Wing Power System: Build and Mounting Guide v10.5
v10.5, 2026-11-09. The wing's electrics. A sealed slip ring in the can, under the mast plate, carries eight wires across the wing's turning joint: up to the trim actuator in the boom-root pocket and the wind meter and compass at the wing tip, down to the wing box below the deck, where they enter the hull. The wing makes and stores no power, and nothing on it thinks. It runs from the hull's main bank; Pi A reads and drives it through isolated adapters in the USB hub box, and Pi B, in command, through its own adapter, without the tip meter or the compass (sec 8.7). The idea: strong wind feathers the wing with no power at all, so safety never depends on its electrics (sec 1). They need only be few, sealed and dry, with every ring wire guarded at the wing box so a strike on the mast stops there.
| Term | Plain meaning |
| Feather | Edge-on to the wind, making no force: the wing's safe state |
| Slip ring | Sliding contacts that pass wires across a turning joint |
| Fixed side, turning side | The ring's body stays still with the can; its flange end turns with the mast and wing |
| Hand-hole | The opening in the can wall that the ring is reached through |
| Boom-root pocket | The lidded pocket inside the wing, at the boom's root, that holds the actuator |
| CAN, RS-485 | Rugged two-wire data links: CAN for the actuator, RS-485 for the tip meter and the compass |
| Surge part | Does nothing at working voltage; shorts a spike across the pair it guards |
| Tail flap | The hinged back 2-3/4 in of the tail, the one surface the actuator moves |
| Give-way spring | The torsion spring between the horn and the tail flap. Past its setting, strong wind swings the flap toward straight whatever the actuator does (Trim Actuator Guide sec 6) |
| PEX | Plastic water pipe |
| DTM plug | A small sealed, crimped Deutsch 4-pin plug and socket |
| Butt splice | A crimped sleeve joining two wire ends, under glue-lined heat shrink |
Goes with: Build Guide secs 6.6 (the wing's electrics in short) and 3.3 (the can and slewing ring); Wing Can Spec Sheet; Rig Base Two Plate Design (ring bolts, fold); Wing Construction Guide; Wing Trim Actuator Installation Guide; Electronics and Wiring Plan A17 (the wing box) and A1a (the USB hub box); Lightning Ground System Guide secs 5 and 7.5. Prices and order status: Bill of Materials sec 15.6. Reasons: Design Decisions R-6.6B. The slip ring file: Reference/Wing Slip Ring Options 2026-09-24.md (secs 7, 9, 10 and 13).
1. Safe with no power, and the rules
Safety never depends on the wing's electrics. The give-way spring lets strong wind swing the flap straight whatever the actuator does, so feathering needs no power. There is no centering spring. With no power the flap holds its last trim, harmless in light wind; in strong wind the wing feathers, the boat loses its sail and shore is told. The load is small: the actuator, holding the tail flap against the air and a light 1/2 lb bias spring through its self-locking screw, plus the tip meter and the compass. It comes from the hull's main bank through the ring (sec 5), or, with the main side dead, from the backup battery through the backup converter (sec 6). Rules.
- On the wing, only the actuator and its cable, the tip meter and its 5 V converter, the compass and the wing cable. No battery, solar panel, panel pockets, lead channels or extra plies under pockets (Wing Construction Guide Stages 7 to 9), charge controller, charging link, radio, computer, watchdog, pod, potting or pod fuses: water and salt on bare boards kill the wing (Design Decisions R-6.6A).
- Never 24 V on either Calypso wind meter. They take 3.3 to 18 V and their clamping diodes conduct hard at 24 V: wired straight, a meter dies at first power-up.
- The compass takes 24 V (9 to 36 V), never the 5 V.
- The actuator's 24 V is never switched: the MD sleeps on its own after bus inactivity, under 2 mA.
- Every wire from the ring gets a fuse or a surge part at the wing box, so a strike on the mast stops there (sec 8.7).
- The actuator keeps its own CAN link, off the boat's two buses; the two Pis never both command it.
- No plugs at the slip ring; each wing cable is one piece from its butt splices below the mast plate to the actuator's DTM plug or the tip box, with no other joins (Mike, 2026-10-12 and 2026-10-31).
- No cable holes in the mast, in its wall or at the mast plate's center: the bore stays sealed by its weld.
- No soldering on the boat and no soldered field wires (sec 8.6).
- Each cable shield is grounded at one end only, never both: the hull end, or for the cable to the hub box, the wing box end (sec 8.7).
- No power or signal wire touches the lightning strap; only the surge clamps' common tail lands on its screw.
- A slit drip cup round the drive tube, never a boot clamped at both ends: the wing can wind up many turns one way over a voyage, and a boot would twist off.
- The compass on nylon or 316 screws, never plain steel, at least 4 in from the strike rod's base, the bird spikes and the 5 V converter.
1A. The slip ring and the wing compass
The ring sits in the can on the wing's turning axis, under the mast plate. It hangs by its turning flange from the foot of the drive tube, goes on at the bench and rides down with the mast lift, with nothing to line up; one stop bolt through the hand-hole keeps its body from turning (sec 8.5). A swap at a refit is the same job reversed through the hand-hole, with nothing lifted. Detail: Reference, Wing HC2549 and Compass Install 2026-10-01. [IMAGE] The drawing (Reference/Wing HC2549 Compass Install 2026-10-01.png, not to scale) shows the ring on its drive plate, the stop bolt and arm, and the compass at the tip. Where it differs from the text (the cable down the mast, plugs at the ring, a trailing-edge conduit, the drip cup hung from the bar), follow the text.
The ring
Rion HC2549-RZ086-P0410-S03-1C-IP65 (Rion's store is run by Moflon), built exactly as Rion drew it (Reference/Rion HC2549 Proposal Drawing 2026-09-30.pdf, 3D file beside it). Rion order 4524, due about 2026-10-20.
- 3.4 in (86 mm) across; about 4-1/8 in (105 mm) long, flange to tabs; the two tabs reach 4.8 in (122 mm) tip to tip.
- Turning end: a flange 3.4 in across, 5/32 in (4 mm) thick, with four slots 1/4 in (6.5 mm) wide on a 2.76 in (70 mm) circle. In its middle, a raised ring 1.57 in (40 mm) across; the turning-side leads come out inside it.
- Fixed end: two flat tabs, 5/32 in thick, each with an open slot 3/8 in (9.5 mm) wide; three cable glands off center on the end face.
- Four 10 A power rings on 16 AWG Teflon leads; a CAN pair and an RS-485 pair, each on its own shielded cable with its own shield ring. Leads about 10 in (250 mm) each side.
- IP65 (dust-tight and splash-proof, not for under water), aluminum, 0 to 60 rpm. Drag up to 35 in-lb (4.0 N-m), Rion's estimate of the twisting force to turn it.
The eight wires
| Ring | Wire | Carries |
| 1 and 2, 10 A | 24 V + and − | The actuator; and the tip branch, through its own 1 A fuse: the wing compass and the tip's 5 V converter |
| 3 and 4, 10 A | RS-485 A and B | The wing compass, on its own pair |
| 5, 6 and 7, shielded cable | RS-485 A and B, and shield | The tip wind meter. Ground the shield at the hull end only |
| 8, 9 and 10, shielded cable | CAN H and CAN L, and shield | The actuator (J1939), on its own CAN link. Ground the shield at the hull end only |
The wing compass
WitMotion HWT905, RS-485 version (also sold as RS-232 and CAN): a compass and gyro in an IP67 aluminum case, with a cable about 39 in (1 m) long; bought 2026-10-02. It needs 9 to 36 V and draws under 40 mA (WitMotion's HWT905-RS485 datasheet, sec 3.1). It speaks Modbus RTU (a simple ask-and-answer format) and answers only when asked. Its gyro gives the wing's turn rate for the rate damper; its heading minus the hull's gives the wing's angle against the hull to a few degrees (a guess), enough for the give-way check and for turning the tip wind into boat directions (Wing Trim Actuator Installation Guide, the rate damper). Open: its wire colors; its label settles them when it lands.
- Mount: a G10 pad, 1/4 in thick, about 3 x 2 in, glued on the tip cap at Wing Construction Stage 11; two nylon or 316 screws; arrow at the nose along the chord; at least 4 in from the strike rod's base, the bird spikes and the 5 V converter. Open: where the tip box and the compass pad sit on the tip; the tip mount drawing settles it.
- Wiring: the tip branch's 24 V after its 1 A fuse, ahead of the 5 V converter; its pair on rings 3 and 4; its joins in the tip box (sec 8.6).
- A strike that kills the tip meter will likely kill the compass too; the wing then trims without the damper until a refit (accepted, Mike, 2026-10-01).
The mount in the can
- Fixed side: a 316 post, welded to the center of plate 3 by the welder in the same visit that welds the can to plate 3 (size and height: Wing Can Spec Sheet). On it, a stop arm of 316 flat bar, 1/4 x 1 in, about 4 in long, running out from the center, with a slot 5/16 in wide and 1-1/2 in long across it, centered about 2-1/4 in from the post's center. The arm sits about 2-1/2 in below the ring's tabs, leaving the fixed-side cables room to drop and turn. The post also carries the lightning brush's bracket, a 316 flat bar screwed to its side (Wing Can Spec Sheet, "What attaches to the can"). Open: the stop arm on the can's build drawing.
- Stop bolt: 5/16-18 316, about 4 in long, through one tab's slot and the arm's slot, with a 316 spacer tube filling the gap, nylon washers on both faces of the tab and a nylock nut. The crossed slots take up any offset of the post.
- Turning side: a 316 drive bar hangs under the mast plate from two opposite inner-ring bolts of the bearing, so its middle is the turning axis with no measuring. Those two bolts are 1/2 in longer than the rest, about 5/8-11 x 3 in, still to buy (the bolt rules: Rig Base Two Plate Design, "Slewing ring bolts"). The 1 in 316 drive tube bolts under the bar's middle. Welded on its foot is the drive plate: 316, 1/4 in thick, 3-3/8 in round, with four 9/32 in holes on the ring's 2.76 in slot circle and a 1-3/4 in center hole that clears the raised ring and the leads, the tube's bore open through it. The ring's turning flange bolts under it with four 1/4-20 x 1 in 316 bolts and nylock nuts, a 1/16 in G10 gasket between to keep the ring's aluminum off the stainless.
- The bar and the tube are the brush's path (Mike, 2026-09-28): both 316, bolted metal to metal, so the path runs mast plate, the two longer inner-ring bolts, bar, tube, brush. Tef-Gel on the threads only; bare metal where the bar meets the bolt heads and the tube. The Helwig lightning brush rides sideways on the tube, below the bar and above the drip cup (Lightning Guide sec 5.2).
- Heights, down from the mast plate's underside: the drive bar; about 3 in of tube (the brush's zone, then the cup's top); the drive plate and gasket, about 5/16 in; the ring, about 4-1/8 in to its tabs; about 2-1/2 in to the stop arm. So the stop arm is about 10 to 11 in below the mast plate (an estimate; the can's build drawing settles it).
- The hand-holes: Wing Can Spec Sheet, "The hand-hole".
The cables
Turning side. The actuator cable, the wing cable and the bare 8 AWG lightning ground wire come down the wing's 1/2 in root PEX (sec 8.6): straight down through the wing root and the water-shedding disc, then through the PEX's own 3/4 in hole in the mast plate, about 5.1 in aft of the mast's center and about 1.4 in toward the pocket-lid face. The PEX ends inside the can about 3 in below the plate, its bottom end open so water drains out. The wing and the plate turn together, so nothing twists. The ground wire lands on the plate's underside (Lightning Ground System Guide sec 5.1).
- The two cables join the ring's turning-side leads with sealed glue-lined heat-shrink butt splices (22 to 16 AWG, on hand): the Cat6's 23 or 26 AWG ends folded double, each splice staggered along the bundle, a drip loop, the bundle tied to hang clear of the drip cup and the brush. They are made on the bench (sec 8.3) and sit about 13 in above the hand-hole's center.
- The cable tails are cut 2 ft long, so a refit cuts the splices and makes new ones.
- The tip's 24 V pair leaves the ring's 24 V pair here, at the splices.
- Open: how the two cables get from the root PEX's bottom end to the ring's turning-side leads (about 5 in sideways under the mast plate, the PEX ending about 3 in below the plate, above the ring's tabs); a drawn detail (detail E of Reference/Wing Lightning Wiring 2026-10-30) settles it.
- Open: how the ring's one 24 V pair feeds both the actuator cable and the wing cable at the butt splices; making up the joint settles it.
The mast plate's holes. The 3/4 in center hole is off the plate's cutting file (Reference/Mast Plate DXF Change Note 2026-10-31.md), but the 2026-10-13 cutting sheet PDF still shows it: tell the shop. Mike drills two holes at fitting, not on the cutting file: the 3/4 in PEX hole, marked with the plate held up under the finished wing root, and a #10 (13/64 in) hole about 1 in from it, away from the gussets, for the ground wire's bolt. Both clear the gussets, the ring bolt holes and the drip cup. Silicone round the PEX at its hole. Fixed side. The ring's three fixed-side cables each drop straight about 2 in, turn toward the can wall and plug into a hull cable (Deutsch DT), each with a drip loop. Each hull cable leaves the can by its own PG9 gland, low on the can wall on the side facing the deck gland (Wing Can Spec Sheet). The hull cables then go down through their own fixed watertight deck gland, clear of the plate, with a loop of slack at the tilt hinge, straight into the wing box. Open: the exact route from the can-wall glands to the deck gland; the can's build drawing and the wing box's hole schedule settle it.
Keeping the can's damp off the ring
The can is wet: salt air, condensation, and now and then a wash past the wing-root disc that leaves by the weep holes (Wing Can Spec Sheet).
- A drip cup: a plastic hat about 6 in across (so it passes the hand-hole), slit from its center hole to its edge, closed round the drive tube with a stainless hose clamp below the brush and above the ring; its skirt ends above the tabs (rule 12).
- Tef-Gel on every bolt (threads only on the drive bar's). The G10 gasket keeps the ring's aluminum off stainless.
- A corrosion blocker (Boeshield T-9 or CorrosionX) on the ring's outside and its bolts at fitting and at each refit, mainly where the turning end meets the body, where the seal rides.
- A drip loop at every cable entry, so water runs off the wire, not into the ring.
2. Every voltage and signal on the wing
| Rail | Where it comes from | What lives on it |
| 24 V | The hull's main bus to the wing box (line 14, on the backup-fed bar; its branch and breaker or fuse: Electronics and Wiring Plan A17 and sec 7.6), then the box's 5 A fuse and surge diode (sec 8.7), up across the ring's power rings 1 and 2 | The actuator: 0.6 A unloaded, 2.6 A at full load, under 2 mA asleep. The tip branch, through its own 1 A fuse: the wing compass (9 to 36 V, under 40 mA) and the tip's 5 V converter |
| 5 V, at the tip only | A sealed 24 to 5 V converter at the tip (sec 8.6) | The Calypso CMI1017 only |
| CAN | The actuator's own link: the ring's shielded CAN pair, a surge module in the wing box, the shielded cable to the isolated USB to CAN adapter on a port of the USB hub, and a third drop, joined at the wing box, to Pi B's own isolated adapter in the Pi B box (sec 8.7). A 120 ohm resistor across the pair at each end (at the actuator, and the hub box adapter's switch); Pi B's adapter has its switch off | The Electrak MD alone, off the boat's two buses |
| RS-485, tip meter | The ring's shielded RS-485 pair, then the shielded cable to the hub box's isolated 2-channel reader (sec 8.7). Its ground: the shared 24 V −, on the cable's ground pair | The CMI1017 alone |
| RS-485, compass | The ring's power rings 3 and 4, then the same cable to the reader's second channel; same ground | The HWT905 alone |
3. Parts
A blank status means Bill of Materials sec 15.6. Parts bought for the old wing power are on the order tracker's "Send back for refund" tab (BOM v10.5 Order Status.xlsx).
| Part | Status |
| On the wing | |
| Thomson Electrak MD actuator (MD24A025-0050CNO), about 2.4 lb (Trim Actuator Guide sec 2) | Trim Actuator Guide, Rules and parts |
| Actuator cable: tinned 18/4 shielded, 50 ft | Bought 2026-09-21: , $36.99 |
| Actuator plug: MUYI DTM 4-pin kit, 5 sets | , price not checked |
| DTM crimper: JRready, with 50 pairs of size 20 stamped contacts | , price not checked |
| Surge clamps: two 1.5KE33CA, a WAGO 221-415, heat-shrink butt splices | On hand |
| Surge clamps: two 1.5KE12CA two-way surge diodes | To buy: no Amazon listing found; , about $0.75 each |
| Wing cable: Mike's shielded Cat6 | On hand |
| Calypso CMI1017 tip wind meter, RS-485: the boat's backup wind reading and the post meter's cross-check, kept on purpose (Mike, 2026-09-26) | |
| WitMotion HWT905 compass, RS-485 version, and its G10 pad | Bought 2026-10-02 |
| Tip box and its glands; the sealed 1 A inline fuse; the DROK sealed 24 to 5 V converter | The converter is bought |
| Two 1/2 in PEX tubes, from one 10 ft stick; silicone | |
| In the can | |
| Rion HC2549 slip ring | Ordered: Rion order 4524, due about 2026-10-20 |
| Two longer 5/8-11 bearing bolts for the drive bar | To buy |
| Glue-lined heat-shrink butt splices, turning side | On hand |
| 316 drive bar, 1 in drive tube and drive plate, with the 1/16 in G10 gasket; 316 post (welded to plate 3 with the can) and stop arm; stop bolt, spacer tube, nylon washers, nylock nut; four 1/4-20 x 1 in 316 flange bolts with nylock nuts; three PG9 can-wall cable glands (Wing Can Spec Sheet); sealed Deutsch DT plugs, fixed side only; slit drip cup and hose clamp; #10-24 316 bolt and nut for the ground wire (Lightning Ground System Guide sec 5.1); Tef-Gel; Boeshield T-9 or CorrosionX | |
| The wing box | |
| TICONN IP67 ABS box, 5.9 x 5.9 x 3.5 in, with its mounting plate (), and its glands | Not yet bought |
| 5 A fuse on a short DIN rail; a 1.5KE33CA surge diode; three Taidacent RS-12V/2S surge modules, 12 V option () | |
| Shielded 4-pair cable to the USB hub box: Mike's Cat6, about 5 ft | On hand |
| The USB hub box and the Pi B box | |
| Hub box: one Waveshare USB TO 2CH RS485 isolated reader; one DSD TECH SH-C30G isolated USB to CAN adapter | Both bought 2026-10-07 |
| Pi B box: a second DSD TECH SH-C30G | To buy: |
4. Why it is built this way
- Nothing on the wing that a wet board can kill: water and salt on bare boards kill the wing, so the ring took every battery, panel, radio and board off it (Design Decisions R-6.6A and R-6.6B).
- The 24 V is not doubled: the actuator's 2.6 A peak is about a quarter of one ring's 10 A rating.
- The compass has its own pair, the two spare power rings: a fault on the tip meter's pair cannot silence it, and the tip meter keeps its plain wind format (NMEA 0183).
- The 5 V is made at the tip behind its own 1 A fuse, so a fault at the tip cannot blow the actuator's 5 A fuse.
- Butt splices, not plugs, at the ring: that joint should never need undoing; a refit makes new splices on the 2 ft tails.
- The cables come down a PEX tube, not down the mast: nothing twists, and the mast's bore stays sealed. A drained bore would drip down the drive tube onto the ring's turning end; water or condensation that collects inside is harmless in 2205.
- Isolated readers, and 115,200 baud: sec 8.7.
5. What the wing draws from the hull
Watt-hours a day (Wh) off the hull's main bank, carried over from the earlier wing budget.
| Draw | Wh a day | Basis |
| Actuator moving, full active trimming | 9.6 | 0.4 W average |
| Actuator asleep, its own controller | 1.2 | Under 2 mA at 24 V, published |
| Wind meter (Calypso CMI1017) and its tip regulator | Not known | The meter: 0.25 mA at 5 V, about 0.03 Wh a day. The tip regulator is the DROK sealed converter (sec 8.6), whose idle draw is not known; measure it at the bench |
| Wing compass | About 23 (planning figure) | WitMotion gives only a ceiling, under 40 mA at 24 V (HWT905-RS485 datasheet sec 3.1), and the plan carries it in full (Mike, 2026-10-12). A seller's 9 mA at 12 V would be about 5 Wh a day. 23 Wh is under 0.1 percent of the 32 kWh bank |
The adapters that read the wing and talk to the actuator (sec 8.7) run on Pi A's 5 V, and Pi B's CAN adapter on Pi B's, not on the wing's feed. The Waveshare reader's draw is not published (about 0.1 A at 5 V, a guess from typical chip figures); the CAN adapter's is not known. Measure the wing box's draw at first setup (sec 10) and put it in the hull load table (Build Guide sec 4.6).
6. Running low, and on the backup battery
The wing has no battery of its own. Trim and damping shed with the hull's load-shed ladder (System Settings Sheet sec 4); shedding either is safe (Trim Actuator Guide sec 8). On the backup battery. The wing box's feed (line 14) is on the backup-fed bar on the main bus board (Electronics and Wiring Plan sec 7.6). With the main side dead, Pi B turns on the backup converter and powers the wing box once an hour to check and trim the wing through its own adapter (sec 8.7), damper off. Just before the converter cuts off for low voltage (the boat then drifts), Pi B sets the flap straight once, since the wing box runs from the bar that converter feeds: the wing weathervanes and makes no push. The steer-or-drift switch and its energy budget: Compute Bay Plan sec 5.3.
6.1 When the wire goes quiet
The actuator is on a wire; there is no wing radio. If its CAN link goes quiet (the Pi hangs or is dark, the hull end fails, or a wire breaks), the MD stops and holds its last trim, and strong wind still swings the flap straight against the give-way spring and feathers the wing (Trim Actuator Guide sec 5). A quiet link needs no feather rule of its own.
7. Where everything sits on the wing
- The wing: its bottom edge about 21 in above the deck; it rises 6.5 ft; the root, the bottom 2 ft, wraps the mast top.
- The actuator: in the boom-root pocket on the wing's center line, rod line 47 in above the wing's bottom edge, under a screwed lid on the boom face (Wing Construction Guide; Wing Boom Pocket Build v10.5).
- The two PEX tubes: upright, 12 in back of the nose, beside the actuator: the root run from the pocket down into the can, the tip run from the pocket up to the tip (sec 8.6).
- At the tip: the wind meter on a short arm ahead of the nose, with its converter and the tip box (sec 8.6), and the compass on its pad on the tip cap (sec 1A). The wing cable reaches them up both PEX runs.
- In the can: the slip ring, under the mast plate (sec 1A). Nothing runs inside the mast.
- Below the deck: the wing box, where the wing's wires enter the hull (sec 8.7).
- The lightning strap: copper, outside the skin on the face without the pocket lid, from the 15-1/2 in strike rod at the tip down the spar line to a bolt on a mast-base gusset. Its two landing screws, 45 and 46 in up, take the actuator jumper, the boom wire and the ground wire (Lightning Guide sec 5.1).
- The nose locker: lead only (Wing Construction Guide Stage 10).
8. Building and mounting it, step by step
Work in the order of 8.1 to 8.5; then the wing box (8.7) and the checks (sec 10).
8.1 Order first
- Order the mast weldment with no cable holes (rule 8; Wing Construction Guide Stage 4). Tell the shop the 2026-10-13 cutting sheet's center hole is gone. Mike drills the PEX hole and the ground wire's #10 hole at fitting (sec 1A).
- Get the can welded with its hand-hole and the slip ring post (Wing Can Spec Sheet). The welder welds the post to the center of plate 3 in the same visit, so settle its size and height and the brush bracket before the can goes.
- Set up the compass on the bench (sec 8.5).
8.2 While the wing is built (Wing Construction Guide)
- Glue in the two 1/2 in PEX tubes when the boom-root pocket is built, and prove their pull strings (sec 8.6).
- Before the root PEX is glued in, pull the actuator cable, the wing cable and the bare 8 AWG ground wire into it with the pull string, and the wing cable on up the tip PEX. Nothing can be added to a sealed wing later.
- Wire the tip box: the 1 A fuse, then the compass and the tip converter, both on the 24 V after the fuse. Connect the meter only after reading 5 V at the meter's end of the converter's lead (sec 10).
- The actuator's DTM plug and its surge clamps go in the pocket (sec 8.6); the compass on the tip cap (sec 8.5).
8.3 On the bench, mast upside down
- Bolt the 316 drive bar under two opposite bearing bolts, the two longer ones, bare metal under the heads.
- Bolt the drive tube, drive plate end down, under the bar's middle, bare metal to metal, Tef-Gel on the threads only.
- The root PEX passes through its own 3/4 in hole in the mast plate, drilled at fitting (sec 1A); silicone round it. The two cables and the ground wire hang out of its open end.
- Butt-splice the two cables to the ring's turning-side leads: staggered, on 2 ft tails, with a drip loop, the bundle tied to hang clear of the drip cup and the brush (sec 1A).
- Lay the G10 gasket on the drive plate and bolt the ring's turning flange to it with the four 1/4 in bolts, Tef-Gel on the threads. The ring now hangs from the tube; its body turns freely by hand.
- Coil the fixed-side leads and tape them to the body. Wrap the ring in cardboard or a towel for the lift.
8.4 In the can, then the lift
- Fit the stop arm on the post at plate 3's center, and the brush bracket.
- Bring the hull cables in through the three can-wall glands, each ending in its DT plug.
- Lift the mast on as already planned (Rig Base Two Plate Design). Lower it slowly at the end, so the ring clears the post and the stop arm. Nothing has to engage.
8.5 Fitting the slip ring and the wing compass
Through the hand-hole, last, with the mast on and the ring hanging from the drive tube. The lightning brush first, so its sanding grit is cleaned out before the ring is unwrapped:
- Fit the Helwig brush on its bracket on the post, pressing sideways on the drive tube below the bar.
- Wrap sandpaper round the tube, grit out, and turn the wing by hand so the tube wears the brush's face to its curve. Take the sandpaper off and clean the tube. No grease where the brush rides.
- The brush's spring force is not known: check the tube and drive plate do not move under its push.
- Meter mast to can: under 0.1 ohm (Lightning Guide sec 8.1).
Then the ring:
- Take off the wrap. Turn the ring's body by hand until one tab's slot sits over the stop arm's slot.
- Put the stop bolt down through both slots: nylon washer, tab, nylon washer, spacer tube, arm, nut. Snug the nut. Nothing is forced: the ring already sits where the drive tube put it, and the crossed slots take up any offset of the post.
- Untape the fixed-side leads. Let them drop straight about 2 in before they turn toward the gland, then plug each into its hull cable, with a drip loop in each.
- Wipe the corrosion blocker on the ring's outside, mainly where the turning end meets the body, and on the bolts.
- Hang the drip cup round the tube by its slit and tighten the hose clamp.
- Put the ground wire's ring under the nut of its #10-24 316 bolt on the mast plate's underside (Lightning Ground System Guide sec 5.1).
- Bolt the hand-hole cover on.
To swap the ring at a refit: the same steps backward through the hand-hole: four bolts overhead at the drive plate, the stop bolt and three plugs, and new butt splices on the cables' 2 ft tails. Nothing is lifted; the ring never needs the mast off. The wing compass.
- On the bench: power it from 24 V and connect it to a PC through a USB to RS-485 adapter, with WitMotion's free software. Leave its address as it comes (it is alone on its pair). Set its speed to 115,200 baud (it comes set to 9600; System Settings Sheet sec 8): a poll for turn rate and heading then takes about 2.3 ms on the wire, against about 28 ms at 9600. Check the heading follows as you turn it by hand. Read its label for its wire colors.
- At the tip, at Stage 11 or at fit-out: glue the pad on the tip cap, square to the mast with the boat upright, so the compass sits level, at least 4 in from the strike rod's base, the bird spikes and the 5 V converter; leave the spikes off that patch. Screw the compass on, arrow to the nose along the chord. Run its cable into the tip box through a gland, with a drip loop. Splice its power and ground to the tip branch's 24 V after the 1 A fuse, ahead of the converter (never to the converter's 5 V output), and its A and B to the wing cable's compass pair (crimped heat-shrink splices, no solder).
- On the boat, on the hard or in calm water: the magnet calibration and the angle table (sec 10).
8.6 Wiring and keeping water out
- Wire and joints: all wire on the wing is marine tinned. No soldering on the boat and no soldered field wires (Electronics and Wiring Plan sec 4): every joint is a crimp under glue-lined heat shrink, a lever connector, a screw terminal or a sealed crimped plug, with a service loop (a little slack) at every wire end. A board's terminal blocks may be soldered on once at the workbench, before it is installed. Every wire exit is through a gland, a PEX mouth or potted.
- The actuator run: the tinned 18/4 shielded cable, 0.26 in across, from its butt splices below the mast plate up the root PEX to the DTM plug in the pocket. It carries the 24 V pair, and the CAN pair with a 120 ohm resistor across it at the actuator end only; the link's other end is the CAN adapter's switch in the hub box (sec 8.7). The shield crosses the ring on the CAN cable's own shield ring and is grounded at the hull end only. At the wing end it is left unconnected (Mike, 2026-10-12): trimmed back at the plug harness and sleeved, touching nothing. The run in the pocket: Trim Actuator Guide sec 4 Step 4.
- The actuator's plug: one Deutsch DTM 4-pin pair, DTM04-4P and DTM06-4S with wedgelocks, size 20 stamped contacts (they take 16 to 22 AWG; the 18/4 fits). The Thomson comes with bare wires. The plug sits in the pocket above the motor, wherever the lead reaches, greased and booted. One pair is used, at the actuator only.
- The two PEX tubes (Wing Construction Guide, the PEX tubes): 1/2 in PEX (0.625 in outside, about 0.485 in inside), upright, 12 in back of the nose beside the actuator, each with a pull string; one 10 ft stick covers both. The root run goes from the pocket's bottom wall (its end 1/2 in above the pocket floor) straight down through the wing root, the water-shedding disc and the mast plate (sec 1A). It carries the actuator cable, the wing cable, the bare 8 AWG ground wire and the pull string, all pulled in before it is glued; both its ends stay open. The tip run goes from the pocket's top wall up to the tip closeout, carries the wing cable alone, and is sealed at its tip end. The fit is tight, and accepted (Mike, 2026-10-29).
- The tip's feed: the wing cable carries a 24 V pair, branched off the ring's 24 V pair at the butt splices, and the tip meter's and the compass's RS-485 pairs, up both PEX runs. In a small sealed tip box the 24 V pair goes through its own sealed inline 1 A fuse, then feeds the compass straight and the DROK sealed 24 to 5 V converter bought for this job (Bill of Materials sec 15.6), which makes the 5 V for the tip meter only. Open: where the tip box sits in the tip mount; the tip mount drawing settles it.
- The wing cable: Mike's shielded Cat6 on hand, all copper, 0.225 in across, about 8 ft with its loops from the tip to the root, plus the run on down the root PEX to its splices. Open: whether its conductors are stranded or solid (stranded was asked for); a look at the cable on hand settles it.
- Breathing: the nose locker has a small waterproof breather. The boom-root pocket has none: its two floor drains and the lid's corner notch let it breathe.
Surge clamps at the actuator, in the pocket at the DTM plug, so a strike that lifts the actuator's case lifts its wires with it (drawn on Reference/Actuator Surge Clamps 2026-10-31):
- A 4 in pigtail butt-spliced (heat-shrink butt splices, on hand) onto each of the actuator's four wires, about 3 in from the plug.
- 24 V+ and 24 V- each through a 1.5KE33CA (on hand) to a common; CAN H and CAN L each through a 1.5KE12CA two-way surge diode (two to buy) to the same common.
- The four diode legs and a 6 in 12 AWG tail in one WAGO 221-415 lever connector; the tail ends in a #10 ring on landing screw 2, with the ground wire (Lightning Ground System Guide sec 5.1).
- The 120 ohm terminator across CAN H and CAN L there (left out if Thomson's manual says the MD has one inside).
- Each part in heat shrink, the bundle tied to the motor shelf; crimped, no solder.
- Open: the sheet's details (the diode values, the 12 AWG tail to the ground wire's screw, the terminator at the actuator) have no yes from Mike; his read of the sheet settles them.
8.7 The wing box
The hull end of the slip ring: a small box below the deck, where the wing's wires enter the hull and the ring's eight wires land. Every wire from the ring gets a fuse or a surge part at this box's entries, so a strike on the mast stops here and does not reach the other boxes.
| Ring wires | At the wing box entry |
| 24 V pair | The 5 A fuse that feeds the actuator (slip ring file sec 12), then a 1.5KE33CA surge diode across the pair. The diode starts to conduct at 31.4 V, above the bus's charge ceiling; it works both ways, so there is no polarity to get wrong |
| CAN pair | A Taidacent RS-12V/2S DIN-rail surge module, the 12 V option (Amazon B0BGL675ND), then the shielded cable to the hub box. Each module's ground terminal goes to the box's 24 V negative terminal, as the battery bus surge modules' do, so the boat keeps its one bond wire |
| Tip meter's RS-485 pair | A second Taidacent RS-12V/2S, then the shielded cable to the hub box |
| Compass's RS-485 pair | A third Taidacent RS-12V/2S, then the shielded cable to the hub box |
A shorted surge diode (rare) blows the 5 A fuse: the wing loses trim, and the hull is never shorted.
- The box: the TICONN IP67 ABS box, 5.9 x 5.9 x 3.5 in, with its mounting plate (Amazon B0B87VR84G), holding the three surge modules, the surge diode and the 5 A fuse on a short DIN rail. They fit, with about 0.4 in to spare on the plate and about 1/4 in under the lid (inferred; Electronics and Wiring Plan A17). Not yet bought. No vent (Electronics and Wiring Plan sec 3). Six glands, all on the bottom wall: four PG9 (the 24 V in and the three hull cables) and two PG7 (the Cat6 to the hub box, and Pi B's CAN drop). Open: each hull cable, so its gland size; picking the hull cables settles it (Electronics and Wiring Plan A17).
- Its 24 V feed from the bus: Electronics and Wiring Plan A17 and sec 7.6.
The cable to the hub box. Nothing in the wing box thinks. One shielded cable, Mike's Cat6 on hand (a 4-pair shielded cable fits), runs about 5 ft from the wing box to the USB hub box beside Pi A (Electronics and Wiring Plan A1a; both boxes sit in the middle of the boat), with one gland at each end. Its pairs (Wire and Cable Buy List C8): blue, the actuator's CAN; orange, the tip meter's RS-485; green, the compass's RS-485; brown, ground, tied to the wing's 24 V negative in the wing box. The ground pair is needed because an isolated adapter's signal side floats: it must share a reference with the sensors, or the signals drift out of range.
- It is 23 AWG, so most likely solid: strap it within a few inches of each box so it cannot flex at the terminals, and put the wires in bare, no ferrule.
- Its shield is grounded at the wing box end only (Mike's OK, 2026-10-09): twist the braid or drain into a short pigtail, sleeve it, and land it on the box's 24 V negative terminal with the brown pair and the three surge modules' ground terminals. At the hub box, trim it flush and sleeve it, touching nothing. Never both ends, never the hub end only: the strike comes in at the wing box, so the shield drains there and does not carry a surge into the box beside Pi A (Electronics and Wiring Plan A17).
- At the hub box it enters by one of the box's three glands and lands straight on the Waveshare reader's screw terminals (Electronics and Wiring Plan A1a); the wing Cat6 measures 0.225 in across (Mike, 2026-10-29). Open: which gland it takes, and Mike's word on its landing; a look at the box settles it.
In the hub box (Mike, 2026-10-07):
- The tip meter and the compass: one Waveshare USB TO 2CH RS485 (SKU 27646), an isolated 2-channel USB to RS-485 reader with FTDI chips, clipped on a rail and plugged into one port of the USB hub. RS-485 terminators off: at 115,200 baud the run is far too short for echoes on the line to matter.
- The actuator: one DSD TECH SH-C30G isolated USB to CAN adapter (Linux sees it as a standard CAN port), plugged into a port of the USB hub (Mike, 2026-10-20), so the wing's control depends on the hub, as the wing's two readers do. Its 120 ohm switch on; the actuator end has the other. Both channels of Pi A's CAN HAT carry the boat's two buses, so the actuator needs a CAN port of its own.
In the Pi B box: a second DSD TECH SH-C30G isolated USB to CAN adapter (Amazon B0CDGGBZDT), a third drop on the actuator's CAN link, in by the Pi B box's entry 4 (Electronics and Wiring Plan A2); both channels of Pi B's HAT carry the two buses too. It joins the link at the wing box: its CAN pair lands with the Cat6's blue pair under the CAN surge module's OUT screws, two wires in one ferrule, and its ground on a spare ground block; it enters the wing box by its own PG7 (Electronics and Wiring Plan A17). Its 120 ohm switch is off, since its run is a branch; the hub box adapter's stays on. Pi B uses it only when it has command; the two Pis never both command the actuator. Pi B's USB then carries Iridium B's isolator and this adapter. Pi B has no wing sensor reader: with Pi B in command the wing trims by the post wind meter (read by the central node), IMU B and GPS B, damper off. Not wanted, do not re-propose: a second wing sensor reader for Pi B (Mike, 2026-11-01). Why isolated: for a split second a strike on the mast can put the wing box's ground far from Pi A's. Over plain copper that would drive current down the ground wire into the hub and Pi A; an isolated adapter has no copper across its gap, so the surge stops at an inexpensive part (Lightning Guide sec 7.5). Timing. The rate damper needs the wing's turn rate under 100 ms old (Wing Trim Actuator Installation Guide, the rate damper):
- the compass runs at 115,200 baud (set up in sec 8.5), polled 20 times a second for turn rate and heading;
- the tip meter sends its wind sentences once a second; the program finds its speed at start-up by trying the standard rates;
- a device rule on Pi A sets each FTDI chip's USB latency timer (how long it holds a part-filled message before sending) to 1 ms;
- the wing program runs on Pi A as its own high-priority process;
- every reading carries the time it was taken, and the damper skips any over 100 ms old.
A reading is then about 5 ms old when the command goes out. Settings: System Settings Sheet secs 8 and 9. Detail: Reference, Wing RS-485 Readers and Timing 2026-10-07.
8.8 The wing's program and its watchdogs
There is no wing computer. The wing's program runs on the hull's Pi A (or on Pi B when it has command), under the hull's watchdogs (Compute Bay Plan sec 4.3). Pi A's safe mode runs the wing trim too.
9. What happens when things fail
Losing the wing's electrics is never a safety failure: every row ends with a wing that can feather. Every backup is also there to keep the mission going (Mike, 2026-11-01; the rule: Build Guide sec 8.2A), so the last column says whether the boat keeps sailing.
| If this fails | What happens | Why it is OK | Keeps sailing? |
| A ring contact, or the ring (about 3 to 5 in 100 over two years, a guess) | No trim (a 24 V or CAN ring), no tip wind (the meter's RS-485 ring) or no compass (ring 3 or 4) | The flap holds; strong wind feathers the wing against the give-way spring | A meter or compass ring: yes, the wing still trims. A 24 V or CAN ring: only on the last trim, until a refit |
| A surge part fails shorted | The 24 V diode blows its 5 A fuse; a shorted module takes its pair down | The hull is never shorted | As the ring row, for the pair lost |
| The trim wiring or the actuator | No active trim | The flap holds; strong wind feathers the wing | Only on the last trim, until a refit |
| The CAN link goes quiet (the Pi hangs or is dark) | The MD stops and holds its last trim | The give-way spring is still the fuse; the Pi's watchdog restarts it (Compute Bay Plan sec 4.3) | Yes, once the Pi restarts or the other Pi takes command |
| Pi B in command (Pi A down or handed over) | Pi B trims through its own adapter (sec 8.7), damper off, by the post wind meter, IMU B and GPS B; no tip meter or compass | The flap holds between moves; strong wind feathers the wing | Yes |
| The main side dead, on the backup battery | Pi B powers the wing box once an hour to check and trim; just before the converter cuts off, the flap is set straight once (sec 6) | Strong wind still feathers the wing | Yes while the backup converter runs; in drift the wing weathervanes with no push |
| A fault at the tip | Its 1 A fuse blows: no tip wind reading | The actuator keeps its power; the post meter is the primary | Yes |
| The compass goes quiet | The software marks the wing angle stale and turns the damper off | The wing still trims; the give-way spring still lets it swing into the wind | Yes |
| Hull power to the wing box | No trim, no tip wind | The flap holds; strong wind feathers the wing | Only on the last trim |
| A direct lightning hit | May kill the actuator, the tip meter, the compass or the ring | The wing box's entries stop it, and the isolated adapters in the hub box stop what gets past; a dead wing costs trim, not the boat | A dead meter or compass: yes. A dead actuator or ring: only on the last trim |
10. Checks (part of the Build Guide sec 11 campaigns)
Bench, the tip supply. With 24 V on the meter cable's power pair and the meter not yet connected, read 5 V at the meter's end. Only then connect the meter. Bench, fail-safe. The proof test of the Trim Actuator Guide sec 7 (Test 1), on the bench and again on the boat: rod locked at full extension, power off; pulled toward straight with a hanging scale at the flap's back edge, the flap swings toward straight against the give-way spring and springs back when let go. Open: Test 1's pass band with the give-way spring at the flap (about 1.45 lbf at the flap's back edge to start and about 2.0 lbf at full give, worked out from the spring's 4.0 and 5.6 in-lb over the 2.75 in flap, inferred); a worked check written into the Trim Actuator Guide settles it. There is no centering spring, so there is no return test. Not a test: cutting power and expecting the flap to spring straight. With a self-locking actuator it cannot pass and proves nothing. Bench, the quiet wire. Stop the CAN messages: the MD stops and holds its last trim, and resumes when they come back. Never a latch-off. On the boat.
- With hull power on, turn the wing slowly through its full swing: the actuator answers and the tip meter and the compass read at every angle, so all eight wires are continuous.
- Calibrate the compass once, on the hard or in calm water: start WitMotion's magnetic calibration over its RS-485 pair, turn the wing slowly by hand through two full turns, then stop it. The strike rod, spikes, actuator and mast turn with the wing, so their pull calibrates out.
- The angle table: paint marks every 30 degrees on the mast plate and the can lip, turn the wing to each, and save the compass heading minus the hull heading. The 12 numbers become the hull software's wing angle table (setting: System Settings Sheet sec 8).
- Record what the wing box draws with the wing resting and while the actuator trims, and add the figures to the hull load table (Build Guide sec 4.6).
On the water and in the storm tests. After the closure checks and the high-wind buffet run (Build Guide sec 11.2): inspect the pocket's two floor drains, the lid notch, the PEX mouths and the tip mount, and confirm the wing still feathers and trims.
11. Open items
Open questions for this guide are in Pending Amendments v10.6.