Pushrod to the Thomson: the G10 tab with the 2 in gap

inchesOct 30, 2026 · full size: print at 100 percent

What it is: the Thomson's front end is a fork made for a flat plate. The pushrod's clevis (the U-shaped end screwed onto the rod) holds a flat G10 tab (its own pin plus a 10-32 screw). The tab goes into the Thomson's fork on its one 10 mm pin. Between the two metal ends is 2 in of bare G10.

Looking along the pins (the tab's flat face)

Thomson front end2 in of bare G10: the lightning gap-5/1602-3/43-3/84-3/4in behind the Thomson's pin110 mm pin (Thomson's)3clevis's own 1/4 in pin410-32 screw and nyloc5clevis, McMaster 6071K476pushrod2flat tab, 1/4 in G10, 3/4 in wide (green)

From above (the tab on edge)

2 in of bare G10: the lightning gapfront 1 in sanded to 0.21 inThomson front end: 0.87 in round, slot 0.236 in110 mm pin, ring clips: McMaster 93890A741, ends cut short3clevis pin and cotter, come with it410-32 screw and nyloc nut5clevis, 5/8 in6pushrod

The numbers, all measured back from the center of the Thomson's 10 mm pin

WhatWhere
Tab's front end5/16 in ahead of the 10 mm pin
Thomson fork's tips0.45 in behind (Thomson catalog)
Clevis's jaw tips2-1/2 in behind: the 2 in gap is between these two
Clevis's 1/4 in pinabout 2-3/4 in behind
10-32 screw5/8 in behind the clevis pin, about 3-3/8 in
Tab's back end5/16 in behind the screw; the tab is 4 in long
Clevis's back end (pushrod starts)2 in behind the clevis pin, about 4-3/4 in

The G10 tab: make it, fit it, keep it clean

inchesNov 2, 2026

Make the tab

  1. Cut 1/4 in G10 (on hand) to 3/4 x 4 in. Stick the template (below) on.
  2. Drill 10 mm (25/64 in) on the front cross. Round the front end around the hole.
  3. Sand the front 1 in to 0.21 in thick, both faces. One thin coat of epoxy. It should slide into the fork (0.236 in) with a little play.
  4. Slide the back end into the clevis. Jaw tips 2-1/2 in behind the 10 mm hole. Drill 1/4 in through the clevis pin hole.
  5. Clevis pin in. Drill 3/16 in through clevis and tab, 5/8 in behind it. 10-32 x 1 in screw and nyloc. No glue.
  6. Pin head to one side, cotter legs flat. File the clevis corners if it rubs in the tube.
  7. Round the corners. Wipe with acetone.

Fit it

  1. On the bench: pushrod into the boom's front, back end first.
  2. Lid off. Run the actuator to its retract limit. Line the tab's 10 mm hole up with the fork.
  3. 10 mm pin in with Tef-Gel. Ring clips on both ends.
  4. Look: 2 in from the clevis jaw to the fork tips, nothing metal between.
  5. Back to mid-stroke: flap straight.

Keep the gap clean

  • Nothing across the 2 in: no wire, screw, tape, paint or grease.
  • At each refit, wipe it. Burnt or cracked? Make a new tab.

Why

  • G10: keeps the pushrod's metal off the actuator's. A strike down the pushrod must jump 2 in; the wire outside the boom is the easier path.
  • Second fastener (the screw) stops the tab swinging in the clevis.
  • Strong enough: the actuator pushes 56 lb at most; the tab holds about 2,000 lb (worked out).

Parts

  • 1/4 in G10 (on hand).
  • Clevis McMaster 6071K47, with its pin and cotter.
  • 10-32 x 1 in 316 screw and nyloc.
  • 10 mm pin 93890A741, ends cut to 1/16 in past the grooves.
sand to 0.21 in10 mm: drill here1/4 in: about here; mark it from the clevis (step 4)10-32: drill through the clevis (step 5)this bar prints 1 in longFULL-SIZE TEMPLATE: print at 100 percent, cut out, stick it on the G10 blank, drill the 10 mm hole on the cross