Tail sits 2/3 above the boom, 1/3 below: 17-1/4 in above center, 9-3/4 in below.
A slot in the tail's front, 1-1/2 in tall, 4.6 in deep; the boom's end slides in.
Two G10 clamp plates, one each side, and 3 stainless bolts through plates and boom.
No breakaway.
The give-way spring is at the flap, in a pocket 1-1/2 in tall in its front edge. The flap stays one piece.
Horn 2 in, hole 1-3/4 in out. Full travel is about 34 deg; the flap clears 40. No stop pins.
The pushrod's PEX comes out the boom's far-face side for its last 24 in, faired in.
Four short hinges, not three.
From the side, 1/5 size
Boom end and tail from below, 1/5 size
The clamp at a bolt, full size
A hinge cut through, full size
Building the tail and flap
inchesNov 2, 2026
Build
Boom: built on the boom pocket sheet (PEX S-bend out the far side, solid last 4.5 in).
Tail: 36 slices as Stage 12, one piece. In the two middle slices cut the slot, 1.5 in tall, 4.6 in deep, and a 1/2 in notch at the back edge for the spring.
Flap: cut the back 2.75 in off, full height. Cut the pocket in its front edge, 1-1/2 in tall, 1.9 in deep, level with the slot. Sand the front edge to a point, 40 deg each side.
Hard spots, before glassing: at each hinge and under each end plate, dig the foam out 1/2 in deep, 2-1/2 in long. Fill with thickened epoxy.
Glass tail and flap. Line the slot top and bottom with 1/8 in G10.
Hinges: four 2 in pieces, two above the pocket, two below. Slots 3/8 in deep in the hard spots. Sand the leaves (80 grit), acetone, glue in with thickened epoxy. Line all four up on a straight rod while it cures.
Flap spring and horn: build it (spring pages). Glue its end plates into the pocket.
Clamp plates: release tape on the boom; slide the tail on. Bed a 1/8 in G10 plate, 3.2 x 4.5 in, each side over the slot, in thickened epoxy, with a fillet round its edges.
Bolts: three 1/4 in holes through plates and boom, 0.3 in above the boom's middle. 2-1/2 in bolts, Belleville under each nyloc, blue thread locker, about 60 in-lb (a guess), paint marks.
Paint the G10 plates and horn: G10 weathers in sun.
Bias spring (stops rattle): about 1/2 lb, 2 to 2-1/2 in long. From the horn's 3/32 in hole forward to a drilled 1/4 in fender washer under the rear clamp bolt's head.
Pushrod: clevis on the horn's 1-3/4 in hole; bare 1/4-28 jam nut. Grease the rod going into the PEX. Rubber boot over the PEX end.
Lightning: boom wire's lug under the rear clamp bolt's head, under the washer. No wire on the pushrod.
Tef-Gel on every stainless thread and pin.
Soft limits: 0.875 in of rod each way (flap 30 deg).
The flap spring and horn, full size (print at 100 percent)
inchesNov 2, 2026
How it works
The two end plates are glued in the pocket's top and bottom, so they turn with the flap. The horn turns free on the axle between them.
Each spring leg presses on one blue pin (horn) and one orange pin (flap) side by side, so the horn and flap turn as one.
A gust stronger than the spring's setting pushes an orange pin, and its leg, off the blue pin: the flap swings toward straight while the actuator holds the horn. The spring brings it back.
Templates and steps: the next two pages.
The numbers and the parts
inchesNov 2, 2026
Numbers (worked out)
Tail 2/3 up: about 1.6 times the root bending of a centered tail, 3.3 times less than on top.
Loads: storm gust about 15 lb on the tail; knockdown about 113 lb (a guess); the boom root gives at about 285 lb (inferred).
Clamp bolts, worst case: about 924 lb each, against about 2,385 lb for a 1/4-20 316 bolt.
Pushrod pull: about 2.3 lb at the spring's setting, 3.2 lb at full give.
Actuator play (0.047 in): about 0.8 deg each way at the flap; the bias spring takes it up.
Pushrod bend: about 21 thousand psi, under 316's 35. It passes 0.75 in outside the clamp plate.
Give-way spring: 4.0 in-lb at rest (41 percent of its rating), 58 percent at full give, only while giving. Kept (Mike, Nov 2).