Lightning on the wing: every wire, and nothing else

inchesNov 2, 2026
1tip rod (in the guides)2copper strap down the wing's far face (in the guides)3jumper: actuator's rear pin to the strap4ground wire inside the cables' PEX, to the mast plate5boom wire: tail to the strap6the 2 in G10 gap: NO wire8bolted splice9landing screws on the strap10gusset bolt at the mast base (in the guides)11PEX through the mast plate; ground wire to its undersideSeen from the wing's far face (the face without the pocket lid). Rough scale: about 1/15 full size.

Outside: tip rod, wing strap, boom wire. Inside: only the jumper and the ground wire. All outside copper goes on the wing's far face, so the pocket lid still comes off.

What, made ofFrom, toHow
1Tip rod
1/4 x 3/4 in 304 bar (bought)
wing tip to the strapAs the guides (Lightning Guide 5.1 step 2).
2Wing strap
1 x 1/16 in copper bar (bought)
rod base to gusset bolt at the mast baseAs the guides, on the far face. Two landing screws set under it (detail B).
3Jumper
6 AWG tinned wire, about 6 in (on hand)
actuator's rear pin to landing screw 2Out a 5/16 in hole in the far skin (details B, C).
4Ground wire
bare solid 8 AWG (Home Depot)
landing screw 2 to mast plate's undersideIn a 1/4 in hole, then inside the root PEX with the cables, all the way down (details B, E).
5Boom wire
6 AWG tinned wire, about 5 ft (on hand)
tail's rear clamp bolt to landing screw 1Along the boom's far side, splice at the root, then the far face at 44-1/2 in up (details A, D).
6The gap
2 in of bare G10
pushrod's front clevis to actuator's front forkNo wire, ever.

Not used: braid sleeve, braid jumper, hose clamp, any wire across the gap, a taller tip rod, a wire on the pushrod.

Lightning on the wing: how to build each wire

inchesNov 2, 2026

Build it, in order

  1. PEX (pocket step 3): pull the 8 AWG ground wire into the 1/2 in root PEX with both cables, before gluing. 2 ft spare at the root end, 1 ft in the pocket.
  2. Holes (after the doublers): 5/16 in and 1/4 in through the far skin, about 11 in back, 46 in up, 1/2 in apart, small one aft. Jumper out the big one, ground wire out the small one. Glue-lined heat shrink where each passes; 5200 in both holes.
  3. Strap (Lightning Guide 5.1 step 3), far face. First set two #10 silicon bronze screws through it from behind at 45 and 46 in up, heads glued so they can't spin: the landing screws.
  4. Jumper: 6 AWG lug on the rear pin's far end, ring clip over it. Out the hole; #10 lug on landing screw 2.
  5. Ground wire, top: 8 AWG #10 ring lug on landing screw 2, over the jumper. The surge clamps' tail lands here too.
  6. Ground wire, bottom: the root PEX runs down through its 3/4 in mast plate hole and ends open in the can. The wire comes out its end, up to an 8 AWG #10 ring lug on a #10-24 316 bolt through the plate. Bare metal.
  7. Boom wire (Stage 12, boom on): 1/4 in lug under the tail's rear clamp bolt head, far side. Forward along the boom's upper half, above the pushrod tube, in glue-lined heat shrink, glass strips every 4 in, faired. Off the boom just behind the wing's back edge, down to the splice.
  8. Face run: 6 AWG from the splice forward on the far face at 44-1/2 in up, 1/2 in clear of the drain holes, to a #10 lug on landing screw 1.
  9. Splice: lugs tongue to tongue, 1/4-20 316 bolt and nyloc, self-amalgamating tape.
  10. Every joint: No-Ox-Id between faces; 5200 over outside joints. Then the guide's continuity checks (sec 8).

Rules

  • Nothing across the G10 tab's 2 in gap.
  • No lug under the 4 boom root bolts.
  • Undo the splice before the boom comes off.

Why each one

  • Strap: takes a tip strike down the outside.
  • Jumper: ties the actuator's case to the strap.
  • Ground wire: in a strike the case jumps thousands of volts. The ground wire makes the actuator's wires jump with it, so no spark goes through its control board.
  • Boom wire: a tail strike takes the copper, not the pushrod.
  • Gap: a strike would have to jump 2 in to reach the actuator.

Parts

  • 6 AWG tinned wire, about 7 ft (on hand).
  • To buy: bare solid 8 AWG copper, 8 ft (Home Depot); two 8 AWG ring lugs for #10 studs.
  • 6 AWG lugs on hand: 1/4 in (3 used), #10 (2), 3/8 in (1).
  • Two #10 silicon bronze screws and nuts.
  • 1/4-20 316 bolt and nyloc (splice); #10-24 316 bolt, nut, washers (mast plate).
  • No-Ox-Id, 5200, glue-lined heat shrink, self-amalgamating tape.

Lightning on the wing: details A and B

not to scaleNov 2, 2026

A. The tail end, seen from the far side

1boom wire, upper half of the boom2its lug under the rear clamp bolt's head4bare jam nut: no wire on the pushrod5clevis on the horn

The boom wire ends under the tail's rear clamp bolt (the boom's end, dashed, is inside the tail's slot behind the clamp plate). No wire on the pushrod.

B. The landing on the wing strap, far face

1wing strap (copper), far face2screw 2: jumper and ground wire3screw 1: boom wire45/16 in hole: jumper51/4 in hole: ground wire6from the splice

About B

  • The two landing screws are set under the strap when it is glued: #10 silicon bronze, low heads behind the strap, at 45 and 46 in up.
  • The two holes (5/16 and 1/4 in) are about 3 in behind the strap, through the pocket's far wall, 1/2 in apart, each filled with 5200.
  • Screw 2 takes the jumper's lug, then the ground wire's 8 AWG ring. Screw 1 takes the boom wire's face run.
  • No-Ox-Id between every face; a nut on each; 5200 over the lot.

Lightning on the wing: details C, D and E

not to scaleNov 2, 2026

C. The actuator's rear pin, from above

far skin1rear pin, 10 mm2jumper's lug, far end3ring clip over it4actuator's rear fork5out through the far skin

The rear pin must be long enough for the fork plus the lug: 26 mm or more between its ring grooves (McMaster 93890A742).

D. The splice at the boom root

1from the boom2to the strap31/4-20 316 bolt, nyloc nut4lugs tongue to tongue, No-Ox-Id

On the wing's far face just ahead of its back edge, below the boom, at 44-1/2 in up. Undo it before sliding the boom out.

E. The PEX through the mast plate

water-shedding discmast plate1#10 bolt, ring under its nut2PEX through the plate, sealed3cables on to the slip ring4ground wire to the plate

The PEX goes straight down through its own 3/4 in hole, about 5.1 in behind the mast's center. The plate turns with the wing, so nothing twists.