Wing Power System: Build and Mounting Guide v10.2
v10.2, 2026-10-08. The v10.1 guides with every decision made through 2026-10-08 written in. What is still open is in Pending Amendments v10.3, the only open list. Companions: Build Guide sec 6.6 (the wing's electrics in short) and sec 3.3 (the fixed can and the slewing ring); Wing Can Spec Sheet (the can and its hand-hole); Rig Base Two Plate Design (the ring bolts and the fold); Wing Construction Guide; Wing Trim Actuator Installation Guide; Electronics and Wiring Plan A17 (the wing box's holes and its feed from the bus) and A1a (the USB hub box, where the wing's readers sit); Lightning Ground System Guide secs 5 and 7.5. Scope. The wing's electrics since the slip ring: the slip ring through the wing's turning joint, the wing compass, the trim actuator's cable, the wing-tip wind meter's power and wiring, and the wing box below the deck, where the wing's wires enter the hull. The wing makes and stores no power of its own; it runs from the hull's main bank through the ring. Prices and order status: Bill of Materials sec 15.6. Reasons: Design Decisions R-6.6B. Source study: Reference/Wing_Slip_Ring_Options_2026-09-24.md (the slip ring file; secs 7, 9, 10 and 13); the ring and compass install: Reference/Wing_HC2549_and_Compass_Install_2026-10-01.md; the readers and the timing: Reference/Wing_RS485_Readers_and_Timing_2026-10-07.md.
| Term | Plain meaning |
| Feather | Edge-on to the wind, making no force. The wing's safe resting state |
| Slip ring | Sliding contacts that pass wires across a turning joint. Here a sealed Rion ring on the wing's turning axis, inside the can |
| Fixed side, turning side | The ring's body stays still with the can; its flange end turns with the mast and wing |
| Wing compass | The WitMotion HWT905 compass and gyro at the wing tip: gives the wing's turn rate, and with the hull's heading its angle against the hull |
| Wing box | The small box below the deck where the wing's wires enter the hull; the ring's wires land in it |
| Hand-hole | The opening in the can wall that the ring is reached through |
| Surge part | Does nothing at working voltage and shorts a spike across the pair it guards |
| Wing tab spring link | A spring-loaded section in the tab pushrod. Strong wind pushes the tab straight whatever the actuator does, so feathering never needs power (Trim Actuator Guide sec 6) |
1. The idea in plain terms
The wing turns on a bearing to follow the wind. Since the slip ring (Mike, 2026-09-26), eight wires cross that joint, and the wing carries no battery, solar panel, charge controller, radio or computer, and there is no wing pod. What stays on the wing: the trim actuator (the Thomson Electrak MD) and its cable, the wing-tip wind meter (the Calypso CMI1017) with its small 5 V converter, and the wing compass (the WitMotion HWT905) beside it, both behind the tip's own 1 A fuse. Everything that thinks is in the hull: the wing's program runs on the hull's Pi A, which reads the meter and the compass and talks to the actuator through two isolated adapters in the USB hub box beside it (sec 8.7).
The wing needs very little power
Its one real load is the actuator on the tail's trim tab, holding a small flap against a light spring through a self-locking screw. The rest is the wind meter and the compass. All of it comes from the hull's main bank through the ring (sec 5).
The one guarantee
Safety never depends on the wing's electrics. Feathering needs no power: the wing tab spring link gives way in strong wind and the light hinge spring centers the tab. With no power the tab holds its last trim, harmless in light wind, and in strong wind the wing feathers; the boat loses its sail and shore is told.
1A. The slip ring (the design)
Decided and bought (Mike, 2026-09-26); the ring and the wing compass as below (Mike, 2026-10-01). The ring sits in the can on the wing's turning axis, under the mast plate, and carries eight wires across the joint. It hangs from the foot of the drive tube by its turning flange, goes on at the bench and rides down with the mast lift, with nothing to line up; through the hand-hole one stop bolt keeps its body from turning (sec 8.5). A swap at a refit is the same job in reverse, through the hand-hole, with nothing lifted. Detail: Reference, Wing HC2549 and Compass Install 2026-10-01. [IMAGE] The drawing (Reference/Wing_HC2549_Compass_Install_2026-10-01.png, not to scale) shows the ring on its drive plate, the stop bolt and arm, and the compass at the tip. The ring: Rion HC2549-RZ086-P0410-S03-1C-IP65 (Rion's store is run by Moflon), built exactly as Rion drew it (Reference/Rion_HC2549_Proposal_Drawing_2026-09-30.pdf, 3D file beside it). Rion order 4524; due about 2026-10-20. From Rion's drawing:
- 3.4 in (86 mm) across; about 4-1/8 in (105 mm) long, flange to tabs; the two tabs reach 4.8 in (122 mm) tip to tip.
- Turning end: a flange 3.4 in across and 5/32 in (4 mm) thick, with four slots 1/4 in (6.5 mm) wide on a 2.76 in (70 mm) circle. A raised ring 1.57 in (40 mm) across sits in its middle, and the turning-side leads come out inside it.
- Fixed end: two flat tabs, 5/32 in thick, each with an open slot 3/8 in (9.5 mm) wide; three cable glands off center on the end face.
- Four 10 A power rings on 16 AWG Teflon leads; a CAN pair with its own shield ring and an RS-485 pair with its own shield ring, on separate shielded cables. Leads about 10 in (250 mm) each side.
- IP65 (dust-tight and splash-proof, not for under water), aluminum housing, 0 to 60 rpm. Drag up to 35 in-lb (4.0 N-m), Rion's estimate of the twisting force it takes to turn.
The eight wires:
| Ring | Wire | Carries |
| 1 and 2, 10 A | 24 V + and − | The actuator; and the tip branch, through its own 1 A fuse: the wing compass and the tip's 5 V converter |
| 3 and 4, 10 A | RS-485 A and B | The wing compass, on its own pair |
| 5, 6 and 7, shielded cable | RS-485 A and B, and shield | The tip wind meter. Ground the shield at the hull end only |
| 8, 9 and 10, shielded cable | CAN H and CAN L, and shield | The actuator (J1939), on its own CAN link. Ground the shield at the hull end only |
The compass has its own pair on the two spare power rings, so a fault on the tip meter's pair cannot silence it, and the tip meter keeps its plain wind format (NMEA 0183). The 24 V is not doubled: the actuator's 2.6 A peak is about a quarter of one ring's rating. The wing compass: WitMotion HWT905, RS-485 version (it also comes as RS-232 and CAN). A compass and gyro in an IP67 aluminum case with a cable about 39 in (1 m) long; bought 2026-10-02 (Bill of Materials sec 15.6). It needs 9 to 36 V and draws under 40 mA (WitMotion's HWT905-RS485 datasheet, sec 3.1), so it runs on 24 V, never on 5 V. It speaks Modbus RTU (a simple ask-and-answer format) and answers only when asked. Its gyro gives the wing's turn rate for the rate damper; its heading minus the hull's heading gives the wing angle against the hull, good to a few degrees (a guess), enough for the spring link check and for turning the tip wind into boat directions (Wing Trim Actuator Installation Guide, the rate damper). Open: its wire colors; its label settles them when it lands.
- It sits on a G10 pad, 1/4 in thick, about 3 x 2 in, glued on the tip cap at Wing Construction Stage 11, with two nylon or 316 screws (never plain steel), its arrow pointing at the nose along the chord. Keep it at least 4 in from the strike rod's base, the bird spikes and the 5 V converter.
- It runs on the tip branch's 24 V, after the branch's 1 A fuse and ahead of the 5 V converter, which feeds only the tip meter; its pair rides rings 3 and 4. Its joins sit in the tip box with the fuse and the converter (sec 8.6). Open: where the tip box and the compass pad sit on the tip; the tip mount drawing settles it.
- A strike that kills the tip meter will likely kill the compass too; the wing then trims without the damper until a refit (Mike accepted this, 2026-10-01).
The mount in the can:
- Fixed side: a 316 post welded to the center of plate 3 by the welder, in the same visit that welds the can to plate 3 (Mike, 2026-09-28); its size and height: Wing Can Spec Sheet. On it, a stop arm of 316 flat bar, 1/4 x 1 in, about 4 in long, running out from the center, with a slot 5/16 in wide and 1-1/2 in long across the arm, centered about 2-1/4 in from the post's center, about 2-1/2 in below the ring's tabs so the fixed-side cables have room to drop and turn. The post also carries the lightning brush's bracket. Open: the stop arm and the brush bracket on the can's build drawing.
- Stop bolt: a 5/16-18 316 bolt about 4 in long through one tab's slot and the arm's slot, with a 316 spacer tube to fill the gap, nylon washers on both faces of the tab and a nylock nut. The crossed slots take up any offset of the post.
- Turning side: a 316 drive bar hangs under the mast plate from two opposite inner-ring bolts of the bearing, so its middle is the turning axis with no measuring. Those two bolts are 1/2 in longer than the rest, about 5/8-11 x 3 in, still to buy (Bill of Materials sec 15.6; the bolt rules: Rig Base Two Plate Design, "Slewing ring bolts"). The drive tube, 1 in 316, bolts under the bar's middle. On the tube's foot is welded a drive plate: 316, 1/4 in thick, 3-3/8 in round, four 9/32 in holes on the ring's 2.76 in slot circle, and a 1-3/4 in center hole that clears the raised ring and the leads, with the tube's bore open through it. The ring's turning flange bolts under it with four 1/4-20 x 3/4 in 316 bolts and nylock nuts, a 1/16 in G10 gasket between, which keeps the ring's aluminum off the stainless.
- Bar and tube are the brush's path (Mike, 2026-09-28): both 316, bolted metal to metal, so the path runs mast plate, the two longer inner-ring bolts, bar, tube, brush. Tef-Gel on the threads only; bare metal where the bar meets the bolt heads and the tube. The Helwig lightning brush rides sideways on the drive tube, below the bar and above the drip cup (Lightning Guide sec 5.2).
- Heights, down from the underside of the mast plate: the drive bar; about 3 in of tube (the brush's zone, then the cup's top); the drive plate and gasket, about 5/16 in; the ring, about 4-1/8 in to its tabs; about 2-1/2 in to the stop arm. That puts the stop arm about 10 to 11 in below the mast plate (an estimate; the can's build drawing settles it).
- The hand-holes: Wing Can Spec Sheet, "The hand-hole".
The cables.
- Turning side, the mast cable (eight wires). The ring's turning-side leads end in sealed Deutsch DT plugs (crimped plugs rated for immersion when mated; no solder). They meet the mast cable, which runs down the hollow mast and the drive tube and out through the drive plate's center hole; tuck the joined plugs up into the tube's mouth or tie them to the tube just above the plate. The mast cable enters the mast bore through a 3/4 in hole at the mast plate's center, drilled before the pipe is welded on (the mast weldment: Wing Construction Guide Stage 4), and leaves the mast through a hole in its wall inside the wing root, into the wing's trailing-edge conduit. Open: where that wall hole goes, how the cable crosses the socket and the root to the conduit, where it meets the actuator and wing cables, and which cable carries the eight wires down the mast; settle them before the mast is welded and before Wing Construction Stage 6 builds the socket.
- Fixed side. The ring's three fixed-side cables each drop straight about 2 in, then turn to the can-wall gland and plug into a hull cable (Deutsch DT), with a drip loop in each. The hull cables go down through their own fixed watertight deck gland, clear of the plate, with a loop of slack at the tilt hinge, straight into the wing box below the deck (Mike, 2026-10-02). Open: the exact route from the can-wall gland to the deck gland; the can's build drawing and the wing box's hole schedule settle it.
Keeping the can's damp off it. The can is wet: salt air, condensation, and now and then a wash past the wing-root disc that leaves by the weep holes (Wing Can Spec Sheet).
- A drip cup: a plastic hat about 6 in across (so it passes the hand-hole), slit from its center hole to its edge, closed round the drive tube with a stainless hose clamp below the brush and above the ring; its skirt ends above the tabs. Never a boot clamped at both ends: the wing can wind up many turns one way over a voyage, and a boot would twist off.
- Tef-Gel on every bolt (on the drive bar's bolts, threads only, above). The G10 gasket keeps the ring's aluminum off stainless.
- Wipe a corrosion blocker (Boeshield T-9 or CorrosionX) on the ring's outside and its bolts at fitting and at each refit, mainly where the turning end meets the body, since the seal rides there.
- A drip loop at every cable entry, so water runs off the wire, not into the ring.
The wing box, where the eight wires land: sec 8.7. The tip's supply: secs 2 and 8.6.
2. The electrical backbone (every voltage, in one place)
| Rail | Where it comes from | What lives on it |
| 24 V | The hull's main bus to the wing box (its branch and breaker or fuse: Electronics and Wiring Plan A17), then the box's 5 A fuse and surge diode (sec 8.7), up across the ring's power rings 1 and 2 | The actuator: 0.6 A unloaded, 2.6 A at full load, under 2 mA asleep. The tip branch, through its own 1 A fuse: the wing compass (9 to 36 V, under 40 mA) and the tip's 5 V converter |
| 5 V at the tip | A sealed 24 to 5 V converter at the tip (sec 8.6) | The Calypso CMI1017 only |
| CAN | The actuator's own link: the ring's shielded CAN pair, the wing box's surge module, then the shielded cable to the USB hub box and its isolated USB to CAN adapter, on its own lead to Pi A (sec 8.7); a 120 ohm resistor across the pair at each end (at the actuator, and the adapter's switch) | The Electrak MD alone, off the boat's two buses |
| RS-485, tip meter | The ring's shielded RS-485 pair, then the shielded cable to the hub box's isolated 2-channel reader (sec 8.7); its ground is the shared 24 V −, carried to the reader on the cable's ground pair | The CMI1017 alone |
| RS-485, compass | The ring's power rings 3 and 4, then the same cable to the reader's second channel; its ground is the shared 24 V −, on the same ground pair | The HWT905 alone |
Never put 24 V on either Calypso meter. Both take 3.3 to 18 V, and their inputs carry clamping diodes that conduct hard at 24 V: wired straight, a meter dies at first power-up. The wing compass is the other way round: it needs 9 to 36 V and never goes on the 5 V. The actuator's 24 V is never switched: the MD sleeps on its own after bus inactivity, under 2 mA.
3. What lives on the wing (parts overview)
| Part | What it is |
| Tab actuator | Thomson Electrak MD (MD24A025-0050CNO), about 2.4 lb, in the sealed boom root fairing 47 in up (Trim Actuator Guide sec 2). The only real power user |
| Actuator cable | The tinned 18/4 shielded cable, 0.26 in across, up the trailing-edge conduit: the 24 V pair and the CAN pair (sec 8.6) |
| Wind meter | Calypso CMI1017 ultrasonic at the wing tip, RS-485: the boat's backup wind reading and the post meter's cross-check. It stays (Mike, 2026-09-26) |
| Wing compass | WitMotion HWT905, RS-485, on a G10 pad on the tip cap, on the tip branch's 24 V (sec 1A) |
| Tip fuse and converter | The tip branch's sealed 1 A inline fuse, for the compass and the converter; a sealed 24 to 5 V converter at the tip, for the meter only (sec 8.6) |
| Wing cable | Three shielded pairs, 24 V, the tip meter's RS-485 and the compass's RS-485, down the trailing-edge conduit beside the actuator cable (sec 8.6) |
| In the can, not on the wing | The slip ring (sec 1A) |
Nothing else: no battery, panel, charge controller, radio, computer, pod, potting or pod fuses. Their weight left the wing with them, and the packs were nose weight, so the nose lead is re-set at Wing Construction Guide Stage 10.
4. The three power sources
None since the slip ring (2026-09-26): the wing makes and stores no power, and draws from the hull's main bank through the ring (sec 2). Why: Design Decisions R-6.6A and R-6.6B.
4.1 Solar panels in the wing skin
None: no panels, panel pockets or lead channels on the wing.
4.2 Charging across the bearing (the hull link)
None: the ring carries the hull's 24 V across the joint (sec 1A).
4.3 The two packs, as one bank
None: the wing carries no battery.
5. What the wing draws from the hull
The wing's loads now come off the hull's main bank. Figures are watt-hours a day (Wh), carried over from the old wing budget.
| Draw | Wh a day | Basis |
| Actuator moving, full active trimming | 9.6 | 0.4 W average |
| Actuator asleep, its own controller | 1.2 | Under 2 mA at 24 V, published |
| Wind meter (Calypso CMI1017) and its tip regulator | 0.5 | 0.25 mA at 5 V, plus the regulator. Figured for a Pololu D36V6F5; measure the tip converter's own draw at the bench |
| Wing compass | About 5 (planning figure) | A seller's sheet gives 9 mA at 12 V: about 2.6 to 5 Wh a day at 24 V, carried at the high end. WitMotion gives only a ceiling, under 40 mA (about 23 Wh a day at 24 V) |
The hull-side adapters that read the meter and the compass and talk to the actuator (sec 8.7) run on Pi A's 5 V, not on the wing's feed: the Waveshare reader's draw is not published (about 0.1 A at 5 V, a guess from typical chip figures), and the CAN adapter's is not known. Measure the wing box's draw at first setup (sec 10) and put it in the hull load table (Build Guide sec 4.6), in place of the old charging link's.
6. Running low: shedding load and turning off damping
The wing has no battery of its own. Trim and damping shed with the hull's load-shed ladder (System Settings Sheet sec 4), and shedding either is safe (Trim Actuator Guide sec 8).
6.1 When the wire goes quiet (in place of the radio link)
There is no wing radio: the actuator is on a wire. If its CAN link goes quiet (the Pi hangs or is dark, the hull end fails, or a wire breaks), the MD stops and holds its last trim, and strong wind still opens the wing tab spring link and feathers the wing (Trim Actuator Guide sec 5). A quiet link needs no feather rule of its own.
7. Where everything sits on the wing (the map)
- The wing's bottom edge is about 21 in above the deck; the wing rises 6.5 ft. The root, the bottom 2 ft, wraps the mast top.
- The tab actuator sits at the boom root, 47 in above the wing's bottom edge, in a small sealed fairing, fed up the trailing-edge conduit (sec 8.6).
- The wind meter stands on a short arm ahead of the nose at the tip, with its converter at the tip (sec 8.6); the wing cable shares the trailing-edge conduit.
- The wing compass sits on a G10 pad on the tip cap (sec 1A).
- The mast cable runs down the hollow mast from the root to the slip ring (sec 1A).
- The slip ring sits in the can on the turning axis, under the mast plate (sec 1A).
- The wing box sits below the deck, where the wing's wires enter the hull (sec 8.7).
- The lightning strap runs outside the skin, on one face: 1 x 1/16 in copper, one 72 in stick plus a short piece lapped near the root, from the rod base down the spar line to a bolt on a mast-base gusset, with a braid jumper to the boom-root clamping plate (Lightning Guide sec 5.1). The rod is 15-1/2 in, bolted at the tip, its top 12 in over the tip, above the wind meter. No wing wiring touches the strap.
- The nose locker holds lead only (Wing Construction Guide Stage 10).
8. Building and mounting it, step by step
8.1 Order of work
- Order the mast weldment with the 3/4 in hole at the mast plate's center, drilled before the pipe is welded on (Wing Construction Guide Stage 4), and the wall hole for the cable once its place is settled (sec 1A).
- Get the can welded with its hand-hole and the slip ring post (Wing Can Spec Sheet): the welder welds the post to the center of plate 3 in the same visit, so its size and height and the brush bracket are settled before the can goes (sec 1A).
- Build the wing (Wing Construction Guide): the trailing-edge conduit glued in from the root past the boom root to the tip before the edge closes, its pull string proved, and the cable road from the mast into it built as settled (sec 1A).
- Pull the actuator cable and the wing cable together at Stage 10, on the pull string. Nothing can be added to a sealed wing later.
- Wire the tip branch: its 1 A fuse, then the compass and the tip converter, both on the 24 V after the fuse; then the meter, after checking 5 V at the meter's end of the converter's lead (sec 10). Set up the compass on the bench first (sec 8.5).
- On the bench, mast upside down: bolt the 316 drive bar under two opposite bearing bolts (the two longer ones), bare metal under the heads; bolt the drive tube, drive plate end down, under the bar's middle, bare metal to metal, Tef-Gel on threads only; run the mast cable down the mast and the tube so its plugs hang out through the drive plate's center hole.
- On the bench, the ring: crimp sealed DT plugs on the ring's turning-side leads and plug them into the mast cable; tuck the joined plugs up into the tube's mouth or tie them to the tube just above the plate. Lay the G10 gasket on the drive plate and bolt the ring's turning flange to it with the four 1/4 in bolts, Tef-Gel on the threads; the ring now hangs from the tube and its body turns freely by hand. Coil the fixed-side leads and tape them to the body; wrap the ring in cardboard or a towel for the lift.
- In the can: fit the stop arm on the post welded at plate 3's center, and the brush bracket. Bring the hull cables in through the can-wall gland, each ending in its DT plug (sec 1A).
- Lift the mast on as already planned (Rig Base Two Plate Design). Lower it slowly at the end, so the ring clears the post and the stop arm. Nothing has to engage.
- Last, through the hand-hole: the lightning brush, then the stop bolt and the fixed-side plugs (sec 8.5).
- Wire the wing box and its cable to the USB hub box (sec 8.7) and run the checks in sec 10.
8.2 Solar panels into the skin, so nothing can rip off
None since the slip ring: no panel pockets, lead channels or extra plies under pockets (Wing Construction Guide Stages 7 to 9).
8.3 The two battery packs in the nose locker
None since the slip ring. The nose locker holds lead only, and the lead is re-set at Wing Construction Guide Stage 10, because the packs were nose weight.
8.4 No backup cell
None: there is no battery of any kind on the wing.
8.5 Fitting the slip ring and the wing compass (in place of the hull link)
Through the hand-hole, last, with the mast on and the ring already hanging from the drive tube (sec 8.1). First the lightning brush, so its sanding grit is cleaned out before the ring is unwrapped:
- Fit the Helwig brush on its bracket on the post, pressing sideways on the drive tube below the bar. Wrap sandpaper round the tube, grit out, and turn the wing by hand so the tube wears the brush's face to its curve; take the sandpaper off and clean the tube. No grease where the brush rides. The brush's spring force is not known: check the tube and drive plate do not move under its push. Meter mast to can under 0.1 ohm (Lightning Guide sec 8.1).
Then the ring:
- Take off the wrap.
- Turn the ring's body by hand until one tab's slot sits over the stop arm's slot.
- Put the stop bolt down through both slots: nylon washer, tab, nylon washer, spacer tube, arm, nut. Snug the nut. Nothing is forced: the ring already sits where the drive tube put it, and the crossed slots take up any offset of the post.
- Untape the fixed-side leads. Let them drop straight down about 2 in before they turn toward the gland, then plug each into its hull cable. Leave a drip loop in each.
- Wipe the corrosion blocker on the ring's outside, mainly where the turning end meets the body, and on the bolts.
- Hang the drip cup round the tube by its slit and tighten the hose clamp.
- Bolt the hand-hole cover on.
To swap the ring at a refit: the same steps backward through the hand-hole, four bolts overhead at the drive plate, the stop bolt and three plugs. Nothing is lifted, and the ring never needs the mast off. The wing compass.
- On the bench: power it from 24 V and connect it to a PC through a USB to RS-485 adapter with WitMotion's free software. Leave its address as it comes (it is alone on its pair). Set its speed to 115,200 baud (it comes set to 9600; System Settings Sheet sec 8): a poll for turn rate and heading then takes about 2.3 ms on the wire, against about 28 ms at 9600. Check the heading follows as you turn it by hand. Read its label for its wire colors.
- At the tip, at Stage 11 or at fit-out: glue the pad on the tip cap, square to the mast with the boat upright, so the compass sits level, at least 4 in from the strike rod's base, the bird spikes and the 5 V converter; leave the spikes off that patch. Screw the compass on, arrow to the nose along the chord. Run its cable to the tip box with a drip loop, in through a gland. In the box, splice its power and ground to the tip branch's 24 V after the 1 A fuse, ahead of the converter (never to the converter's 5 V output), and its A and B to the wing cable's third pair (crimped heat-shrink splices, no solder).
- Once on the boat, on the hard or in calm water: the magnet calibration and the angle table (sec 10).
8.6 Wiring and keeping water out
- All wire on the wing is marine tinned. No soldering on the boat and no soldered field wires (Electronics and Wiring Plan sec 4): every joint is a crimp with glue-lined heat shrink over it, a lever connector, a screw terminal or a sealed crimped plug, with a service loop (a little slack) at every wire end. A board's terminal blocks may be soldered on once at the workbench, before it is installed. Every wire exit is through a gland or potted. Nothing touches the lightning copper strap.
- The actuator run: the tinned 18/4 shielded cable, 50 ft (Amazon B0D9JV83HJ, $36.99, bought 2026-09-21), up the trailing-edge conduit: the 24 V pair, and the CAN pair (a rugged two-wire data link) with a 120 ohm resistor across it at each end. The shield crosses the ring on the CAN cable's own shield ring (sec 1A); ground it at the hull end only. Open: whether the wing-side shield is landed, and on what; the wing's cable route settles it. The run, its glands and its drip loops at the actuator: Trim Actuator Guide sec 4 Step 4.
- The trailing-edge conduit (Wing Construction Guide Stage 10) carries the actuator cable and the wing cable and nothing else, both pulled at Stage 10 on the pull string left at the wing build. It is 5/8 in inside diameter or more; check its bore against both cables before it is glued in.
- The tip's feed: the wing cable carries a 24 V pair, branched off the ring's 24 V pair, the tip meter's RS-485 pair (another rugged two-wire link) and the compass's RS-485 pair, up the conduit to the tip. There, in a small sealed tip box, the 24 V pair goes through its own sealed inline 1 A fuse. After the fuse it feeds the compass straight, and a sealed 24 to 5 V converter, the DROK sealed converter bought for this job (Bill of Materials sec 15.6), which makes the 5 V for the tip meter only. The 1 A fuse keeps a fault at the tip from blowing the actuator's 5 A fuse. Where the 24 V branches off at the root is part of the root route (sec 1A). Open: where the tip box sits in the tip mount; the tip mount drawing settles it.
- The wing cable is not bought yet (Wire and Cable Buy List C5, on hold): three twisted pairs, shielded, about 22 AWG, about 0.3 in across (a guess until it is picked), about 8 ft with its loops from the tip to the root, more if it runs on down the mast; it goes beside the 0.26 in actuator cable in a 5/8 in bore. Pick it before the conduit is sized.
- The boom root fairing and the nose locker each have a small waterproof breather.
8.7 The wing box
The hull end of the slip ring (Mike, 2026-09-26): a new small box below the deck, where the wing's wires enter the hull. The ring's eight wires land here. Every wire from the ring gets a fuse or a surge part at this box's entries, so a strike on the mast stops here and does not reach the other boxes.
| Ring wires | At the wing box entry |
| 24 V pair | The 5 A fuse that feeds the actuator (slip ring file sec 12), then a 1.5KE33CA surge diode across the pair. The diode starts to conduct at 31.4 V, above the bus's charge ceiling; it works both ways, so there is no polarity to get wrong |
| CAN pair | A Taidacent RS-12V/2S DIN-rail surge module, the 12 V option (Amazon B0BGL675ND), then the shielded cable to the hub box. Each module's ground terminal goes to the box's 24 V negative terminal, as the battery bus surge modules' do, so the boat keeps its one bond wire |
| Tip meter's RS-485 pair | A second Taidacent RS-12V/2S, then the shielded cable to the hub box |
| Compass's RS-485 pair | A third Taidacent RS-12V/2S, then the shielded cable to the hub box |
A shorted surge diode (rare) blows the 5 A fuse: the wing loses trim, and the hull is never shorted.
- The trim actuator stays on its own CAN link, off the boat's two buses.
- Open: the box's hole schedule (its glands include one for the shielded cable to the hub box), its material and whether it takes a vent; writing the wing box layout settles it (Electronics and Wiring Plan A17).
- The box's 24 V feed from the bus: Electronics and Wiring Plan A17 and sec 7.6.
What reads the wing and talks to it (Mike, 2026-10-07). Nothing in the wing box thinks. One shielded cable runs from the wing box to the USB hub box beside Pi A (Electronics and Wiring Plan A1a), one long run with one gland at each end. A 4-pair shielded cable fits. It carries the actuator's CAN pair, the tip meter's and the compass's RS-485 pairs, and a ground pair tied to the wing's 24 V negative in the wing box. The ground pair is needed because an isolated adapter's signal side floats: it must share a reference with the sensors, or the signals drift out of range. The cable is any shielded Cat6, all copper, with a shield over all four pairs (Mike, 2026-10-09; what to look for, pairs and colors: Wire and Cable Buy List C8). Its shield is grounded at the wing box end only (Mike's OK, 2026-10-09), on the box's 24 V negative terminal, and trimmed back at the hub box, touching nothing: the strike comes in at the wing box, so the shield drains there and does not carry a surge into the box beside Pi A (Electronics and Wiring Plan A17). In the hub box:
- The tip meter and the compass: one Waveshare USB TO 2CH RS485 (SKU 27646), an isolated 2-channel USB to RS-485 reader with FTDI chips, clipped on a rail and plugged into one port of the USB hub. RS-485 terminators off: at 115,200 baud the run is far too short for echoes on the line to matter.
- The actuator: one DSD TECH SH-C30G isolated USB to CAN adapter (Linux sees it as a standard CAN port), on its own short USB lead to Pi A's second USB port, not a hub port, so the wing's control never depends on the hub. Its 120 ohm switch on; the actuator end has the other. Both channels of Pi A's CAN HAT carry the boat's two buses, which is why the actuator needs a port of its own.
- Why isolated: these lines come straight from the wing box, the box that takes a mast strike. For a split second a strike can put the wing box's ground far from Pi A's. Over a plain copper path that would push current down the ground wire into the hub and Pi A; an isolated adapter has no copper across its gap, so the surge stops at an inexpensive part (Lightning Guide sec 7.5).
Timing. The rate damper needs the wing's turn rate under 100 ms old (Wing Trim Actuator Installation Guide, the rate damper). So: the compass is set to 115,200 baud at its set-up (sec 8.5) and polled 20 times a second for its turn rate and heading; the tip meter sends its wind sentences once a second, and the program finds its speed at start-up by trying the standard rates; a device rule on Pi A sets each FTDI chip's USB latency timer (how long the chip holds a part-filled message before sending it) to 1 ms; the wing program runs on Pi A as its own high-priority process; every reading carries the time it was taken, and the damper skips any reading over 100 ms old. A reading is then about 5 ms old when the command goes out. Settings: System Settings Sheet secs 8 and 9. Detail: Reference, Wing RS-485 Readers and Timing 2026-10-07.
8.8 The watchdog: built in, no Nano
None on the wing: there is no wing computer. The wing's program runs on the hull's Pi A, under the hull's watchdogs (Compute Bay Plan sec 4.3).
9. What happens when things fail
Losing the wing's electrics is never a safety failure: every row ends with a wing that can feather.
| If this fails | What happens | Why it is OK |
| A ring contact, or the ring (about 3 to 5 in 100 over two years, a guess) | No trim (a 24 V or CAN ring), no tip wind (the meter's RS-485 ring) or no compass (ring 3 or 4) | The tab holds; in strong wind the link gives and the wing feathers |
| A surge part fails shorted | The 24 V diode blows its 5 A fuse; a shorted module takes its pair down | The hull is never shorted, and the wing still feathers |
| The trim wiring or the actuator | No active trim | The tab holds; in strong wind the link gives and the wing feathers |
| The CAN link goes quiet (the Pi hangs or is dark) | The MD stops and holds its last trim | The link is still the fuse; the Pi's watchdog restarts it (Compute Bay Plan sec 4.3) |
| Pi B is in command (Pi A down) | Nothing reads the wing or sends trim: the wing holds its last trim, with no damper | The tab holds; in strong wind the link gives and the wing feathers |
| A fault at the tip | Its 1 A fuse blows: no tip wind reading | The actuator keeps its power; the post meter is the primary |
| The compass goes quiet | The software marks the wing angle stale and turns the damper off | The wing still trims, and the spring link still lets it swing into the wind |
| Hull power to the wing box | No trim, no tip wind | The tab holds; the wing feathers in strong wind |
| A direct lightning hit | May kill the actuator, the tip meter, the compass or the ring | The wing box's entries stop it there, and the isolated adapters in the hub box stop what gets past; a dead wing costs trim, not the boat |
10. Testing (part of the Build Guide sec 11 campaigns)
Bench, the tip supply
With 24 V on the meter cable's power pair and the meter not yet connected, read the meter's end: 5 V. Only then connect the meter.
Bench, fail-safe
The two proof tests of the Trim Actuator Guide sec 7, both required, on the bench and again on the boat:
- Test 1, the fuse opens: rod locked at full extension, power off. Pulled toward straight with a hanging scale at the trailing edge, the tab moves at about 1.5 lbf and reaches near straight; the witness marks on the link do not move.
- Test 2, the hinge spring centers the tab: pushrod off, deflect the tab by hand and release: it returns to within 2 degrees of straight, both ways.
Not a test: cutting power and expecting the tab to spring straight. With a self-locking actuator it cannot pass and proves nothing.
Bench, the quiet wire
Stop the CAN messages: the MD stops and holds its last trim, and resumes when they come back. Never a latch-off.
On the boat, the full swing
- With hull power on, turn the wing slowly through its full swing: the actuator answers and the tip meter and the compass read at every angle, so all eight wires are continuous.
- Calibrate the compass, once, on the hard or in calm water: start WitMotion's magnetic calibration over its RS-485 pair, turn the wing slowly by hand through two full turns, then stop it; the strike rod, spikes, actuator and mast turn with the wing, so their pull calibrates out. Then the angle table: paint marks every 30 degrees on the mast plate and the can lip, turn the wing to each, and save the compass heading minus the hull heading; the 12 numbers become the hull software's wing angle table (setting: System Settings Sheet sec 8).
- Record what the wing box draws with the wing resting and while the actuator trims, and add the figures to the hull load table (Build Guide sec 4.6).
On the water and in the storm tests
After the closure checks and the high-wind buffet run (Build Guide sec 11.2): inspect the fairing gland and the tip mount, and confirm the wing still feathers and trims.
11. Parts list (the wing's electrics)
Prices and order status: Bill of Materials sec 15.6. Everything bought for the old wing power is on the order tracker's "Send back for refund" tab (BOM_v10_0_Order_Status.xlsx).
- In the can: the Rion HC2549 slip ring; the drive plate (316, welded on the drive tube's foot) and its 1/16 in G10 gasket; the 316 drive bar and the 1 in 316 drive tube; the 316 post (welded to plate 3 with the can) and its stop arm; the stop bolt, spacer tube, nylon washers and nylock nut; four 1/4-20 x 3/4 in 316 flange bolts with nylock nuts; sealed Deutsch DT plugs; the slit drip cup and hose clamp; the two longer 5/8-11 bolts for the drive bar; Tef-Gel; Boeshield T-9 or CorrosionX.
- The wing box: the box and its glands; the 5 A fuse in a sealed holder; a 1.5KE33CA surge diode; three Taidacent RS-12V/2S modules; the shielded 4-pair cable to the USB hub box (sec 8.7).
- In the USB hub box: one Waveshare USB TO 2CH RS485 isolated reader (the tip meter and the compass) and one DSD TECH SH-C30G isolated USB to CAN adapter (the actuator), both bought 2026-10-07 (sec 8.7).
- On the wing: the tinned 18/4 shielded actuator cable (bought); the wing cable, three shielded pairs (not bought); the WitMotion HWT905 compass on its G10 pad; the tip box; the DROK sealed 24 to 5 V converter at the tip and the tip branch's sealed 1 A inline fuse; glands.