ViaBoat CAN

Boat 1 · GitBoat v10.5 · NMEA 2000 Micro-C

Click a solid box. Open is the panel button. Dashed grey = passive bus parts (tee / 120 Ω). Amber dash = off-bus 24 V. Electronics · Power · SOURCES.md

CONTROL Control bus end. Molded 120 ohm plug on the 4-port tee free port. The control bus carries no power. 120 Ω 4-port tee. Pi A and Pi B share this one tee. 4-port · Pi A · Pi B VESC A tee on the Control backbone. tee Central node end tee. Control bus end. end Control bus end. Molded 120 ohm plug on the central node end tee free port. 120 Ω Propulsion controller · GitBoat A7 · Boat 1 only. VESC A Nucleo G431 · releases · switched loads · steering drive. Central node bus end · 120 Ω on its tee Steering actuator · plain DC · not on CAN. Ewellix CAHB-22 off-bus 24 V Main compute island · GitBoat A1. Pi A both buses Floating backup island · GitBoat A2. Pi B both buses HOUSE House bus end. Molded 120 ohm plug on the power tee free port. 120 Ω Power tee. House bus end. 12 V from the sealed 24-to-12 V converter. Not a node. Power tee · 12 V 4-port tee. Pi A and Pi B share this one tee. 4-port · Pi A · Pi B em-trak tee on the House backbone. tee Wet lab box tee on the House backbone, ahead of Release Node B. tee Primelink A listen-only tap tee. Sec 5.2 does not name this tee. tee Release Node B end tee. House bus end. end House bus end. Molded 120 ohm plug on the Release Node B end tee free port. 120 Ω em-trak B921 Class B on the House NMEA 2000 bus. Purchased, not team-built. em-trak Wet lab box tee on the House backbone, ahead of Release Node B. Sec 5.2. Wet lab own tee Listen-only House tap. Sec 5.2 does not name this tee. Primelink A listen only House bus end. Its tee carries the terminator plug. Release Node B bus end · 120 Ω on tee WING · own short CAN link through the slip ring, never tees onto hull CAN · 120 Ω at each end of the link DSD TECH SH-C30G USB to CAN adapter in the hub box. Its 120 ohm switch is on. SH-C30G hub box · 120 Ω on Short J1939 on the slip ring. Not on hull buses. Wing box below deck · surge Wing trim actuator on its own short J1939 link through the slip ring. Electrak MD 120 Ω at the actuator slip ring USB to a hub port (Pending 443) unswitched 24 V PACK · context Main bank enclosure · GitBoat A9. Battery box Electrodacus SBMS0 · USB telemetry · not on CAN. BMS / SBMS0 USB · not CAN A16. Transom terminal box: none on Boat 1. The release cables run straight from the central node instead (A3 entries 11, 12 and 13; drawing Stern_Release_Wiring_2026-10-27). A16 none none No aft junction box. TSW202 is A6a. Aft junction A6 · no bus CANH CANL CAN drop off-bus 24 V Boat 2 only: VESC B and Electrak HD. Pi A and Pi B share one 4-port tee on each bus. 120 Ω plugs sit on the free port of each end tee (sec 5.1). Wing 24 V is unswitched.