Wing from the Aluminum Plate Up

Wing from the Aluminum Plate Up

Prime Ranger's wing rig, everything above plate 1. Drawn to scale from the v10.3 guides, 2026-10-26.

wing 78 in tall (6.5 ft) nose to back edge 27.7 in can 21 in pivot axis, 6.93 in back from the nose. The whole wing spins here box spar, 4 x 3 in, the spine; 8.31 in back wire tube, then 1 in of solid glass Lightning rod: 1/4 x 3/4 instainless bar, thin edge intothe wind, 12 in above the tip Wind meter on its arm(backup wind reading) Tip box: the meter's 5 Vconverter and its 1 A fuse Copper strap, 1 in wide, glueddown the spar line (the strikepath); a 2 in lap near the root Skin: 3 layers of glass clotheach side, 6 at the nose; whitepaint. No carbon anywhere 104 foam ribs, one every 3/4 in,cut by machine to the airfoilshape and stacked on the spar Glass socket, 26 in deep: themast is glued in, plus two 3/8 inthrough-bolts (9 and 18 in up) Nose locker, lead bars in arack (up to 24 lb). Lid on top,vent, two drains, 6 bolts intothe solid core. Nothing electric Root closeout: breatherand a weep hole, so theshell can dry out Water-shedding disc, about28 in across; its skirt dropsinside the can's turned-up edge Mast plate, 15-1/4 in, 3/4 inthick, 6 gussets; strap boltsto a gusset hole 12 main bolts, 3/4 in: headswelded under the deck, twobronze nuts each on top Plate 1: 36 x 36 x 1/2 inALUMINUM, glassed to thedeck. It keeps the water out Tip cap: bird spikes and thewing compass on its pad G10 block, 5 in, in the spar top:the rod and meter arm bolt to it Fixed tail, 27 x 11 in.It weathervanes the wing Pushrod along the boom to thetab horn; the spring link in it isthe wind-load fuse (a galepushes the tab straight) Actuator in its sealed fairingat the boom root, 47 in up; theboom bolts through solid glass Breakaway link (snaps at abird strike, saves the tail) Trim tab: the back 2-3/4 in on3 pin hinges, the only movingpart. A light spring centers it Wire tube inside the back edge:actuator and tip wires, root toactuator to tip. Last 1 in of theedge is solid glass Wires cross the root into themast bore (hole spot still open) Mast: 3-1/2 in heavy-wallstainless pipe, about 3-3/8 inshowing. The fuse: it bends first Turning bearing, 20.4 in: innerring turns, outer bolts to the lip Can lip: 3/4 in stainless ring,20-3/4 in, 16 gussets under it Drive tube from the mast plateturns the slip ring; thelightning brush rubs on it Slip ring: 8 wires cross theturning joint; stop bolt to the post Hand-hole, 7 x 9 in (one oftwo), to reach the slip ring Fixed-side wires leave low on thecan wall, down their own deck gland Plate 3: 24 x 24 x 1/2 in stainless.12 gussets at the can base; rearhinges so the rig folds back
Side view, cut open to show the inside parts: spar, ribs, socket, wire tube, actuator and pushrod, the lead rack in the locker, and the slip ring and drive tube inside the can. The copper line is the lightning strap. Heights of the bearing stack are drawn close, not exact.

3D view

Drag to spin the view. Scroll or pinch to zoom.
wing, boom, tail (fiberglass) stainless (plates, mast, rod) aluminum plate 1 painted steel can turning bearing copper lightning strap

What you are looking at

From the bottom up: plate 1 (36 in aluminum, glassed to the deck, the watertight layer), plate 3 (24 in stainless, nutted onto the 12 main bolts, with the fold hinges at its back edge), the can (16 in painted steel tube, 21 in tall, slip ring inside, hand-holes to reach it), the bearing on the can's lip, the mast plate and mast (3-1/2 in heavy-wall stainless pipe, glued and bolted into the wing's socket), and the wing: 6.5 ft tall, 27.7 in deep, foam ribs under a fiberglass skin. The boom carries the fixed tail; the trim tab on the tail's back edge is the only moving part. The nose locker holds the lead that balances it. At the tip: the wind meter, the wing compass, bird spikes and the lightning rod, whose copper strap runs down the outside of the skin to a gusset at the mast base. Everything above the bearing turns together; the "turn the wing" slider shows what moves and what stays.