VESC A box build guide

0 of 20 steps

Decided for this box

Based on GitBoat main, Oct 24, 2026 (v10.3 + Pending v10.4). Every wire: VESC_A_Box_Wiring_2026-10-14. Capacitor hookup: Cap_Board_Drawing_2026-10-14. Two-page print: VESC_A_Box_Build_Sheet_2026-10-26.pdf.

Still open: ask Mike

Nothing left to ask for this box (Oct 26).

Still to read off the parts in step 2: the servo, sensor and switch plug types, the motor lead size and the floor screw threads.

Build steps

Settings card

VESC Tool, at first power-up (step 20). From System Settings Sheet sec 2.

SettingValue

On hand and Needed come from the order tracker and the guides as of Oct 24. Parts marked Not fitted stay visible so they are not fitted. A photo marked similar part is not the exact one.

Gather checklist: VESC A box

Click a part's name to see what it looks like. Tick it when it is in the pile. Ticks are saved in this browser only.

Floor plan, lid off

Drawn from Mike's photo of the parts in the box (Oct 26), looking down with the battery end on the left and the motor end on the right. About to scale, 1 grid square = 1 in; inside about 11.2 x 7.6 in. Corners: 1 top-left, 2 top-right, 3 bottom-right, 4 bottom-left. Mirror it if the box sits the other way.

+ post MGI 3/8 in − post MGI 3/8 in + WAGO − WAGO 4 capacitors 1,000 uF 63 V stripes to minus FLIPSKY 75200 Pro V2.0 5-1/8 x 2-11/16 in on the gap pad, 4 screws from below CAN USB switch (shorted plug) sensor COMM, servo U joint V joint W joint lug to lug, 3/8 in bolt, heat-shrink over USB lead, coiled for VESC Tool, lid off desiccant floor = cooling plate glued to the hull with the #120 grit epoxy Pi A cable: kill to servo PPM, ground to servo GND, 10k from COMM 3.3V to PPM + − 2-3/8 infrom 1 5-7/8 infrom 1 Φ1 2-1/2 infrom 2 Φ2 4-1/8 infrom 2 Φ3 5-3/4 infrom 2 C CAN · 7-3/8 in from 1 S U sensor · 6-5/8 in from 4 Pi A cable · 7-5/8 in from 4 1 2 3 4 BATTERY END MOTOR END TOP SIDE BOTTOM SIDE
battery plus and motor leadsbattery minusCANPi A cable (UART and kill)motor sensor

From the photo: the Flipsky is 5-1/8 x 2-11/16 in (130 x 68 mm, Flipsky's spec), its battery leads come out the end toward the posts and its motor leads out the other end. The switch and sensor plugs are on the side toward the bottom wall, CAN and USB on the side toward the top wall, COMM and servo at the motor end. The power button and its lead come out: the shorted plug replaces them. The USB lead stays coiled inside for VESC Tool with the lid off (Claude's pick). The box has a ledge with holes along each end wall and a boss low on each long side: keep studs and holes clear of them.

Mounting: how each part fixes down

PartFixingHole
Box to hullFloor glued straight to the hull in the heat-carrying epoxy, a glass tab round the edge, a strap or bolts into a glued-on pad as backup. Wired to nothing.none
FlipskyFour 316 flat-head screws from outside, up through the floor into its own threaded holes (1-9/16 x 4-23/32 in apart; full-size sheet Flipsky_Hole_Pattern_2026-10-26), heads flush, before the box is glued. Gap pad between board and floor. It stays in for good (Mike, Oct 26).to its holes, countersunk outside
Power postsThe same kind of studs, two per post (a guess at the post's base holes).to its holes, countersunk outside
Capacitors and WAGOsGlued to the floor with neutral-cure silicone, stripes all one way, levers up.none
Phase jointsLug to lug on a 3/8-16 x 1 in 316 bolt, washer each side, nyloc. Glue-lined heat-shrink over. The three tied into a tight bundle.none
Plug leads, desiccantZip ties; the desiccant on a dab of the silicone.none

Wire list

FromToWire

Hole map

Each drilled wall seen from outside, rim (lid side) up. Number the corners on the box as on the floor plan first. All eight centers 1 in below the rim. Battery end: + and −. Motor end: the three motor leads. Top side: CAN. Bottom side: sensor and Pi A cable. No vent.

BATTERY END · from outside 1 4 + − + 2-3/8 in, − 5-7/8 in, from corner 1 · 7/8 in holes 1 in MOTOR END · from outside 3 2 Φ3 Φ2 Φ1 Φ1 2-1/2, Φ2 4-1/8, Φ3 5-3/4 in from corner 2 · 7/8 in 1 in BOTTOM SIDE · from outside 4 3 S U S 6-5/8 in, U 7-5/8 in, from corner 4 · 1/2 in holes 1 in TOP SIDE · from outside 2 1 C C 7-3/8 in from corner 1 · 1/2 in hole 1 in NOT DRILLED The floor (except the stud holes) and the lid. Body depth drawn 3.4 in, a guess: every hole is set 1 in below the rim. Slide a hole up to 1/2 in along the wall if it lands on a boss or the ledge inside.
MarkWhat passesGlandHoleCenter

Rules for this box

Parts not bought, or to check

ItemWhat the documents sayWhose

Decisions that shape the build

DecisionWhy it matters hereTrackedWhose

Other open items

Names used: Electronics plan = Electronics and Wiring Plan v10.3 · Compute Bay = Compute Bay Housing and Wiring Plan v10.3 · BOM = Bill of Materials v10.3 · Pending = Pending Amendments v10.4 · Box Wiring Sheet = Box Wiring Sheets v10.3. Where a guide lags a Pending item, Pending wins.