The wing tab spring link: what it is

inchesOct 29, 2026 · proposed, not decided · page 1 of 2

What it does: it sits between the actuator and the pushrod. Up to 4 lb it is a solid stick, so the actuator steers the tail flap. Past 4 lb the spring gives and lets the flap swing toward straight, so a stuck actuator can never hold the wing pulling hard in a gale (Trim Guide sec 6).

Where it sits (not to scale)

sparactuatorspring linkboom: the link rides in its 1 in CPVC tube, the pushrod in its PEX linertail flapfront pinnut

The link cut in half, full size (print at 100 percent), actuator fully in

1front of cap A: the tongue, 0.22 in thick, in the actuator's fork1cap A (shop-made, one piece with the tongue)2tube, 5/8 in7lock ring: holds cap B where it is set8cap B (shop-made): screw in or out to set the 4 lb10coupling nut: joins rod and pushrodactuator's front end; its forkgoes over the tongue (dashed)10 mm front pin, ring-grooved3washer W15pin C1 through the rod4spring, squeezed to 4 lb3washer W25pin C29O-ring: keeps the grease in6rod, 1/4 in11pushrod, to the flap12CPVC tube, 1 inboom's front end

How it gives

1. At rest: rigid

Normal sailing. Each washer rests on its cap's face, with a pin through the rod right against it. The spring already pushes 4 lb on both washers, so less than 4 lb on the rod moves nothing: the link is a solid stick.

2. Pulled back hardrod

The flap pulls harder than 4 lb. Pin C1 drags washer W1 back and squeezes the spring. Cap B holds W2. The rod slides back, the flap swings toward straight, the wing turns edge-on. Pin C2 moves into cap B's pocket.

3. Pushed forward hardrod

Or pushes harder than 4 lb. The mirror image: pin C2 drags W2 forward, cap A holds W1, and pin C1 and the rod's end move into cap A's pocket. When the wind eases, the spring pushes everything back. Nothing to reset.

The wing tab spring link: the parts

inchesOct 29, 2026 · proposed, not decided · page 2 of 2

Numbers match page 1. Three parts are made by a machine shop, all three from one short piece of 7/8 in 316 round bar: cap A with its tongue, cap B, and the lock ring. Everything else is bought. Nothing on the list is bought yet except the rod.

PartSize and what it doesHow manyWhere to buy
1Cap A, with its tongueMade by a machine shop (sizes below). 316, 0.84 in round.1From 7/8 in 316 round bar, about 6 in does all three shop parts: Speedy Metals 7/8 in 316 bar, cut to length, price not checked. Or the shop's own.
2Tube5/8 in across, 0.049 in wall, 316. Cut to suit the spring (about 1-1/2 in) and threaded 5/8-18 outside at both ends.1Amazon, VALVENTO 12 in, 2 pack, price not checked.
3Washers W1 and W20.265 in hole, 0.50 in across (no wider: they slide inside the tube), 1/16 in thick. Size AN960C416. 18-8 stainless: no 316 found this size.2Aircraft Spruce, $0.21 each, or McMaster 98017A660, 100 for $15.92.
4SpringAbout 1/2 in across, 0.041 in wire, about 4 lb per inch, 2 to 2-1/2 in long free.1Closest found: Penn Tool 03308525: 0.48 in across, 2 in long, 4.2 lb/in, fully squeezed 0.47 in; stainless, probably 302, not the 17-7 PH the Trim Guide asks for; pack of 10, $13.65. No 17-7 PH spring this size found in stock.
5Pins C1 and C21/16 in by 3/8 in 316 dowel pin, pressed into a 1/16 in hole drilled across the rod.2Olander 1/16 x 3/8 in 316 dowel pin, price not checked. (A bought shaft collar is 1/2 in across: too wide.)
6Rod1/4 in 316, about 4 in, threaded 1/4-28 at the back.1On hand: cut from one of the two 24 in MECCANIXITY rods (Amazon B0DRJ1JWDM).
7Lock ringA 5/8-18 316 jam nut, turned round to 0.84 in by the shop.1Amazon, Aspen 15 pack or McMaster 94805A231, 5 pack, prices not checked.
8Cap BMade by the machine shop (sizes below).1Same bar as cap A.
9O-ringSize 010: 1/4 in inside, 3/8 in outside, 1/16 in thick, Viton.1Amazon, 10 pack, price not checked.
10Coupling nut1/4-28, 316, round, 0.36 in across, 1 in long. Joins the link's rod to the pushrod.1McMaster 93282A160, price not checked. Amazon has it only in 18-8.
11Pushrod1/4 in 316, about 47 in, threaded 1/4-28 at both ends.1Needs one 48 in piece; the rod on hand is two 24 in pieces. No 48 in 316 rod found on Amazon yet.
12CPVC tube in the boom1 in CPVC hot-water pipe, copper tube size: 1.125 in outside, about 0.92 in inside. 9-1/2 in used.1Home Depot, Charlotte Pipe 1 in x 10 ft, $19.51. Not on Amazon.
GreaseMarine grease, fills the tube round the spring.On hand. If not: Amazon, Sta-Lube 3184.
Actuator pins10 mm stainless, ring grooves. The front one must be under about 1.2 in long overall to fit the boom's 1-1/4 in bore.2Rear: McMaster 93890A742, 18-8, rings included. Front: none found short enough yet. I don't know if Thomson includes pins.
Clevis at the flap1/4-28, 316, with its 1/4 in pin and cotter pin.1McMaster 6071K47, price not checked. Its pin is 1/4 in, so the flap's arm gets a 1/4 in hole.
Thread diesOnly if you thread the tube and rods yourself; the shop can do it.5/8-18: Amazon, uxcell tap and die set (China-based seller). 1/4-28: Amazon, tap and die set. Prices not checked.

The three shop parts (316 stainless, 0.84 in round)

Why these sizes