Wet lab box (A18)

House bus tee ahead of Release Node B | GitBoat v10.5 A18 | Pending 428, closed v10.2a

Status notes
  1. Box plan Decided

    Wet lab box plan. The wet-lab path is relay channel 2 and its own run.

  2. Pending 521 pin map In the guide

    Pending, not yet in the guides. 521 (Pending_Amendments_v10_5.md line 19): "3.3V, GND, CAN RX, CAN TX, in that order"; "3.3V to 25b, GND to 22t, CAN TX to D2, CAN RX to D10"; "with ferrules"; "The 120 ohm resistor (marked 121, just below the CANL and CANH pins) still comes off". 522 line 21: "about 16 min"; "Room for weeks of bursts is a guess"; "The serial lines can't carry orders as wired". Not drawn.

  3. Pending 524 In the guide

    Electronics plan A18: the NUCLEO-G431KB is bought (Ken, DigiKey; Mike, 2026-11-06). Valve 1's second input is A7. The CAN board keeps its header and one RLECS Dupont lead, zip-tied. The surge stands on its own short rail: IN 1 white is H, IN 2 blue is L. 0 V is two bars (16-18 and 19-23) joined by one 22 AWG from block 18 top to block 19 bottom.

    Relay screws read NC, COM, NO; COM and NO are used. 22 AWG on signals and the 1 A and 2 A feeds; 18 AWG on the main 24 V path. The XWST's own leads reach the rail. Opto inputs 1- to 5- are joined.

A18 WET LAB BOX | HOUSE BUS TEE House-bus tee ahead of Release Node B's end tee.House teeown tee A NUCLEO-G431KB (bought: Ken, DigiKey; Mike, 2026-11-06) on an AITRIP Nano screw carrier; an SN65HVD230 CAN board, which keeps its soldered 4-pin header: one RLECS 4-pin Dupont lead pushed on, zip-tied lengthwise over plug and board, a dab of glue, the far plug cut off and the wires under the carrier's screws (the GPS A method, Compute Bay Plan sec 4.1); a Taidacent RS-12V/2S surge module on the CAN drop.G431KBbought XWST 24 V 10 A with a 1.5KE33CA across its output.XWST 24 V10 A Five fuses. F1 Gulper 5 A is the guide's guess: read the label.F1-F5F1 guess All normally open. Ch 1 Iwaki, 2 Kamoer, 3 Gulper, 4-5 valve 1, 6 valve 2, 7-8 spare.8ch NOHiLetgo IN1 flow, IN2-3 valve 1, IN4-5 valve 2. Read valve wire colors off the label.Fafeicyvalve colors Pressure divider 10k / 18k. Celsius on I2C 3.3 V with 4.7k pull-ups.pressure10k / 18k Wet lab 16/2, line 9, 15 A breaker, central relay channel 2. It enters split gland C, port C3.24 V in15 A ch 2 At power-on with no message from Pi A for 60 s, it runs one burst on its own (the solo burst, Flow-Through Wet Lab Design sec 10). In the middle of a burst, 60 s with no message turns every relay off, so the pump stops and valve 2 springs shut.silencesolo burst Plastic IP67 with a mounting plate, about 12 x 8 x 5 in: the TICONN bought 2026-10-03 if it is that size or bigger, else a TICONN of that size (to buy). No vent. No lightning copper.about 12 x 8 x 5no vent CANH CANL power USB Ethernet UART I2C GPIO coax SPI