Iridium to Pi wiring

Each RockBLOCK talks to its Pi over its own USB cable, through a USB isolator at the Pi end. The red wire of the cable is moved to the Mean Well, so the modem never takes power from USB. Same for Iridium A (Pi A) and Iridium B (Pi B).

Drawn2026-10-15, rev 3
Where writtenPending Amendments, Iridium to Pi wiring
SheetUS letter, landscape
IRIDIUM BOX (one for A, one for B)AT THE PIRockBLOCK 9603pin 7 (on/off): no wire,so always onSmall plug of the RockBLOCKcable, 8 in of its wirescoax out to the lightning stub, then the antenna2-way leverYOGND3-way leveryelloworangeredblackshort blackMean WellDDR-15G-5: 24 V to 5 V−V+V24 V in: Iridium A from its own 5 A breaker,Iridium B from the backup battery boardblack goes over the red;they do not touchtapeRest of the RockBLOCK cable(the USB end), out to the Pi.Its red: cut short and taped.Brown or green wires at the cut(if any): cut short and tape.USB plugwith the USB toserial chip insideend of the RockBLOCK cable(an FTDI chip, molded in the plug)DSD TECHUSB isolatorSH-G01APi A: its2nd USB portPi B: a portThe isolator is where the lightningpath stops. Everything to its left(cable, modem, Mean Well output) isthe modem side; everything to itsright is the Pi side.Cable too short? A USB extension goesbetween the isolator and the Pi, neverbetween the cable and the isolator.The modem is powered by the Mean Well.USB carries only data, plus a littlepower for the chip in the USB plug.

Every join in the Iridium box

Wire from the small plugGoes to
yellow2-way lever connector Y, with the yellow of the rest of the cable
orange2-way lever connector O, with the orange of the rest of the cable
black3-way GND lever connector, with the black of the rest of the cable and a short black wire to the Mean Well −V
redthe Mean Well +V screw

The red of the rest of the cable: cut short, taped, not connected to anything. The Mean Well's +Vin and −Vin take the 24 V pair: Iridium A from its own 5 A breaker on the main bus board, Iridium B from the backup battery board.

At the Pi

The cable's USB plug goes into the DSD TECH USB isolator. The isolator plugs into Pi A's second USB port (Iridium A; Mike, 2026-10-20, so a hung hub cannot cut it off) or a USB port on Pi B (Iridium B). The cable reaches the Pi A box or the Pi B box through a split gland, like the battery watchman's USB lead, because the plug will not pass a plain gland.

Steps

  1. Cut the RockBLOCK cable 8 in from the small plug. Keep both pieces.
  2. Strip the four wires on each side of the cut 1/2 in. Twist each and fold it back on itself so it is thicker. If brown or green wires show on the USB side, cut them short and tape them.
  3. Push the long piece's cut end in through a gland of the Iridium box.
  4. Join yellow to yellow and orange to orange in two 2-way lever connectors. Black, black and a short black wire in one 3-way. Short black wire to the Mean Well −V screw. Small plug's red to the Mean Well +V screw. Long piece's red: cut short and tape.
  5. Plug the small plug into the RockBLOCK.
  6. At the Pi: USB plug into the isolator, isolator into Pi A's second USB port (A) or Pi B.

Good to know

  1. The USB plug on the end of the RockBLOCK cable has a USB to serial chip molded inside it. That chip turns the modem's serial data into USB; no other converter is needed.
  2. The modem runs on the Mean Well, so the isolator's 400 mA limit does not matter: it only powers the chip in the USB plug.
  3. Never put the USB plug straight into the Pi or the hub without the isolator: that ties the Pi to the lightning copper through the antenna cable's shield.
  4. Parts: one DSD TECH isolator on hand; one to buy for Iridium B.
  5. The cable's length is not known; FTDI's standard cable is about 6 ft (Claude's reading). If it is short, a USB extension goes on the Pi side of the isolator.
  6. Software: the modem shows up as a USB serial port; it talks at 19,200 baud.