Plan, Design Decisions, Steering Handbook, System Settings Sheet, Routing Guide, Build Guide, Bill of Materials, Glossary, Wire and Cable Buy List, Box Wiring Sheets) and the Central Node box plan. *Documents: as listed.*

527. Release Node B's 0 V bar: six blocks, not nine (Mike, 2026-11-07: "Too many ground blocks. blocks 5-13 can be 5-10 (remove 3)"). The strip is now 15 blocks: 1 in, 2-4 24 V bar, 5-10 0 V bar, 11-13 release bus, 14-15 horn returns. The twelve 0 V wires fill both screws of all six blocks, one wire per screw: 5 gland 2 black and the surge diode; 6 gland 1 black and converter G's black in; 7 the surge part's PE and relay H DC−; 8 the CAN board GND (bottom) and the Nucleo GND (top); 9 MOSFET 1 GND (bottom) and its DC− (top, 12 AWG); 10 the same for MOSFET 2. The release cables to the drogue boxes land on 11b and 14b (box 1) and 12b and 15b (box 2); relay NO on 11t. Done 2026-11-07 in the Release Node B plan (all five pages) and its long-form data. No guide gives this box's block count. Renumbered one down by item 530. *Documents: none beyond the plan.*

526. No inline fuse in either release feeder (Mike, 2026-11-07: "yes, drop the fuse", on Claude's "drop it" for Release Node B's fuse J). Each release feeder (line 2 for Release Node B, line 4 for release bus A) is a 12/2 on its own 30 A auto-reset breaker on the backup-fed bar. A fuse in that feed would have to pass the burn current (12.5 A per horn, 25 A with both), so it would be about the size of the breaker and protect nothing more, while adding one more part that can blow or corrode open and stop a release (the rule that every backup keeps the mission going). Release Node B: one 12 AWG red jumper from block 1 top to block 2 top, cut from a 12/2 offcut, in place of the FHAC0002ZXJ holder (then block 1 and the jumper went too, item 530). The central node's release feeder already had none drawn. Done 2026-11-07: the Release Node B plan (all five pages; its page 5 now also draws every cable core from its gland to its screw) and its long-form data, the Central Node plan's open list, and the tracker's FHAC0002ZXJ row (holders on hand, no job). At the next write-in: Compute Bay 10.3 (drop the Open line on the inline fuse), Electronics plan A15 (contents: drop "fuse"), Box Wiring Sheet A15 (the FUSE box and "24 V, fused" label, "its own fuse" in the text), Bill of Materials release-channel parts (drop the FHAC0002ZXJ holders). This settles the mismatch lists' (a) (item 352 and 353). *Documents: Compute Bay 10.3; Electronics plan A15; Box Wiring Sheets A15; Bill of Materials 15.8.*

525. VESC A motor sensor divider: always fitted, no bench check (Claude, 2026-11-06, from Mike's "please research the spec sheet"). The ME1616's sin/cos sensor is an RLS RMB29 (analogue sinusoidal, RMB29AC). Its data sheet (RLS RMB29D01_07, page 4, saved as Reference/RLS RMB29 Datasheet RMB29D01 07.pdf): supply 5 V plus or minus 5 percent; signal amplitude 1.1 V plus or minus 0.2 V, drawn as 2.2 V peak to peak; both signals centered at 3/5 of the supply, 3.0 V at 5 V (directly known). So each signal runs about 1.9 to 4.1 V, worst case about 4.45 V; the Flipsky's ADC1 and ADC2 take 3.3 V at most. The Build Guide (sec 5.1, Sensor harness) has the center wrong at 2.5 V and the tops at 3.6 V. Decided: the 10k and 18k divider is always fitted on sin and on cos, and the bench check (5 V on the sensor, read the tops) comes out. After the divider each signal is about 1.2 to 2.6 V (1.9 V plus or minus 0.7 V), worst case top about 2.9 V. The 28k load the divider puts on each output is light; RLS gives no load limit (inferred fine). Written into the VESC A Box plan 2026-11-06. Changed 2026-11-06 to 10k and 20k (Mike: "cant find 18k"): each signal then runs about 1.3 to 2.7 V (2.0 V plus or minus 0.7 V), worst case top about 3.0 V, still under 3.3 V; written into the box plan. No filter capacitors (Mike, 2026-11-06: ordering them "will delay things"; Claude agreed, small value): the September research file's 0.01 uF from each joint to ground stays out; the sensor wires kept apart from the motor leads and the firmware's own sensorless fallback cover the same risk. To write in: Build Guide 5.1 (Sensor harness) and the Flipsky bench check paragraph that repeats it, Electronics plan A7 if it says "if needed". *Documents: Build Guide 5.1; Electronics plan A7; VESC A Box plan (done).*

524. The wet lab box: its Nucleo is bought, and its CAN surge part goes on its own rail (Mike, 2026-11-06). (a) "ken got nucleos from digikey, so stop asking": the wet lab box's NUCLEO-G431KB is bought (Ken, DigiKey; price not on record). Done 2026-11-06: the Wet Lab Box plan's parts page and the tracker (Buy list row marked bought; the Parts row now x3). At the next write-in: Bill of Materials 15.8 and the wet lab row, Electronics plan A18, Flow-Through Wet Lab Design sec 2 and Box Wiring Sheets drop "to buy". (b) "Can surge is on different rail (no room)": as built, the Taidacent RS-12V/2S CAN surge part (E) is not on the main DIN rail but on a short rail of its own. Its wires are unchanged (IN from gland 1, OUT to the CAN board, PE to block 2 bottom). The plan's new page 6 (the rail close-up) leaves it off; it stands upright on its own short rail at the left end of the plate (Mike's photo, item (d)), drawn so on pages 2 and 5. (c) Wire sizes inside the wet lab box (Mike, 2026-11-06: "we have lots of 18 guage single wires 22awg singles too"): 22 AWG for signals and the 1 A and 2 A feeds; 18 AWG for the main 24 V path, which the plan had partly at 16 AWG and partly, wrongly, at 22 AWG: the link from block 5 to F1, F1 to relay COM3, NO3 to block 12, and the two links from block 3 to blocks 16 and 19. Up to 10 A (the XWST's limit; the line's 15 A breaker upstream), runs of inches; 18 AWG hookup wire is good for that unless rated only 60 C (inferred). The gland 2 feed stays the 16/2 cable. The XWST's own leads reach the rail (Mike, 2026-11-06: "I thikn xwst leads are long enough to reach din rail"), so they land on blocks 1, 2 and 4 as they come, no added wire. Done 2026-11-06 in the Wet Lab Box plan pages 4 to 6. (d) As built, from Mike's photo of the plate (2026-11-06): the CAN surge part stands upright on its own short rail at the left end of the plate, above the main rail. The CAN board sits left of the 5 V converter (page 2 has them the other way round). The relay board's COM and NO screws are on its top edge, away from the rail, and its input strip reads DC+, DC−, IN1 to IN8, left to right. The opto board (BUCCK_817_8 V1.0) has a + and a − screw for each input, no common: the plan's "IN common to 21t" becomes 1− to 5− joined by short 22 AWG jumpers, one wire on to 21t; its output strip reads 08 to 01, GND, VCC. Done 2026-11-06 in the plan's wiring text (pages 3 to 6); pages 2 and 5 redrawn to the photo the same day (Mike: "maybe redo pdf per this photo?"). (e) One 0 V group, blocks 16 to 23 (Mike, 2026-11-06: "It is connected by a short wire so there is no separation that i can see"): the returns (16-18) and the sensor 0 V (19-23) are one bridged group; the 18 AWG link from block 3 to block 19 is dropped (19b spare); block 3 to block 16 stays. Done in the plan the same day. (k) 3 holes: the 24 V feed goes in split gland C, port C3 (Mike, 2026-11-07: "24v fits in C"), so the PG9 is gone; C4 is the only plugged port. The docs' rule (Electronics plan gland table) keeps oval 16/2 out of split ports because a flat jacket can leave gaps at the sides of a round seal; Mike's fit says it seals. Done in the plan the same day. (j) Three split glands, 4 holes (Mike, 2026-11-07: "yes, 3 split glands, please use colors on 12/22 and 4/18 cables"): this replaces (i)'s gland list. Gland 1 (PG9): the 24 V feed. Split gland C: C1 the pumps' 4/18 (white Iwaki + 10b, green Kamoer + 11b, red Gulper + 12b, black shared − 16b), C2 the valves' 22/12 (purple 8b, red 13b, orange 14b, brown 15b, black 17t, gray 18t, yellow 30b, green 31b, blue 32b, white 33b, pink and beige spare), C3 and C4 plugged; both shields to 23t. Split A: CAN drop, flow meter, pressure sensor, Celsius probe. Split B: DO sensor, its FTDI cable, SBE 45, its FTDI cable. The 4/18 and 22/12 core colors are Claude's pick from the usual sets (the cables' own color codes are not on record); if they differ, the screws stay the same. Holes: PG9 5/8 in; PG25 1-1/2 in (PG25 thread is 37 mm, 1.46 in). The valve cable must be 0.30 in or less to seal in a port; if bigger, it takes its own PG9 or PG11. A third Altelix 4-port is needed: two are free from the dropped aft junction box; whether one is left from the 5-pack is not known. Every incoming wire lands on a rail screw except the CAN drop's white and blue (on the CAN surge part). Done 2026-11-07 in the plan, pages 1 to 8 (new page 7, the cables in; new page 8, every cable wire). (i) Fewer holes (Mike, 2026-11-07: "yes, split glands, combine pumps and valves"): the wet lab box's bottom wall goes from 14 glands to 5. Gland 1: the 24 V feed, 16/2, own PG9. Gland P: the three pumps on one 4/18 shielded cable (on hand, Wire and Cable Buy List C4), Iwaki +, Kamoer +, Gulper +, one shared − to 16b (one pump runs at a time), own PG7. Gland V: both valves on one 22/12 shielded cable (on hand, C1), 10 cores used, 2 spare, own PG9. The pump and valve leads join P and V outside the box with glue-lined heat-shrink butt splices (on hand); both shields to 23t only. Split gland A (Altelix PG25 4-port): CAN drop, flow meter, pressure sensor, Celsius probe. Split gland B: DO sensor, its FTDI cable, SBE 45, its FTDI cable. The two split glands are the pair freed from the dropped aft junction box. Each split port takes one round cable 0.15 to 0.30 in; the cables' sizes are not on record (Claude's guess: they fit). Done 2026-11-07 in the plan pages 1 to 6 and the tracker. At the next write-in: Electronics plan A18 entries. (h) As built, the 0 V blocks are two bridged bars with a divider (16-18 and 19-23), joined by one short 22 AWG wire from block 18 top to block 19 bottom (Claude, 2026-11-07, from Mike's photos); this replaces (e)'s single bar. Drawn in the plan pages 2 to 6. (g) Relay board screw order, from Mike's photos of 2026-11-07: each relay's three top screws read NC, COM, NO left to right (printed on the board); page 5 had guessed NO, COM, NC and is fixed. The wiring itself is unchanged (COM and NO used, NC empty). (f) The XWST's two black leads split (Mike, 2026-11-06: "one to 2 and one to 17"): black in on block 2 top, black out on block 17 top (beside gland 6 common), so the pump and valve current goes straight back to the converter; the 18 AWG link from block 3 to block 16 is dropped (3t and 16t spare). Rests on the XWST's two blacks being joined inside (non-isolated, inferred from similar listings); the CAN drop's black on 21b ties the group to the boat's 0 V either way. Done in the plan the same day. *Documents: Wet Lab Box plan pages 1, 2, 4, 5, 6; tracker; at the write-in BOM, Electronics plan A18.*

521. The SN65HVD230 CAN boards came with their pins already soldered on (Mike's photo, 2026-11-05: "Wet lab. Can board has header, not holes for solder, what is best to do?"; then, on the plug, "yes"). DECIDED 2026-11-05 and written in the same day: Electronics and Wiring Plan sec 4 (central node), A15 (Release Node B) and A18 (wet lab box); Bill of Materials (the CAN boards, the RLECS leads with their link); the Wet Lab Box, Central Node and Release Node B box plans (rebuilt); the order tracker's RLECS row. The four Alinan boards on hand have a 4-pin male header soldered in on the logic side (3.3V, GND, CAN RX, CAN TX, in that order) and a blue 2-way screw block already fitted for CANH and CANL, with two bare pins beside it. The wet lab, central node and Release Node B box plans all say to solder a 0.1 in screw block onto the pin row, which assumes bare holes. Wet lab box: push one RLECS 4-pin female Dupont lead (bought Oct 6 for the GPS; a 6-pack of 7.9 in leads with a plug at each end, https://www.amazon.com/dp/B0DGGCM12Z) onto the header, zip-tie it lengthwise over the plug and around the board, and add a dab of silicone or hot glue, the way GPS A is done (Compute Bay Plan, GPS A). Cut the plug off the lead's far end and strip the wires; they go under the Nucleo carrier's screws with ferrules (3.3V to 25b, GND to 22t, CAN TX to D2, CAN RX to D10, per the plan). No header removal. Allowed because push-on pins are banned only in release logic (Electronics plan sec 4), and the wet lab box is not release logic. If the plug ever shakes off, the box runs each burst on its own (the solo burst, item 522), so the science goes on. The 120 ohm resistor (marked 121, just below the CANL and CANH pins) still comes off (item 500 (a)). Central node and Release Node B: they fire releases, so a push-on plug is not allowed there; take the header off and solder on the screw block, as their plans say.

523. The tape on inside copper lightning joints: the XFasten self-fusing silicone tape on hand (Claude, 2026-11-06, from Mike's "is this good to wrap copper to copper lightning joints? Anything better?"; Claude's pick, standing unless Mike says otherwise). The Lightning guide says every joint is "bolted, bright metal, pasted and sealed" (sec 5.3) and "then tape the joint" (sec 6.1), but names no tape. Use the XFasten silicone tape bought 2026-08-01 (order log): it fuses only to itself and leaves no residue, so a joint can be unwrapped, metered and rewrapped at each refit, as the guide asks; it stays soft and takes about 500 F (its listing). Not chosen: rubber self-amalgamating tape (3M 130C under vinyl), which seals odd shapes a little better but goes gummy and is hard to get off after years; liquid tape and 5200, which cannot come off for the refit check. How: No-Ox-Id A-Special between the faces, bolt tight, wipe the paste off the outside; round off sharp bar corners and bolt ends so they cannot cut the wrap; stretch the tape to about twice its length, half-lap, starting and ending about 1 in past the joint on bare bar, covering the bolt head and nut; press the tail down. Outside joints (the wing strap lap, the deck and mast joints) stay bedded in 5200 as the guide says. *Documents: Lightning Ground System Guide secs 5.3 and 6.1 (name the tape and the wrap).*

522. Keep the wet lab running when its CAN link dies (Mike, 2026-11-05, on item 521's "you lose science, not the boat": "Don't like that logic, still want pumps and stuff if can dead, we have RS232 and 485, right?"; then "I think yes, but please consider it all in detail."; then, on the solo-burst rule, "yes"). DECIDED 2026-11-05 and written into the guides the same day: Flow-Through Wet Lab Design sec 10 (the home: "The solo burst" and "Pi A's side") and its failure table, System Settings Sheet (wet lab line; wet lab box silence rule), Electronics and Wiring Plan A18, Box_Wiring_Sheets_v10_4a (wet lab notes, PDF rebuilt) and Reference/Wet Lab Box 2026-10-14. Left to do: a software ticket in the software repo for the wet lab box and for Pi A. The worked-out rule as decided: The serial lines can't carry orders as wired: the RS-485 (DO sensor) and RS-232 (SBE 45) lines only pass through the wet lab box on screw terminals, on their way to the USB hub box and Pi A on their FTDI cables. They never touch the Nucleo. They do keep the science data flowing to Pi A with CAN dead, since they don't use CAN. Claude's worked-out rule, no new parts or wires. Pi A already powers the whole wet lab line through central node relay channel 2 about a minute before each burst and off after (System Settings Sheet, wet lab line), and the central node is on the control bus, not the house bus, so that switch works with the house bus or the box's own CAN link down. (a) Power-on with no word from Pi A for 60 s: the box runs one normal burst by itself (Rule 1 order: drainback, fill and de-bubble, flush, measure, dose if due, pump off and valve 2 shut together), from the last settings Pi A sent, kept in its memory (bench defaults until then). Then all relays off; it waits for the next power-on. A restart of the box counts as a power-on. (b) Dosing carries on: the box keeps its count of bursts since the last dose in memory, so the every-6-hours dose continues (settings give the dose every N bursts, N set from the burst rate). (c) On its own it never moves valve 1 and never runs the Gulper (the blast stays a shore order). The channel rules stay. No flow at the meter: pump off, end that burst, next burst starts with the cough (Rule 2). (d) Nothing lost, only late: the box keeps a short record of each burst it runs alone (intake temperature, flow, line pressure, valve stroke times, dose given) and hands it to Pi A when CAN is back. Room for weeks of bursts is a guess; it depends on the program's size. (e) Pi A's side: it keeps switching channel 2 on the burst schedule (shore still sets the rate) whether or not the box answers; when the box is silent it holds the power on for the full solo burst plus a margin (about 16 min), reads the DO sensor and SBE 45 in the measuring window timed from power-on (not the whole burst, to spare the DO sensor's cap), and flags those readings until the box's record arrives. (f) Leaks: Pi A always answers a bilge alarm by cutting channel 2 (valve 2 springs shut), not by a CAN message, so it works with CAN dead; after a leak alarm the line stays off until shore says. (g) Silence in the middle of a burst keeps today's rule: all relays off. That is what a crashed Pi A looks like, and then no one is watching the bilge. Cost: one burst; the next power-on runs alone if CAN is still out. (h) Half-working links: if Pi A hears nothing back but the box hears Pi A, Pi A sends "run this burst on your own"; if the box hears nothing but Pi A hears the box, the box runs alone and Pi A gets every reading live. If CAN comes back during a solo burst, the box finishes it, hands over its record, and goes back to Pi A's orders; a stop from Pi A always wins. (i) Gap accepted (Claude's opinion): if Pi A dies in the minute after switching the line on, the box runs one burst with no one watching the bilge; that needs a hose to burst in the same 14 minutes. Unchanged: with Pi B in command, the science pauses (Compute Bay 4.3); the central node remains the wet lab's only power switch (a no-backup part, its own question). The plug on the CAN board (item 521) is fine with this rule, since a loose plug no longer stops the science.

520. The TICONN 5.9 x 5.9 x 3.5 in link is wrong; the wing box fits that box (Claude, 2026-11-04, from Mike's "Do we need the room for the wing box?"). Nothing left to decide. (a) Wrong link, nothing to decide: Amazon B0B87THLGC is the TICONN 5.9 x 3.9 x 2.8 in box (its Amazon title; manuals.plus agrees), not the 5.9 x 5.9 x 3.5 in the guides name for the wing box and the Iridium boxes. The 5.9 x 5.9 x 3.5 in box is [Amazon B0B87VR84G](https://www.amazon.com/dp/B0B87VR84G). Order tracker fixed 2026-11-04 (wing box and Iridium box rows, Buy list). (b) The wing box's room: the 5.9 x 5.9 x 3.5 in box is enough (Claude, 2026-11-04, from the wing box plan's layout, after Mike's "Look at your layout, it either needs more room or not"). Flat on the plate, the layout fits: the 4.8 in rail (end stop, terminals 1 to 9, the three surge modules, end stop) sits on a plate about 5.2 in square with about 0.4 in to spare, and the modules' IN ends stand about 1 in above the bottom wall's glands. Pi B's tap needs no more rail: its CAN pair lands with the Cat6's blue pair under M3's OUT screws, in twin ferrules (two wires, one ferrule), and its ground on a spare ground block (4 to 9). Its gland, a PG7, goes in the upper row above gland 5, where the drawn rows leave room. Depth: one-module RS-485 surge protectors from other makers are about 2.2 in deep off the rail (EWIMAR 17.5 x 90 x 57 mm; Phoenix MT-RS485 54.9 mm deep); the Taidacent lists only its 18 mm width. Back wall, plate posts, plate and rail add about 0.7 in, so about 2.9 in of a box 3.5 in deep outside: it closes with about 1/4 in to spare (inferred). So no bigger box; the spare TICONN idea is withdrawn. Buy the 5.9 x 5.9 x 3.5 in box at the right link (a). *Documents: Electronics plan A11 and A17; Wing Power System 8.7; BOM; Box Wiring Sheets A11 and A17 (and the top-level copy); Box_Plans_v10_4a/Wing Box v10.4a.pdf; Box Parts With Photos 2026-10-15; the order tracker.*

513. Mike's answers to the readability rewrite questions (Mike, 2026-11-02). Done 2026-11-02, written into the guides. (a) The wing spar question is past: Boat 1's foam stack is complete on the spar, waiting for its skins (Mike: "The foam of the wing is complete, waiting to glass it"), so the spar-hole sanding note added earlier the same day came back out (Wing Construction Guide Stage 1 step 3, Stage 6, Appendix A). (c) Fold hinges: no pull test; the four White Water hinges fold the rig (Rig Base sec 6, BOM 15.6, Build Guide 3.3.1); this closes the hinge item of 2026-09-26. (d) Hydrophone fin: glued and glassed on before barrier day, no bolts (Science Payload Strategy sec 5 steps 11 to 13; Bottom Painting Guide Step 0). (e) Copper strips: on with their glass straps before both the barrier coat and the paint (Mike: "before both"); the barrier and paint run up to the masked copper, and under the strip the 5200 keeps the water off the hull (Bottom Painting Guide Step 0 and steps renumbered; Lightning Guide sec 5.5; Build Guide sec 2). (f) Line cutter plate: kept, a 316 plate bought cut to 3 x 8 in and drilled to the Spurs pattern (Glossary; Design Decisions). (g) Shaft spark gap: kept as it is (Lightning Guide sec 9.2). (h) Steering rod eye on top of the tiller arm (Steering System Handbook sec 4). (i) Wing glue-up root-up only; the root-down text is out; it needs about 10 ft clear and a hoist or gin pole (Wing Construction Guide Stage 13 step 1). (j) Motor heat limits stay 212 F derate, 248 F off, 194 F shore alert (Mike: a 221 F shutoff "sounds too conservative"); the Settings Sheet now says why the sensor board's 221 F connector rating does not bind (System Settings Sheet sec 2). (k) Boat 2 steering gathered into a closing sec 9, so secs 1 to 8 are Boat 1 only; old 5 is 9.5, old 6 to 9 are 5 to 8 (map _v104a_work/rewrite/maps/Steering_System_Handbook_2.md; 7 pointers in other guides and 5 here fixed). (l) Spain's October steps are done (Mike: "yes"): research consent filed, flag and papers settled, PLOCAN and the Capitania written to; the to-do lines came out (Boat 1 Route secs 4 and 5; Science Payload Strategy sec 1). (m) The Trinidad 75 came: FedEx 877570763577 delivered it to Viatrax in Claremore 2026-09-25, signed for by J. Johnston (FedEx tracking page, read 2026-11-02); Bottom Painting Guide, BOM 15.3, Build Guide sec 2 and the order tracker updated. (n) The root ribs' socket gap was filled as the ribs went on (Mike: "Root ribs gaps were filled"); item 365 closed (Wing Construction Guide Stage 6). (o) The hydrophone fin as cut is used (Mike: "fin should work fine"); item 371 closed (Science Payload Strategy 5; Design Decisions R-10.2B). (p) Copper strips go on before the barrier coat (Mike: "so we will install copper before barrier coat"), as (e) already says. (q) Camera window: the inboard cap is the second seal (Mike: "ok, makes sense"; item 512 closed). A 1/4 in G10 ring, 2-1/2 in across, glued round the tube's inner end with four captive silicon bronze #8-32 nuts; the cap held by four of the bronze screws on hand, on afloat except while the camera is swapped. Mike: "How about a gland?": the camera cable and the UV-C cable pass through an Altelix PG25 4-port split gland from the 5-pack, since the camera cable keeps its plug (Axis's cable ends in a plug, so it will not pass a plain gland); the gland is bedded in 5200 because its nut is wider than the 1-1/4 in bore. If the glass breaks, the tube floods and stops at the cap (under 1 psi, about 3/4 lb): the camera is lost, the boat carries on. Nothing to buy: 20 silicon bronze #8-32 screws and 20 nuts came from Bolt Depot (2026-08-31). (Underwater Camera Port Guide rules, parts, secs 2, 4, 6 step 8, 7 step 5, 9; BOM camera row.) (r) No collars on the drogue U-bolts (Mike: "drogue ubolts won't be used", then "no collars on ubolts", 2026-11-03); item 408 closed (Transom Drogue Box Guide 4A; Design Decisions R-3.6C; Build Guide 3.6, 7.2; BOM 15.7). *Documents: as named.*

510. The other guides rewritten the way the Barometer guide was (Mike, 2026-11-02: "Please improve all other guide except main build guide, in the same manner as this one"). Done 2026-11-02. Every v10.4a master except the Build Guide, Start Here and the Barometer guide (done first, item 505) was rewritten for reading and building: what it is and "The idea" on top, one rules list, one parts table, a short why, build steps numbered and grouped by where and when, what can go wrong (what keeps the boat going), and the open items line; reference documents (Bill of Materials, Wire and Cable Buy List, System Settings Sheet, Glossary, Electronics and Compute Bay plans) kept their shape, IDs and rows, with plain section leads and history notes cut. Rules: _v104a_work/rewrite/REWRITE_RULES.md. No fact, number, part, price, link or never/must line was dropped: each guide passed _v104a_work/rewrite/check_facts.py against its copy from before (_v104a_work/rewrite/pre/). Long reasoning moved into Design Decisions (from _v104a_work/rewrite/to_DD/), which was rewritten last. Sections that moved are mapped in _v104a_work/rewrite/maps/, and 17 pointers between guides were fixed, plus 16 in this file. Printed pages went from 402 to 392 for the 21 documents besides Design Decisions: the gain is layout and plain words, since nearly every line is a fact. Each rewriter's report: _v104a_work/rewrite/reports/. Found errors are the next item; questions for Mike are item 512. *Documents: all of the v10.4a set except the Build Guide.*

508. The central node's box on hand is too small (Mike, 2026-11-02: "central node box is 12.9x9 ID. Will it fit? if not, should we get a bigger box or put it in 2 boxes"). No. The Central Node box plan's parts and three rails take about 14.4 x 10.5 in of plate, and its 15 bottom glands about 13.5 in of wall; the box on hand gives 12.9 x 9 in inside, about 30 percent less plate. Claude's pick: one bigger box, not two. Two boxes need a 20-plus core cable between them (relay coils, MOSFET gates, the expander's lines, power and 0 V), two more glands at each end and a second box to seal, all on the box that steers. Candidate: TICONN IP67 clear lid, 17.7 x 13.8 x 7.9 in, inside 16-7/8 x 12-7/8 x 7-1/2 in, grid mounting plate 15-7/8 x 11-3/4 x 1/8 in, two 304 latches, $94.99, in stock (Amazon B0BZR3M8PK; read from the listing's size chart by the VIADESKTOP session, 2026-11-02). The LeMotech (B0CQJNPGWN) and Zulkit (B0BPH1WQXD) of the same size are unavailable. DECIDED 2026-11-02 (Mike: "yes"): the TICONN B0BZR3M8PK is the central node's box; on the order tracker Buy list. The Central Node box plan is redrawn for it (layout to scale, parts page) and its wiring diagram is now two pages (5 pages in all). At the next write-in: Electronics plan A3 and Compute Bay 10.2 (the box). *Documents: Electronics plan A3; Compute Bay 10.2; the Central Node box plan; the order tracker.*

506. The barometer arm swings 10 degrees toward the bow, not 30 (Claude, 2026-11-02; Mike, 2026-11-02: "15 deg would improve function", then "10 deg is ok"). Done 2026-11-02. At 30 degrees the tube, which passes right through the 4 x 4 in post, ran into the corners and its port-face hole landed on the copper strap; at 15 degrees the port-face hole still reached the strap's forward edge (about 3 in back from the forward edge). At 10 degrees the tube shifts about 0.7 in aft crossing the post (4 in x tan 10) and each hole is about 1.52 in wide fore and aft; with the starboard hole centered about 1-1/8 in back from the forward edge, the port-face hole's aft edge sits about 2.6 in back, about 1/4 in or more clear of the 1 in strap, so the capped stub stays. The port now sits about 12-3/4 in out and 2-1/4 in forward, still 51-1/2 in up. Written into the Barometer guide sec 3 and both drawings, and Instrument Post Guide sec 11. *Documents: Barometer and Pressure Port sec 3; Instrument Post Guide sec 11.*

507. A drying tube on the barometer hose (Claude, 2026-11-02, from the Campbell manual; Mike, 2026-11-02: "yes dessiccant", then, on Campbell's quote-only kit, "That is not how/where i want to buy" and "better to just replace a cheap one at refit"). Done 2026-11-02. The BaroVUE 10 manual (rev 04/2022, pp. 12 and 16) requires a desiccant tube on the tubing from an outside pressure port. Bought part: the Drierite drying tube (W.A. Hammond 26930, the same tube Campbell's 39677 kit carries): 8 in long, 3/4 in across, 30 g of indicating beads (blue to pink), takes up 3 g of water, 20-micron filter each end, ports take 1/16 to 1/4 in ID tubing; Amazon B00PQZO988, 4-pack, $34.31 at the business price (read 2026-11-02). One goes in now, a new one at the Canaries refit, sooner if pink. Its ports take the 1/4 in hose and 1/8 in tubing directly, so the 1/4 to 1/8 in barb reducer is dropped; a short piece of 1/8 in ID silicone tubing (Amazon B0DSR9NDZ3, Rebower 1/8 x 1/4 in, 10 ft, $9.09) joins the tube to the sensor's barb. Not bought: Campbell's 39677 kit (quote only); the Amazon B0CCS3VR3M listing of the same tubes ($150.43, shipped from the UK in 6 to 7 months). How long one tube lasts is a guess: a long time, since the hose only breathes as pressure and temperature change. Written into the Barometer guide (rules, parts, sec 4, figure 1), Bill of Materials 15.11 (science balance now $934) and the order tracker (Buy list, Parts). *Documents: Barometer and Pressure Port sec 4; Bill of Materials 15.11; order tracker.*

505. The Barometer and Pressure Port guide rewritten to read and build from (Mike, 2026-11-02: "way to long and wordy ... make as useful as possible to review and understand the building process, making sure it meets our needs, and build from"). Done 2026-11-02: the guide went from about 3,800 words to about 2,200 and five pages, laid out as rules and parts, why, build steps, hose and wiring, what it can claim, what can go wrong. Two new drawings replace the v9.5 figure, which showed the arm on the port side and the old lightning rod: _v104a_work/media/Barometer_Port_v10_4a_fig1 and _fig2, drawn by _v104a_work/make_barometer_figures.py. Facts written in: from the Campbell manual (rev 04/2022, Reference/Campbell BaroVUE10 Manual 2022-04.pdf), the BaroVUE drifts about ±0.1 hPa a year, takes 1 s a reading, and mounts barb pointing straight down; this settles the BaroVUE data sheet item that was in Part 1B. The arm's load on the post figured at its real height (Claude's arithmetic): about 1,500 ft-lb added in the 19 kt crest case, post under 40 percent loaded; in the 19 kt rollover about 7,000 ft-lb against the 7,800 ft-lb the post holds corner-on. The pressure is read at the sensor's height, not the port's (the still air in the hose weighs the same as the air outside), so the height to record is the sensor's. Moved to Design Decisions R-10.2A: the arm material table and the post load numbers. Left out as settled or not this guide's: the RS-485 versus 0 to 5 V advice, the Young barometer's output rate, the 28.4 V bus figure (the guide now says only that the bus goes above 28 V), the terms table. Instrument Post Guide pointers to the old sec 3.5 now read sec 3. *Documents: Barometer and Pressure Port; Design Decisions R-10.2A; Instrument Post Guide secs 9 and 11.*

504. No box for Starlink (Mike, 2026-11-02: "no box for starlink"). The Starlink Mini sits bare on the aft deck, with no enclosure (it is IP67 with its cables plugged in). Its Ethernet takes a standard RJ45 plug, greased and taped with self-fusing tape (item 373); its power is the 16/2 from central node entry 5 to its DC input (how that joint is made is still open, item 353 (h)); what holds it down is still open (item 373). Done 2026-11-02: the Starlink Enclosure box plan is removed from Box_Plans_v10_4a, and the Central Node and Network Switch Box plans and the cross-check now end those two cables at the Mini. At the next write-in: Electronics plan A13 (no box: no entries, no glands) and sec 6.3; the Build Guide comms section ("a sealed enclosure"); BOM line "Starlink Mini + enclosure" (Mini only); Box_Wiring_Sheets_v10_4a page 40. *Documents: Electronics plan A13, 6.3; Build Guide comms; BOM; Box Wiring Sheets.*

503. The Archive folder is now Old, and every old subfolder sits in it (Mike, 2026-11-02: "please clean up claude boat folder, all the subfolders can sit inside an "old" folder", then "yes" to Claude's plan). Done 2026-11-02: Archive renamed Old; Backups, _backup_originals, v9_7e_Draft and the one file left in _v100_work moved into it; the eleven empty _v..._work shells removed (their contents were already in Archive); the five early wing boom drawings of 2026-10-27 and 28 and the Wing Can Spec Sheet of 2026-09-14, which no current guide points to, moved into it. The v10.3 and v10.4 files OneDrive put back at the top that morning (identical or older copies of what was already archived, checked file by file) are in Old/Put back by OneDrive 2026-11-02/. Five folders stay at the top: Box_Plans_v10_4a, Machine (the sync and the rules file; moving it breaks both), Old, Reference (the guides point to it by path) and _v104a_work. Dated drawings the current guides still point to stay at the top. The rules file's folder section, _v104a_work/promote.py, metrics.py and five guide masters (Start Here, Design Decisions, Wing Construction, BOM, System Settings) now say Old. At the next build: those five Word files pick up "Old" from their masters; read any Archive/ path in older items as Old/. At each promotion the superseded set and its work folder go into Old. *Documents: Start Here, Design Decisions, Wing Construction Guide, BOM, System Settings Sheet (Word files at the next build).*

499. Box plans v10.4a: one 4-page PDF per box (Mike, 2026-11-01: "please make (not redo, but make new ones) new plans for each box. 1 pdf per box"; then, on the long first version, "We want to be able to look at these to build a box, not read a book", "please keep the text black and at least 9 point", "yes, do all the boxes this way"). Made 2026-11-01 in the new top-level folder Box_Plans_v10_4a/ (files renamed 2026-11-02 to plain names that sort, Mike: "so they sort better (we are humans trying to use this)", for example Pi A Box v10.4a.pdf): sixteen plans, fifteen since the Starlink one was dropped (item 504) (Pi A, USB hub, Pi B, central node, BMS box, network switch box with the surge board, VESC A, battery box, backup battery board, Iridium A and B, detector, Release Node B, wing box, wet lab box) and Box Plans Cross Check v10.4a. Each plan is 4 pages: parts with photos, the layout, the wiring diagram, every wire. They add no decisions: each layout follows the box's earlier dated drawing or Box Wiring Sheet (Claude's layout, standing unless Mike says otherwise). Where a plan had to pick something no guide says, it is marked as Claude's pick or open on the page. The wet lab box's rail is 38 blocks with up to two wires to a screw in a double ferrule (the guides say about 30). Sources: _v104a_work/box_plans/four_page/ (the 4-page plans) and _v104a_work/box_plans/boxes/ (the full wire-by-wire data the cross-check reads). The old dated box drawings stay where they are. The rules file now says printed text is at least 9 pt and build sheets are short. At the next write-in: point Electronics plan Appendix A, the Box Wiring Sheets and Start Here to the plans. *Documents: Electronics plan Appendix A; Box Wiring Sheets; Start Here.*

486. Wiring review calls decided (Mike, 2026-10-31, answering item 482: "1. yes 2. yes 3. yes 4. yes 5. are you sure? if so, yes 6. yes, for sure! But make sure of this logic, it has been back and forth through the versions. 7. yes"). On (5), Claude's answer to "are you sure?": yes on the wiring, known from the text: after (a) to (d) every wire left in the aft junction only joins one cable to another; the one thing not known is whether the node box has room for two small converters, two fuses and the wind meter's Pololu, since the node is not laid out yet; if not, the two sealed converters (wire leads) sit on the hull beside the node. So all seven are decided. Written in 2026-11-01 (Mike: "Yes, update all guides, box diagrams, and make a special point to make sure all changes to main bus, solar, and other get done and not overlooked or forgotten") into every guide and drawing listed at the end of this item, the Word files and box sheet PDFs rebuilt, the order tracker brought up (aft junction row, YRDZXG, 30 A modules, fuse holders, Klnuoxj, 8-channel boards, the Do next list), Aft_Junction_Box_Build_Sheet_2026-10-30 moved to Archive; spec and reports: _v104_work/WRITEIN_2026-11-01.md, _v104_work/reports/W1_*.md. Close at the next open-list tidy. Two refinements made while writing it in: the post lights cable's drain goes to 0 V at the node only, and the failure list names a 1k failing open as the other thing that would stop charging (unlikely: it carries current only during a stop, at under half its 2 W rating). The decided design: (1) Bilge straight from the node (item 482 (a)): one C4 18/4 from the central node to both pumps, in node entry 9's spot (now a PG7): red pump 1 on, after channel 6's 5 A fuse; white pump 2 on, after channel 12's 5 A fuse; black pump 1 running and the 4th core pump 2 running, to opto inputs 1 and 2. Both running cores carry 24 V while their pump runs: colored heat shrink and labels P1 RUN and P2 RUN at both ends, never on a 0 V terminal. Shield trimmed and sleeved at both ends. Each switch-on still joins its pump's + after the Water Witch, no diode. The channel 6 16/2 run and the black wire re-marked red (item 467 (k)) go. (2) Whites without the light relay (482 (b)): channel 7's normally open contact, after its fuse at the node, feeds the whites' 12 V converter directly. The HiLetgo 30 A light relay, F3 and the relay's trigger jumper (item 485) go; three of the six 30 A modules are then spare. The fuse stays 0.5 A; 1 A if the converter's switch-on surge trips it. (3) Bow lantern fed from the node (482 (c)): from channel 3's contact through F4 (1 A) and the bow lantern's YRDZXG, both at the node, then its cable straight forward to the bow: a 12/2 offcut (about 80 ft of 12/2 is spare; a bigger wire is always allowed), sealant-filled gland, in node entry 7's spot (size the gland to the 12/2 jacket). (4) Light fuses at the node (482 (d)): F2 (stern light, 1 A) and F4 (bow lantern, 1 A) right after channel 3's normally closed contact, so nothing leaves the node on channel 3 unfused. (5) No aft junction box (482 (e)): the post lights cable, the post wind meter cable and encoder A's lead run straight to the central node, the way the horn pair already runs, through one Altelix 4-port split gland in node entry 17's spot (the trunk's), one port plugged. Post lights: a 22/12 offcut (round, 0.24 in; the lights draw milliamps), up the post as now: stern light + (24 V, after F2), whites + (12 V, from the whites' converter), 0 V, three cores each. Wind meter: its own Pololu D36V6F5 (Mike, 2026-10-30) and its 1 A fuse F1 move into the node, fed from the node's 24 V; its cable (22/12 offcut) runs straight up the post; data on D0 and D1 as now; the meter is now on only while the node's feed is on, which ends item 468 (e). Encoder A: its Belden lead straight from the rudder stock; its 3.3 V from the Nucleo as now (item 482 (k) still open). Wind data and light power stay in separate cables. The horn keeps its own 16 AWG pair (the horn-on-the-lights-cable option is dropped: the lights cable is 22 AWG). Inside the node: the two YRDZXG light converters, F1, F2, F4 and the Pololu. Goes: the aft junction box (the TICONN 12 x 8 x 5 in, free for another job), its five glands (two Altelix split glands back to the shelf), about 24 blocks, the surge diode on its input, the switch box's 24 V jumper and switch box entry 13, the channel 3 and channel 6 16/2 runs and the 12-core trunk (the C1 roll keeps its other jobs). Line 6 then feeds only the network switch box. Node gland count unchanged (21 and the vent): entry 7 the bow lantern, entry 9 the bilge, entry 17 the split gland. Ferrites on the post lights, wind meter and bow lantern cables move to the node. The C4 18/4 roll then carries the wing actuator run, the two puller runs and the short bilge cable, about 45 to 50 ft (guess); the UV-C run goes on a 22/12 offcut. (6) Charge stop as a pull-down (482 (f)): the 1k (one of the fifteen 1k 2 W resistors on hand; it carries about 29 mA, 0.8 W, during a stop) goes from the + 400 A bar straight to the yellow-wire strip, both on the main bus board, a few inches apart. One wire from the strip to the node, through channel 8's normally OPEN contact and a 0.5 A slow-blow fuse (DIN holder, kit) to 0 V. Coil on still means stop, so the software does not change. Logic, checked against Victron: on the non-inverting cable, the charger runs with the yellow wire above about 6 V (Victron's cable page; some SmartSolar manuals say 8 V) and stops below 1 V (2 V) or floating. Charging: the strip sits near bus voltage through the 1k. Stop: the contact closes and the strip sits at 0 V. A dead Pi, node, expander or I2C line, a reset, a broken wire, a loose screw, a dirty contact or a blown 0.5 A fuse all leave the strip high: charging. The old loop (+ through the 1k, out to the node, through the closed contact, back to the strip) stopped all five chargers on any break. The one fault left that stops charging is this wire rubbing through to minus, which every version with these cables has: sleeve it and keep it short. The 0.5 A fuse covers the wire rubbing onto a plus wire while a stop is held (the 1k covered that before). Five-day expiry and the Pi-silence drop stay in software as now. (7) No control CAN power (482 (o)): line 1 goes (its 5 A breaker, labelled CAN at the top of the board, its 16/2, one YRDZXG, the control power tee and its cut cordset); the 4-port tee's free end takes the terminator. Each control drop's black core lands on the HAT's G terminal and on the node's 0 V; the red core is cut back and taped at both ends. Why it is safe: the Waveshare HAT powers its own isolated CAN side (B0505LS-1W on its parts list), the node's CAN board runs off the Nucleo's 3.3 V and the VESC's CAN port takes no power. The house bus keeps its power (the em-trak's bus interface draws from it). At the write-in: Electronics plan 4.1, 5.2, 5.3, 6.4, 6.7, 7.1, 7.5, 7.6 (line 1 off, line 6 to the switch box only, the still-fused list), A1, A2, A3 (entries 7, 9, 17, contents), A6 (deleted, as A16), A6a (entry 13 off), A15 (house bus end unchanged); Compute Bay 10.2, 11; Build Guide 3.6, 4.1, 8.2A, 8.3; Battery Box Part 8 (the charge-stop wiring and its bench test); Instrument Post Guide 3 and 10 ("land every post cable at the aft junction" goes); Wire and Cable Buy List C1, C2, C4, C6, A9; Node Boxes Explained (figure 1 and sec 5); BOM 15.4, 15.7, 15.8; Box Wiring Sheets 0, A3, A6 (deleted), A6a, R1; Bilge Pump Wiring 2026-10-31 redrawn; Aft_Junction_Box_Build_Sheet_2026-10-30 to Archive; Reference/Main Bus Board Drawing 2026-10-06; the order tracker (aft junction rows, 30 A modules, fuse holders). *Documents: as listed.*

479. No holes on top of any box (Mike, 2026-10-31: "I think best for all boxes to avoid holes on top", then "yes"). Every box entry goes on a side or bottom wall, with a drip loop below it; nothing through a top wall or lid. Why: a cable coming down from the deck or the post carries any leak water straight into a top gland; on a side or bottom gland the drip loop sheds it. Already so for the network jacks, Pi A, Pi B and the wet lab box. Changes: the aft junction box's two post cables move to its right wall (done in the build sheet, item 467 (i)); the USB hub box's top-wall split gland S and PG7 T move to a side wall. Done 2026-10-31: the rule is in Electronics plan sec 7.1; the aft junction and the hub box (A1a, split gland S and the PG7 on side walls) are redrawn. Done 2026-10-31 for the central node too (item 481): Box Wiring Sheet A3's top-wall glands are moved to the side walls and Electronics plan A3 says so. *Documents: Electronics plan sec 7.1 (the rule), A1a, A3 and A6; Box Wiring Sheets A1a, A3 and A6; USB Hub Box Wiring 2026-10-20.*

481. Central node: no holes on top, entries numbered in order (Mike, 2026-10-31: "please make all adjustments to cent node box too"). Done the same day. The aft junction's two fixes, no holes on top (item 479) and gland numbers in order (item 467 (n)), now apply to the central node. The eight top-wall entries leave the top: the right wall takes the aft trunk, the horn pair and 1-wire chain 2 (17, 18 and 19, top to bottom); the left wall takes the wet lab line in, 1-wire chain 1 and the vent (20, 21 and the vent, the vent high); the bottom wall keeps its glands in the order drawn (1 to 16). Old to new: 2 to 1, 1 to 2, 12 to 3, 13 to 4, 16 to 5 to 9 (one number per run: 5 ch 1 Starlink, 6 ch 2 wet lab out, 7 ch 3 nav lights, 8 ch 4 em-trak, 9 ch 6 pumps on), 2a to 10, 3 to 11, 4 to 12, 4a to 13, 22 to 14, 27 to 15, 28 to 16, 14 to 17, 30 to 18, 17 to 19, 29 to 20, 18 to 21; 15, 20, 21 and 23 to 26 (not drilled, deleted or spares) get no number. Still 21 glands and the vent; no spare holes, and a new cable gets a new hole on a side or bottom wall and the next number, 22 on. What each cable carries does not change. Older Pending items and the Archive keep the old numbers. *Documents: Electronics plan box table, 4.1, 5.6, 6.1, 6.7, 7.1, 7.2, 7.5, A3 (table rewritten, a wall word on each row), A4, A6, A9, A10, A14, A16, A18 and the totals; Compute Bay Plan; Wire and Cable Buy List; Battery Box Building Guide; Transom Drogue Box Guide; Lightning Ground System Guide; Box Wiring Sheets (Sheet A3 redrawn with its notes and index row, and the central node numbers on Sheets A4, A6, A9, A10, A14, A16 and R1); BMS Box Wiring Diagram; Stern Release Wiring 2026-10-27; Backup Battery Board Layout 2026-10-15.*

485. Relay module trigger jumpers glued (Mike, 2026-10-31, after one came off: "Should jumpers be glued?"). Each HiLetgo relay module's trigger jumper (the small black cap on the 3-pin header marked L and H) is set, then held with a dab of removable silicone, the same as the harness plugs (Battery Box Building Guide Parts List and Part 8 (Inside the watchman box); Compute Bay sec 4 USB rule), so vibration cannot walk it off. A jumper that falls off leaves the relay's trigger undefined. The aft junction's light relay sits on high (middle pin and H), since its IN is tied to its own DC+; on low it would never pull in and the motoring whites would stay dark. Written into the aft junction build sheet step 3. Written into Electronics plan 4.1 (every HiLetgo module: the central node's, Release Node B's, the wet lab box's) and A18, 2026-11-01. The aft junction light relay does not exist (item 486). Left: one line in Box Wiring Sheet A3's notes. *Documents: Electronics plan sec 5.6, A3, A6, A18; Box Wiring Sheets A3, A6.*

467. Aft junction box build sheet: what drawing it found (Claude, 2026-10-30, from Mike's "make a layout for the aft junction box like you did for the others, with step by step"). At v10.4: (a), the F4 and F5 fuses on the two deck feeds, is written in. Still open: (d) to (h), Claude's standing calls (the post feed fuse kind and the others), each an Open line in the Electronics plan A6; Mike's yes or no settles each. Drawing: Aft_Junction_Box_Build_Sheet_2026-10-30 (.html master, .pdf to print, four pages: the plate lid off, the holes with the bottom wall seen from outside, every wire, notes and 21 build steps; built by Reference/_make_Aft_Junction_Box_Build_Sheet_2026-10-30.py). It keeps Sheet A6's walls and part places (post cables on the top wall, everything else on the bottom wall; feed terminals left, nav lights middle, relay top right, sensor terminals right). (a) DECIDED (Mike, 2026-10-30: "yes to fuses"): the two deck feeds get a fuse in the aft junction box, the bow lantern 1 A (F4) and Starlink power 5 A (F5), slow-blow, in DIN holders on rail 1; drawn into the build sheet the same day; the Electronics plan A6 and 7.6 "still fused" list and the order tracker's fuse holder count are still to write. The question was: fuse the two deck feeds that pass through unfused? The bow lantern (ch 3) and Starlink power (ch 1) leave this box with no fuse; a short on deck trips the central node's own 15 A breaker, which feeds the node and every relay channel, and because ch 3 fails on, a shorted bow lantern would trip it again each time it reset. Questions: (b) Entry 11 ("lights group") has no wire: the post lights cable (entry 4) carries the stern light and the whites, and the bow lantern has entry 19 (settles the "Lighting exits at the aft junction" fit-out flag if Mike agrees). (c) Entry 13 holds two cables to two places (em-trak, wet lab line), against the grouping rule (Electronics plan 7.2); Claude's view: the wet lab line takes entry 11. Claude's calls, standing unless Mike says otherwise: (d) the post feed fuses are DIN rail holders with 5 x 20 mm slow-blow fuses, 1 A each, three of them (wind, stern light, whites), since the post lights cable carries two feeds from two sources; the BOM 15.8 line said blade fuses and no holder was picked; (e) the motoring relay module runs off ch 7 itself (DC+ and IN on ch 7's red, trigger jumper high), so it draws nothing while off; (f) encoder A runs on the central node's 3.3 V sent up the trunk, so its pulse stays at 3.3 V for pin D6; trunk cores 1 and 2 wind data, 3 signal ground, 4 and 5 encoder, 6 and 7 the pump running states, 8 and 9 pump 2 on if it rides there, 10 to 12 spare; (g) no shield lands in the box; the trunk's drain goes to 0 V at the central node only, like the stern release cables; (h) the bottom wall's eleven glands (twelve with 15) go in two staggered rows, 1 in and 2-1/4 in below the rim, since one row needs about 12-1/2 in; that needs a base at least 3-1/2 in deep and a plate about 10 x 6 in (item 87). (i) Gland rework asked 2026-10-31 (Mike: "Need to rework the gland numbers, big OFI. Cutting holes just to be plugged, whose idea was that??" and "should we use 4x split for some to reduce holes?"). The plugged holes came from Electronics plan A6, which kept deleted entries (weather pod 5, shaft sensors 17) as plugged holes so the entry numbers would not move; the build sheet copied that. DECIDED (Mike, 2026-10-31: "yes"), drawn into the build sheet the same day, with the two post cables moved to the right wall (see item 479) and the bottom glands put in the order that keeps each cable under the blocks it lands on (3 the 24 V jumper; 4 runs ch 1 and ch 2; 5 Starlink; 6 wet lab; 7 runs ch 3 and ch 4; 8 em-trak; 9 runs ch 6 and ch 7; 10 the split gland, ports a trunk, b rudder sensor, c bilge leads, d bow lantern). Still to write: Electronics plan A6 (entry table and numbers), A3 entry 16 (two runs per gland, so three glands at the central node too), Box Wiring Sheet A6. The proposal was: number this box's glands 1 to 10 in wall order and drill only holes with a cable. Top wall: 1 post lights (PG7), 2 wind meter (PG7). Bottom wall: 3 the 24 V jumper (PG9); 4, 5, 6 the six 16/2 runs, two per PG13.5 (three oval jackets are about 0.6 in across, past a PG13.5's seal; a guess on the jacket size); 7 Starlink, 8 wet lab, 9 em-trak, each 14/2 in its own PG11 (ends the two-cables-in-entry-13 problem); 10 one Altelix PG25 4-port split gland (five-pack on hand, Amazon 113-9186532-4445843; 1-3/16 in hole, each port 0.15 to 0.30 in round cable) for the trunk (0.24 in), the rudder sensor lead (Belden, 0.175 in), the bilge leads and the bow lantern pair. That is 10 holes against 14 (15), no plugs; the bilge and bow lantern cables must then be round, 0.15 to 0.30 in. Old to new: 4 to 1, 3 to 2, 9 to 3, 10 to 4 to 6, 12 to 7, 13 to 8 and 9, 14, 16, 18 and 19 to 10; 5, 11, 15 and 17 dropped. (j) Bilge cable DECIDED (Mike, 2026-10-31: "18/4 should work fine"): one 18/4 shielded tinned cable (0.25 in, the C4 roll, the same one feeding the wing and the two quarter puller runs) from the aft junction's split gland port c to the two pumps, which sit together on the glass panel aft of the settee (Build Guide 3.6): red pump 1 on, white pump 2 on, black pump 1 running, 4th core pump 2 running; shield trimmed and sleeved both ends; drawn into the build sheet. (k) Pump 2's switch-on path from the central node (channel 12), asked 2026-10-31: the guides leave it to loom time, on two 22 AWG trunk cores or a seventh 16/2 run. DECIDED (Mike, 2026-10-31: "I think yes"), drawn into the build sheet: use the spare black wire of channel 6's 16/2 run (it has no job; it is taped at both ends today), re-marked red with heat shrink and labelled P2 ON at both ends. 16 AWG, behind channel 12's 5 A fuse, no new cable, no new gland, and no pump current in the sensor trunk; both pump switch-ons then share one cable, and the Water Witches still run both pumps if it is cut. The one cost: a black wire carrying plus breaks the usual color rule (black is minus), hence the red heat shrink and labels at both ends. At the central node it lands on channel 12's 5 A fuse; trunk cores 8 and 9 become spares. Still to write: Electronics plan 4.1 and A3 entry 16, A6, Compute Bay 11 (channel 12), Wire and Cable Buy List C2. (l) Is 18/4 big enough for the bilge cable? (Mike, 2026-10-31.) Yes: it carries only the shore switch-on current and the two running signals; each pump's working power comes on its own 16/2 from its 5 A breaker through its Water Witch. Switch-on current: Gulper 220 (pump 1) about 1.2 to 1.75 A at 24 V, Gulper 320 (pump 2) about 3.25 A, 4 A at most (Defender and Toplicht listings, read 2026-10-31), each behind a 5 A fuse at the central node; 18 AWG carries well over 5 A in a 4-core jacket, and a 10 ft run drops about 0.2 V at 3.25 A (inferred). Round tinned 16/4 marine cable (Pacer WR16/4, 0.42 in across) would not fit the split gland's 0.30 in port and is not sold on Amazon as far as found. Found in the same check: Whale recommends a 2.5 A fuse for the 24 V Gulper 220 (Defender listing and Whale catalogue), and 5 A for the 24 V Gulper 320; pump 1's breaker (line 11) and its channel 6 fuse are both 5 A. DECIDED: keep 5 A (Mike, 2026-10-31: "no to fuse change"); nothing changes. (m) Two split glands (Mike, 2026-10-31: "I think 2 4x glands to reduce holes with largest cables in the 4x"), drawn the same day: the two post cables share a second Altelix 4-port split gland on the right wall (gland 1: port a post lights, b wind meter, c and d blanked with the gland's own plugs), so 9 holes in all; the bottom glands renumber 2 to 9 (2 the 24 V jumper; 3, 6 and 8 the runs; 4 Starlink, 5 wet lab, 7 em-trak; 9 the bottom split gland, ports a trunk, b rudder sensor, c bilge, d bow lantern). The largest cables cannot go in a split gland: the 16/2 and 14/2 power cables are flat, and a split gland port is round (0.15 to 0.30 in), so it would not seal on them; they keep their own sealant-filled glands. The post lights cable must now be round, 0.15 to 0.30 in (the 18/4 on hand fits). (n) Gland numbers in order (Mike, 2026-10-31: "how about gland numbers in order?"): numbered in one walk round the box, along the bottom wall from corner 4 to corner 3 and then up the right wall: 1 the 24 V jumper; 2, 5 and 7 the runs; 3 Starlink, 4 wet lab, 6 em-trak; 8 the bottom split gland (a trunk, b rudder sensor, c bilge, d bow lantern); 9 the right-wall split gland (a post lights, b wind meter). Replaces the numbers in (i) and (m). (o) DECIDED 2026-10-31 (Mike: "yes, go with the simpler box, and make changes in all things that are related"). Simpler box, proposed after Mike's "use some sense on the glands and holes, this is getting silly". Starlink (ch 1), wet lab (ch 2) and em-trak (ch 4) only pass through this box: run each one's 16/2 straight from the central node to its load instead, with fuse F5 moving to the central node's rail; and the light relay's coil (ch 7, tens of milliamps) rides two spare trunk cores instead of its own 16/2. The box then takes 9 cables in 5 holes, all on the bottom wall in one row except the post cables: three PG9 (24 V in; ch 3 nav lights; ch 6 pump 1 on with pump 2 on on its black), the bottom split gland (trunk, rudder sensor, bilge 18/4, bow lantern), and the right-wall split gland (post lights, wind meter). It drops 6 terminal blocks, 6 cables through the box, 4 holes and the second row. Drawn in Aft_Junction_Box_Build_Sheet_2026-10-30 (5 holes: PG9 at 1-1/2, 2-3/4 and 4 in, split gland 4 at 6-1/4 in, all 1 in below the rim from corner 4; split gland 5 on the right wall 2 in from corner 2; rail 1 blocks 1 to 14 with F1 to F4, rail 2 blocks 1 to 10; trunk cores 8 and 9 the relay coil behind a new 0.5 A fuse at the node) and in Bilge Pump Wiring 2026-10-31 (bilge cable in split gland 4, port c). Still open as before: the post lights 4-core (item 440 (e)), the wind data line's surge part (item 440 (f)), and the bow lantern and encoder cables. *Documents: Electronics plan A6 and 7.6 (fuse kind and count, entries 11 and 13, trunk cores, encoder power); Box Wiring Sheet A6; BOM 15.8 aft junction line; order tracker (fuse holders) once answered.* (p) Light cables (Mike, 2026-10-31: "how about using cheaper 2-wire round cable"). The bow lantern cable (split gland 4, port d) is a round 2-wire cable, tinned, 0.15 to 0.30 in across, in place of the 18/4; the C4 18/4 roll is spoken for by the wing, the two puller runs and the bilge cable. Candidate B0DY7R46JG (18 AWG 2-core tinned shielded) dropped: $39.46 for 10 ft (Mike's screenshot, 2026-10-31: "too expensive"); cheap round 2-wire on Amazon is bare copper (the bare 18/4 went back for that reason) and tinned 2-wire is nearly all flat, which will not seal in a split port. Claude's pick: a second 50 ft roll of the same tinned 18/4 shielded (Amazon B0D9JV83HJ, $36.99 on 2026-09-21, about $0.74 a foot; 0.25 in, already proven in the split ports), for the post lights (one 4-core, as the guides already have it, so the post keeps five cables) and the bow lantern (two cores, the other two folded back); it also covers the C4 roll running short. DECIDED: no second roll (Mike, 2026-10-31: "no, don't think will need"). The post lights 4-core and the bow lantern cable come off the C4 tinned 18/4 roll on hand, with the wing, the two puller runs and the bilge cable; buy more only if the roll runs out at fit-out. Run lengths not measured; about 50 ft in all is a guess. *Documents: Electronics plan A6 entries 4 and 5 and sec 7.1 table; Wire and Cable Buy List C2/C3; Instrument Post Guide sec 10.1; build sheet pages 2, 3 and 5.*

Closed at v10.4a (written into the v10.4a guides, 2026-11-01)

Full text kept as it stood when written in. Item 494 was replaced by 496 (a) and was not written in. Item 492 (the single-point list) stays open in Part 1B; item 497's clashes left open are in item 498.

489. Rudder, wing and a bilge pump on the backup battery when the main battery is dead (Mike, 2026-11-01: "Need rudder and wing to work. And a bilge pump."). DECIDED 2026-11-01 (Mike: "Yes to this stuff", after the whole plan below): write it into the guides at the next write-in; parts on the order tracker Buy list 2026-11-01. Decided: when the main battery is dead or cut off, the rudder, the wing's trim actuator and a bilge pump must still work, from the Dyness (pump 2, always on the Dyness, below). Today they cannot: all three, and the central node that drives the rudder, run off the main bank (Electronics plan sec 7.6, lines 3, 5, 11 and 14), and the backup island powers only Pi B, WD-B, GPS B, Iridium B and the detector (Compute Bay 5.2). The way (Claude's, decided; it changes the main bus board and the backup battery board):

490. Charge stop deleted (Mike, 2026-11-01: "Yes delete", answering Claude's pros and cons). The five Victron VE.Direct non-inverting remote on/off cables (ASS030550320) are not fitted; they stay on the shelf. Gone with them: the yellow-wire strip and the 1k 2 W resistor on the main bus board, the run to the central node (A3 entry 14, not drilled), relay channel 8's charging role (the channel is spare), its 0.5 A fuse and DIN holder, the 5-day stop and its timer, the charging half of the node's Pi-silence timer (it still turns the nav lights on), and the RX pin "Remote on/off" setting (each charger's RX pin stays at its default). Why (Mike, 2026-11-01: "the risk of the victron cutoff cables failing and stopping the charging"): on a non-inverting cable a floating yellow wire stops its charger, so a loose or corroded plug or a broken yellow wire stops a charger, and the one shared 1k failing stopped all five, with nobody aboard to fix it; the stop was rarely needed (the route never gets cold enough; 27.6 V absorption leaves about 0.2 V a cell before overcharge). What is left: the five controllers' lithium profiles (27.6 V absorption, 27.0 V float) are the only charge ceiling; above 90 percent the Pi spends surplus on the prop (Build Guide 4.1), and shore can lower that ceiling to keep the pack off the top, for a high cell group or a cold or hot pack (inferred; not in storm or drogue states). The cold-pack (33 F) and hot-pack (131 F) alerts stay, now with no stop behind them. Nothing isolates the bank on the cell-temperature trip, as before (item 352 and 353 (d)). Docs to change at the next write-in: Battery Box Building Guide Part 8 and its charge-stop bench test; Build Guide 4.1 ("The charge stop is a pull-down", charging policy) and the power bench charging relay check (sec 11); Design Decisions R-4.1B and R-4.1E (rewrite as deleted, do not re-propose); Electronics plan secs 4.1 and 6.7, the central node fuse list and A3 entry 14; System Settings Sheet sec 1 (RX pin, charging relay, resistor and fuse, charging stop, Pi-silence timer) and the cold-pack row; Compute Bay sec 11 (channel 8 spare); BOM 15.4; Glossary; and any charge-stop lines in the Routing Guide, Transom Drogue Box Guide and Wire and Cable Buy List (found by search); the main bus board drawing, the central node sheet in Box_Wiring_Sheets_v10_4, Reference/BMS Box Wiring Diagram v10.4 and Node_Boxes_Explained_v10_4. Order tracker updated 2026-11-01.

491. The design rule: every backup keeps the mission going (Mike, 2026-11-01: "This was a HUGE oversight. We want all of the redundancies in the boat to be for the purpose to continue the mission."). Decided. Until now the failure rule was fail-safe only (Build Guide 5.1.1 and 8.2A: every protective default is where the hardware falls when its bus goes quiet), and the failure tables judge each row by safety (Wing Power System sec 9: "Losing the wing's electrics is never a safety failure: every row ends with a wing that can feather"). The rule now: every backup or second part exists to keep the mission going; when the main part fails, its backup must let the boat keep sailing toward the goal, not only keep it safe or call home. Parts with no backup (single points of failure) are a separate review, item 492 (Mike, 2026-11-01: "Rudder actuator (spof) is not what I'm talking about. I'm talking about redundant things purpose, which is to continue mission!"). Written into Machine/GLOBAL_CLAUDE.md 2026-11-01 so every session applies it. Docs to change at the next write-in: Build Guide 8.2A (beside the fail-safe rule) and 9.2 (failure handling); Design Decisions, a new R-entry; the failure tables (Wing Power System sec 9, Steering System Handbook sec 7, Compute Bay sec 11) get a "can it keep going?" column or line. The backups that fail it are item 493.

493. Backups that do not keep the mission going (Claude, 2026-11-01, under item 491). Fixes (1) and (2) DECIDED 2026-11-01 (Mike: "Yes to both software fixes"); (3) still open, in Part 2 (item 494). Each has a twin the boat cannot use while the main computer is alive. Work as meant: the five solar chargers, IMU A1 and A2, the post and wing-tip wind meters (for Pi A), VESC A's CAN and UART paths, Pi A's safe-mode copy, the two bilge pumps, and, since item 489, the backup battery and Pi B.

The fixes: (1) Pi A hands command to Pi B when Pi A loses a part Pi B has (GPS, Iridium or the hub): Pi A asks WD-A to drop the "main island alive" line, which wakes Pi B and puts it in command, sticky as now. Software only (Pi A, WD-A and Pi B), no parts. Pi B then steers over the control bus, trims the wing with its own adapter, and has GPS B, IMU B, Iridium B and the post wind meter; Pi A stays up as a helper and can pass Pi B its IMUs, wing sensors and Starlink over Ethernet while the switch works. Cost: Pi B awake, about 60 to 85 Wh a day from the Dyness, made up by running the Orion-Tr longer on relay channel 10. Fixes (a) and (b). (2) The em-trak as Pi A's second position source: the B921 is a Class B AIS transponder with its own GPS, on the house bus that Pi A reads (inferred that it sends its position on NMEA 2000); Pi A turns its relay channel on when GPS A fails. Software only. What Pi B takes from the hub box when it is in command (Mike, 2026-11-01: "How about the hub box? Can't pi b see it and run things from there?"): nothing directly. A USB hub answers to one computer at a time; the hub runs on the main side's power and ground, so a plain USB cable from Pi B would join the two sides (a USB isolator would work at full speed only and adds a part); and with the main side dead the hub has no power. Pi B gets what it needs elsewhere: the wing through its own adapter (item 489); wind from the post meter through the node (the primary reading); ships nearby from the em-trak, which also receives AIS and puts the targets on the house bus Pi B reads (inferred), so Pi B keeps the em-trak on while in command and the main side is alive. Lost while Pi B is in command: the wing-tip wind meter (the backup reading) and the wing compass (the wing still trims, damper off: Wing Power System sec 9); the science instruments and the hydrophone pause. Mike, 2026-11-01: "No to 2nd wing sensor"; not fitted, do not re-propose: a second Waveshare USB TO 2CH RS485 reader ($27.43 last time, Amazon B0D7BLNG75) in the Pi B box on the same two wing sensor lines, Pi B polling only when in command, with a cable into the Pi B box (entry 4 already carries the wing CAN). Docs to change at the write-in: Compute Bay 4.2 and 4.3 (the handover); System Settings Sheet sec 10 (handover triggers) and the GPS rows; Build Guide 8.3 ("both GPS lost") and 9.2; Electronics plan 5.4 (the em-trak as a position and AIS source).

494. The drogue on the backup battery alone (Claude, 2026-11-01; left over from item 493). REPLACED the same day by item 496 (a) (Mike: "1-2 yes"): this rested on a wrong number (a horn burns 12.5 A, not 25 A; Transom Drogue Box Guide sec 5). Do not write the way below in; it stays only as the record. Mike, 2026-11-01: "Backup drogue release burn should be powered from backup battery batt, I think." Claude agrees. DECIDED 2026-11-01 (Mike: "Yes to drogue"), the way below; it moves Release Node B off the house bus. Parts on the order tracker Buy list 2026-11-01. Today both release paths (horn A on the central node, horn B on Release Node B) run off the main side, and the backup converter's 17 A (item 489) is below their 25 A burn current (Electronics plan 7.6), so with the main side dead the drogue cannot be deployed. The way:

495. The cord pullers on the backup battery (Mike, 2026-11-01: "What about cord pulling"). DECIDED 2026-11-01 (Mike: "Yes"), the way below; it moves one more line onto the backup-fed bar. The four cord pullers (BRINGSMART 24 V worm motors that pull the T8 triggers to let the drogue go, on signed shore command only) run only through the central node, from release bus A (line 4), on the main side (Compute Bay sec 12; Transom Drogue Box Guide, "The pullers"). They fail to held: with the main side dead after a storm, the drogue could never be let go, so the boat could not sail on. The way: move line 4 (release bus A, 30 A breaker) from the branch bar onto the backup-fed bar of item 489, with the central node, steering and the wing box. With the main side dead, the backup converter then powers the pullers through the central node, and Pi B commands them over the control bus. A puller draws far less than the converter's 17 A (its stall current is not published; a guess of 1 to 3 A); four 64-second runs use about 2 Wh. Horn A's 25 A burn on the same feed still needs the main side (the converter limits at 17 A; Pi B fires horn B instead, item 494). The Argodiode's 80 A covers a main-side burn plus steering through the bar. No parts to buy. Docs to change at the write-in: Electronics plan 7.6 (line 4 to the backup-fed bar) and A3; Compute Bay sec 12; Transom Drogue Box Guide, "The pullers"; the main bus board drawing; and item 489's backup-fed bar list (now lines 2, 3, 4, 5 and 14, with item 496 (a)).

496. The backup review: decisions for Mike (Claude, 2026-11-01, from Mike's "Please do deep dive into eval and review of entire boat function with all backups in all combinations"). Full review: Reference/Backup Review 2026-11-01 (.md and .docx): every part one at a time, two failures at once, and fixes. Each needs Mike's answer:

497. Doc errors found by the backup review (Claude, 2026-11-01). Fix at the next write-in; nothing to decide. The list is in Reference/Backup Review 2026-11-01 sec 7 ("both GPS lost"; Routing 11.3 and 11.6, Compute Bay 5.2 and Wing Power System sec 9 calling Pi B a beacon or wingless; Build Guide 8.3 and 9.2 "routes through B"; failover 30 minutes against 90 seconds; fire both horns against fire B only on no confirm; System Settings Sheet sec 7's wind meter reader; Build Guide 4.1 and 4.2's below-5-percent line; charge-stop text item 490 missed; the 25 percent monthly exercise against the 30 percent cutoffs; no deploy command on the whitelist). Also the review's sec 8 seeds go to item 492.

Closed at v10.4 (written into the v10.4 guides, 2026-10-31)

v10.4 is the v10.3 set with these written in. Their full text is in Archive/Pending_Amendments_v10_4.md. Left over: item 478 (Part 1) and the "At v10.4" notes on items 442, 449, 450, 467 and 468.

Closed 2026-10-20 (written into the v10.3 guides)

441. The pad under the shaft thrust block is neoprene, not EPDM (Claude, 2026-10-20). The McMaster neoprene sheet that came 2026-10-20 (1290N252, 1/4 x 6 x 6 in, 50A, the last line of the 2026-08-18 order) is the pad under the thrust block: the thrust block parts list picked it (Reference/Thrust Bearing Selection 2026-08-11.md, item 4c), with the ribbed neoprene bushings and washers on the same order for its bolts. The guides had drifted to "EPDM pads". Neoprene stays: the block is packed with grease and sits in the bilge, and oil and grease swell EPDM, while neoprene stands them fairly well. Written into Build Guide 3.5, Design Decisions R-3.5C and BOM 15.5; the fastener list's washer line and the order tracker now say the washers and bushings are the thrust block's, not the motor bed bolts'. *Documents: Build Guide 3.5; Design Decisions R-3.5C; BOM 15.5; Reference/Fastener Inventory Bought 2026-10-03; order tracker.*

Closed by the v10.3 check (2026-10-19)

Nine reviewers read every v10.3 guide against the home guides, the order tracker and the decisions here; about 290 fixes went into the guides the same day. The main ones, so nobody re-opens them:

Closed at v10.3 (written into the v10.3 guides, 2026-10-19)

v10.3 is the v10.2a set with these written in. Left over: item 438.

Answered, do not ask again

548. Dated box sheets off the top (Mike, 2026-11-09: "Lots of box docs and other files that have dates, not 10.5 ver. Also many are repeating"; then "yes, go ahead"). Done 2026-11-09. Thirteen dated sheets that a box plan covers moved to Old/ (HTML and PDF): Backup Battery Board Layout 2026-10-15, Box Parts With Photos 2026-10-15, Cap Board Drawing 2026-10-14, Flipsky Hole Pattern 2026-10-26 (the full-size drilling template, kept there for Boat 2), Iridium to Pi Wiring 2026-10-15, Lightning Detector Wiring 2026-10-14, SDI12 Adapter Wiring 2026-10-21, USB Hub Box Wiring 2026-10-20, the three VESC A sheets (Build Prep 2026-10-24, Build Sheet 2026-10-26, Wiring 2026-10-14), Wet Lab Box Layout and Wet Lab Box Parts 2026-10-15. Every guide pointer now names the box plan. The three sheets that cover no single box stay at the top as PDFs, renamed Bilge Pump Wiring v10.5 (the BatteryProtect taken off it), Stern Release Wiring v10.5 (fire words changed to release) and Wing Boom Pocket Build v10.5; their HTML masters are in _v105_work/drawings/. This settles the bilge drawing's BatteryProtect in item 480.

547. Sync clash of 2026-11-09 7:25 am, settled (Claude, 2026-11-09). A session on VIADESKTOP renamed the order tracker while a cloud session renamed the v10.5 files, in the same hour. Thirteen files clashed: Start Here, Bill of Materials, Electronics and Wiring Plan, Wing Power System and Wire and Cable Buy List (Word files and their build copies in _v105_work/out), the rules file, and this file (markdown and Word). Both sides' changes are on main: the new file names and the new tracker name are in every master, this file and the rules file, and every Word file was rebuilt from its master afterward. Nothing was lost. Two words broken by the renames were fixed: the tracker's old name in item 542 and the rules file. The "(GitHub version 2026-11-09 7-25am)" copies and the notice live only in the OneDrive folder (the sync never puts them on GitHub) and can be deleted.

541. File names: spaces, not underscores (Mike, 2026-11-09: "can you remove underlines in all the 10.5 filenames?"). Done 2026-11-09: every v10.5 file and its master renamed (Build Guide v10.5.docx, 00 Start Here v10.5.docx, Box Wiring Sheets v10.5, Box Plans v10.5, Reference/BMS Box Wiring Diagram v10.5), every pointer in the guides and the rules file changed to match. The order tracker is renamed too (item 542). Then the rest of the top level (Mike: "yes, rename those too, i don't like underwhatevers"): this file (Pending Amendments v10.6), Team Progress Log.md and every dated drawing (Bilge Pump Wiring 2026-10-31 and the rest). Then Reference/ (Mike: "yes, rename the Reference files too"): 370 files and three folders renamed, every pointer changed; its scripts and the names that start with an underscore keep theirs. A script there that writes a file by its old name makes a new underscore copy if run again; rename the copy. *Documents: done.*

542. Order tracker renamed BOM v10.5 Order Status.xlsx (Mike, 2026-11-09: "Please update to 10.5, and get rid of underlines in filename"). Was BOM_v10_0_Order_Status.xlsx. Its Start here tab now says v10.5 (it said v10.4) and points to Old (it said Archive). The new name is in the rules file and the five guides that name the tracker (Start Here, Bill of Materials, Electronics and Wiring Plan, Wing Power System, Wire and Cable Buy List; masters and Word files). Dated reports in Reference keep the old name as written. Its history before the rename: git log --follow. Done.

539. Easy soldering stays (Mike, 2026-11-09: "Can solder easy stuff like pololu boards"). The no-fine-work rule (2026-11-08) means no desoldering and no tiny surface parts. Soldering a screw block or a few wires into through-hole pins or big solder cups stays: the screw blocks on the G2 drive and the Pololu regulators, the detector board's 8-way screw block and its two jumpers, the Neutrik plug on the S1eX, the two wires on each UV-C LED, and the one-time bench soldering rule (Electronics plan sec 4, Compute Bay 10.2). Claude's reading that all of these count as easy; Mike says if one is too fine. Nothing in the guides changes. *Documents: none.*