Boom-root pocket: what to cut, glass and G10

boom face of the wing · inchesNov 2, 2026
cut the foam out (red stripes)biax glassG10solid filler (thickened epoxy)foam that stayslid
spar10.3121922.927.7in back of the nose43.544.254749.5in upPOCKETCLAMP BLOCKG10 plate glued on the spar + tab (rear pin)PEX on to the tipPEX up from the root (stands 1/2 in above the floor)G10 shelf on 2 blocksG10 lid frame, one piece2 layers biax: walls and flooractuator (gray dashed)plug above the motor3 biax doublers, both faces4 bolts through both skins and the boom1/4 in G10 plate, glued on, both facesclamp block: foam out, solid fillerboom (straight to 28.5 in, then tapers)notch: wing cut away round the boomdrains (black), flush with the floorfoam stays everywhere else
FROM ABOVE: CUT AT 47 IN UP (THE ROD LINE), ACTUATOR AT MID-STROKElid (orange): the cut-out skinactuatorfront pin (inside the bore mouth)solid filler, both sides of the boomclevis and G10 tab in the short tubespar plate and tab2 layers biaxpushrod in its PEX liner
END: CUT AT 21 IN BACK, LOOKING AFTfoamsolid fillerboomdoublersglued 1/4 in G10 plateboltG10 tab in its tube (mid-stroke)

How the actuator, pushrod and boom fit together

inchesNov 2, 2026
front pin fully in: 18.4middle (flap straight): 19.4fully out: 20.4THE ROD LINE, SIDE VIEW, ABOUT HALF FULL SIZE: actuator fully in (black), fully out (red dashed)spar plate + tabrear pin 11.2 in; fork tip 0.17 in clear of the platefront pin: 10 mm, ring clips, pull it here (fully in)pushrod clevis holding the G10 tab, two pins2 in of bare G10: the lightning gapshort tube: 1 in CPVC, about 0.9 in insidepushrod, 1/4 in, in its PEX liner

How it works

  • Actuator hangs on its two 10 mm pins. Rear pin: a G10 tab on a G10 plate glued to the spar. The motor rests on a padded shelf, two snug ties.
  • Front end: the pushrod's clevis holds a 1/4 in G10 tab with two pins (its own pin and a 10-32 screw). The tab goes into the actuator's fork on the 10 mm front pin.
  • Lightning gap: 2 in of bare G10 between clevis and fork. Nothing metal across it. Keep it clean.
  • Pushrod: 1/4 in 316, about 46-3/4 in, in a 3/8 PEX liner inside the boom. Bare jam nut at the back.
  • Flap straight = actuator at mid-stroke. The front pin then sits 0.4 in inside the boom's bored front (1-1/4 in, 2 in deep).
  • Soft limits: 0.875 in of rod each way = flap 30 deg. Full travel is only about 34 deg; the flap clears 40.
  • Give-way spring is at the flap (tail sheet). Lightning wires: lightning sheet.

Taking it apart

  1. Lid off. Run the actuator to its retract limit. One ring clip off; pull the front pin.
  2. Unplug. Cut the two ties. Pull the rear pin. Tilt the actuator out, motor end first.
  3. Actuator dead mid-stroke? Pull the rear pin, undo the lightning splice, 4 boom bolts out, slide the boom back 2 in, pull the front pin.
  4. Boom off: undo the splice, 4 bolts out, slide it straight back. Tail and pushrod come with it.
  5. Pushrod out (bench): pull the horn's clevis pin, unscrew that clevis counting turns, draw the rod out the boom's front.
  6. Back together: bolts in sealant, 130 in-lb, new paint marks, sealant bead at the notch.

Building the boom, and is it strong enough?

inchesNov 2, 2026
48-1/2 in long: front end 19 in back of the nose; the last 4-1/2 in sits in the tail's slotstraight, no taper: 9.5 in31-1/4 in4 bolt holes, drilled on the benchglass: 3 layers to 17 in, 2 beyond, plus 1 on the sides to 12 insolid: thickened epoxy, no foam (front 3.4 in)1-1/4 in bore, then the short tubethe last 37 in of PEX: the S-bend out to the side (tail sheet)solid tail end, 3 clamp bolts

Building the boom

When: before the pocket.

  1. Core: two 3/4 in H80 strips, 48-1/2 in long. Groove them first (step 2), then glue and plane to 1.16 in wide. Finished, it must stay under 1.65 in wide.
  2. Grooves: half-round, down the middle of each inside face: short tube 2 to 6-1/2 in from the front, then the 3/8 PEX liner. Last 37 in: a smooth S out to the far-face side, ending about 1-5/8 in off center, a little low. Glue tube and PEX in, ends plugged.
  3. Shape: 2.74 in deep and straight for the front 9.5 in. Taper to 1-1/4 in. Last 4-1/2 in straight at 1-1/4 in.
  4. Solid ends: foam out of the front 3.4 in and the last 4-1/2 in. Fill with 406 epoxy, no voids.
  5. Round the long edges to 1/4 in.
  6. Glass (threads along and across, not 45 deg): 3 layers on the front 17 in, 2 beyond, 1 more on the sides to 12 in. Glass over the PEX exit and the front face.
  7. Bore the front 2 in out to 1-1/4 in, on the tube's center line. Chamfer the tube mouth.
  8. Drill 4 bolt holes, 5/16 in, drill press: 1.0 and 2.9 in from the front, 0.45 in in from top and bottom.
  9. Tail end: 3 clamp bolt holes, drilled with the tail on (tail sheet). Weigh it: about 5 lb (a guess).

Strength check (worked out; material strengths are typical)

PartStorm gust, 15 lb at the tailBroadside Cat 3 gust, about 160 lb (an estimate)That x 1.5, 240 lbStrength
Boom just behind the wing900 psi9,400 psi14,200 psiabout 35,000 psi
Boom pressing on its socket120 psi1,260 psi1,900 psifiller 8,000+ psi; foam 200, so the socket is solid
Each bolt, counting no clamp friction at allabout 110 lbabout 1,200 lbabout 1,800 lbabout 3,900 lb
Skin round a bolt hole, no friction (0.5 in stack with the 1/4 in plate)720 psi7,600 psi11,500 psiabout 30,000 psi
Bolt tearing out of the boom toward its top or bottom edge (0.45 in)up and down at 5 g: about 160 lb eachabout 2,600 lb
Skin, doublers and the 1/4 in glued plate pushed out between the bolts1,600 psi16,800 psi25,200 psiabout 30,000 psi
Clamp pressing on the filler816 psi816 psi816 psi8,000+ psi
Twist carried down the wing skins4 lb/in45 lb/in68 lb/insmall for the skin

Biggest load: a Cat 3 gust (gusts about 160 mph, a guess) hitting the feathered tail broadside. Weakest spot: the skin between the bolts, good for about 285 lb at the tail, 1.8 times that gust. Keep the lid's 1/2 in round corners and run the first doubler layer to the spar. Full working: Reference/Boom_Root_Strength_Calc_2026-10-28.

Boom-root pocket: steps and parts

inchesNov 2, 2026

Build steps

When: between the guide's Stage 8 and Stage 9. Build the boom first: it molds its own socket. Skip the guide's Stage 10 root zone, doublers and metal plate.

  1. Mark the pocket (10.3 to 19 in back, 43.5 to 48.75 in up), clamp block (19 to 22.9 back, 44.25 to 49.5 up) and notch (22.4 back to the edge, 45.45 to 48.55 up). Move top and bottom edges to the nearest rib glue lines. Mark the lid edge too.
  2. Cut the foam out of the pocket and clamp block, down to the far skin. Cut the notch through both faces.
  3. PEX: lay both 1/2 in tubes, 12 in back, with pull strings. Root tube: cut long; it runs on through the mast plate. Pull both cables and the 8 AWG ground wire in before gluing (1 ft spare in the pocket, 2 ft below the plate). Scuff and flame the PEX first. Ends 1/4 in deep at the pocket; the bottom one 1/2 in above the floor. Both ends of the root tube stay open.
  4. Glass the pocket floor and walls: 2 layers biax, 1 in lap onto the face. Notch edges: 1 layer.
  5. Lid frame: recess the face 0.2 in round the pocket. Glue in the one-piece G10 frame, half over the opening. Glue #10-24 316 nuts under its inner edge.
  6. Bed the boom: tape and wax its front 9 in. Line it up with a straight board (0.01 in off here is 0.15 in at the tail). Clamp it in the jig. Fill the clamp block with 406 epoxy in 2 or 3 pours. Recheck after the first. Cure, slide out, strip the tape.
  7. Actuator parts: boom back in. A straight 5/16 in rod down its liner places the spar plate and tab (rear pin 11.2 in back, 47 in up) and the shelf. Glue. Tape the spar plate on with biax. Do not drill the spar.
  8. Plug and skin: thin foam on spacers over the pocket, tape on the frame's inner half. Tape the socket mouth. Skin the boom face.
  9. Doublers: 3 layers biax, both faces, 19.4 in back to the back edge: 11.4, 9.4, 7.4 in tall, centered 47 in up. Round the notch, off the lid. First layer runs forward to the spar.
  10. Cut the lid out, 1/2 in round corners. Pull the plug.
  11. Drill the 4 bolt holes through the wing, boom in place, through its holes. Keep the drill straight: 0.3 in from the bore.
  12. Bolt plates: glue the 1/4 in G10 plates on epoxy wedges, square to the bolts (the face slopes 7-1/2 deg). Epoxy fillet round the edges.
  13. Drains: two 3/16 in holes in the far skin, flush with the floor, both ends. Small notch at the lid's lower back corner.
  14. Bolt up: Belleville under each nyloc, blue thread locker, 130 in-lb, paint mark. Bolts in sealant; sealant bead at the notch.

G10 pieces (1/4 in unless marked)

PieceSize
Spar plate2 x 3 in, on the spar's back face
Rear tab1 x 1.3 in, 10 mm hole, sanded to 0.22 in where the fork goes
Flat tab3/4 x 4 in: see the actuator tab pages
Motor shelf4.5 x 3 in, on two 1/4 x 3/8 in blocks, 1/16 in rubber on top
Lid frame1/8 in, one piece: 1 in wide, back 3/4 in
Bolt plates3 x 3.4 in, one on each face

Hardware

  • Four 5/16-18 x 4-1/4 in 316 bolts, Bellevilles, flat washers, nylocs.
  • About 10 #10-24 316 screws and nuts for the lid; gasket tape.
  • Rear pin McMaster 93890A742 (26 mm or more between grooves). Front pin 93890A741 (24 mm), ends cut to 1/16 in past the grooves.
  • Plug: DTM 4-pin kit and crimper. It sits above the motor; grease and boot it.
  • Two coated 316 ties, snug.
  • Tef-Gel on both 10 mm pins and every stainless thread.
  • Pushrod: 89325K113 cut to 54 in, trimmed to about 46-3/4 in; two 6071K47 clevises; 10-32 x 1 in screw and nyloc; bare 1/4-28 jam nut.
  • Clamp block filler: about 0.6 lb of 406 epoxy (a guess).