# Hydrophone cable through the hull: options (2026-10-03, redone)

**Decided 2026-10-03 (Mike: "yes, go with the gland and plug change"): way A,** the stainless cable gland plus Aquarian's slide-out XLR pins. Written into the guides the same day (Science Payload Strategy 5 is the home; Build Guide 2, Bottom Painting Guide Step 0, Design Decisions R-10.2B, BOM 15.11) and the order tracker. This replaces the first version of this file (same day), which picked a plug and socket at the hull; that version is in git history. Drawing of A and B side by side: `Reference/Hydrophone Hull Passthrough 2026-10-03.png` (script `_make_Hydrophone_Hull_Passthrough_2026-10-03.py`).

## The job

- Hydrophone: Aquarian S1eX, bought on eBay 2026-09-21. The element is tiny: 0.47 in across, 1.7 in long (12 x 43 mm), anodized aluminum and polyurethane (Aquarian S1 datasheet).
- Cable: Aquarian CA-70, 0.18 in (4.5 mm), polyether urethane jacket, two 26 AWG wires plus a spiral shield, Kevlar yarns. The dry end has a Neutrik NC3MXX XLR plug: pin 1 shield, pin 2 white, pin 3 red. Aquarian: a shield on pin 2 or 3 can damage the hydrophone.
- Where: the fin station, starboard, middle third of the waterline length, 12 in above the bottom of the keel, about 2-1/2 ft below the waterline. Water pressure there is about 1.1 psi. It is the third new hole below the waterline, cut before the barrier coat (Build Guide 2; Science Payload Strategy 5). The guides say "a small potted pass-through", which can never come out.
- Mike's rules (2026-10-03): it must come out at haul-out to service the hydrophone; no nylon or other plastic fitting below the waterline; no 1 in through-hull for this cable; bed it in 5200.

## Short answer

**Way A.** Put a small 316 stainless cable gland in the hull, bedded in 5200, with its cap inside the boat. (A gland is a screw-in fitting: tightening its cap squeezes rubber round the cable.) Have Aquarian change the S1eX's XLR plug so its three pins slide out by hand. At haul-out: take the plug apart inside, by hand, loosen the cap, and pull the hydrophone and cable out from outside. Refit the same way. Nothing is cut or soldered, and the hydrophone's own cable stays whole.

Why it beats the plug and socket at the hull (way B):

- **Aquarian already does this, for this job.** Their sheet on the change (NC3MXX-MOD): it "may be beneficial for other hydrophones with XLR output where the cable is routed through a conduit, waterproof cable gland or other similar orifice. Aquarian will charge a small additional fee to make this modification." It is standard on their panel-mount S1eX.
- **No cutting.** Way B cuts the hydrophone's cable once and glues a plug on it. Aquarian's warranty counts "torn or cut cables" as abuse.
- **The fin can be glued on for good.** With a plug at the hull, the fin has to come off or open at every haul-out to reach the plug.
- **Simpler and cheaper.** About $45 in parts plus Aquarian's fee, against about $245 to do way B yourself (it also needs a drill press and a Dremel).
- What a failure looks like: a gland weep shows in the bilge, the pumps handle it, and the cap gets tightened at the next haul-out; the hydrophone keeps working. In way B the socket keeps the sea out, but a leak at the plug quietly kills the hydrophone.

## Way A parts

| Part | Price | Where |
|---|---|---|
| Jacob WADI heat cable gland K257-1012-00: M12 x 1.5, body and cap 316L stainless, seal and O-ring FKM (Viton) rubber, **no plastic parts**. Cable 3 to 8 mm; the removable inner ring makes it 3 to 5 mm (0.12 to 0.20 in), which grips our 4.5 mm well. Thread 0.26 in (6.5 mm). Wrench 16 mm, cap and body | $26.72, 56 in stock (checked 2026-10-03) | DigiKey: https://www.digikey.com/en/products/result?keywords=K257-1012-00 |
| Aquarian NC3MXX-MOD on the S1eX's XLR | "small additional fee", not listed. Aquarian says most hydrophone fixes cost $20 to $100, so likely about that (a guess) | sales@aquarianaudio.com, 360-299-0372. Email drafted below |
| M12 x 1.5 tap with its 10.5 mm drill (the 60-piece set on hand has only M12 x 1.75, checked 2026-10-05) | $16.85, in stock | Amazon, Drill America: https://www.amazon.com/dp/B0CTWJDM29 |
| 3M 5200, thickened epoxy, Tef-Gel | on hand | |

The Jacob is rated IP66, IP67 and IP69: tested to about 3.3 ft (1 m) for 30 minutes and against hot washdown jets, not for long immersion. Every 316 gland with an IP68 (long immersion) rating whose parts list we could read has a plastic clamp ring inside: polyamide (nylon) in the Lapp SKINTOP INOX, Hummel HSK-INOX and Cembre MAXIinox, PVDF in one Hummel. My opinion: at 1.1 psi the Jacob, all metal and Viton, is the better fit for your no-plastic rule. The rating tests are 30 minutes either way (Hummel's IP68 is 10 bar, about 330 ft, for 30 minutes); none promises two years. At 2-1/2 ft the push is about 1.1 psi, less than the Jacob's 3.3 ft test. Over two years what decides it is the rubber staying squeezed on the cable, the same for every gland and tested by no rating. The week-long water test (Fitting it, step 2) settles it for this gland. If you would rather have the IP68 rating: Lapp SKINTOP INOX 53806739, 316L, M12, cable 4 to 7 mm, IP68 at 10 bar, $68.26 at DigiKey, 104 in stock (https://www.digikey.com/en/products/result?keywords=53806739); nylon ring inside, silicone seal.

No 316 gland on Amazon could be confirmed as 316: listings that say 316 turn out to be 304, give no grade, or contradict themselves. One (XMADMEISA "316 Stainless Steel Cable Glands", M12 6-pack, $32.63, Amazon B0HK2S86NS, likely ships from China, Oct 20 to 30) says "made from SUS316" with no other details to check. McMaster's stainless cord grips are 303 stainless with nickel-plated brass locknuts, not 316.

## Fitting it

1. **Pick the spot from inside first** (see the check below). The cap must be reachable with two 16 mm wrenches, on bare hull glass (grind any liner back, as for the intake).
2. **Bench test first:** once Aquarian has changed the plug, push the taped pins through the gland on the bench to be sure they pass. Then leak test it (Mike asked 2026-10-03 whether the IP67 rating is a problem): tap a PVC cap M12 x 1.5, thread the gland in from the outside of the cap (plumber's tape on the threads), glue the cap on the bottom of a 3 ft piece of 1 in or bigger PVC pipe, run the hydrophone and cable through so the hydrophone sits in the pipe, fill the pipe with water and leave it a week over a dry paper towel. That is the real depth and the real direction (water on the thread side, cap dry). The rating is a 30-minute test; this is a week.
3. Drill a 3/4 in hole. Tape the outside, fill the hole with thickened epoxy and let it cure. This seals the raw edge of the hull glass and gives the thread something solid to bite.
4. Drill 10.5 mm through the epoxy and tap it M12 x 1.5 from inside. (No nut: the hull is likely 3/8 to 1/2 in thick, and the gland's thread is only 1/4 in long.) If the inside face is curved, make a flat seat for the gland with a dab of thickened epoxy.
5. Screw the gland body in from inside with 5200 on the threads and under the hex, its O-ring in place. Fill the threads fully so no seawater sits in them. Wipe the squeeze-out. A week to cure before launch.
6. Feed the cable in from outside, pins taped together, through the fin's tube and the gland. Rebuild the XLR. Tighten the cap by hand, then about a half turn with a wrench while holding the body with the other. Tef-Gel on the cap threads (stainless on stainless can seize).
7. Clip the cable inside within 6 in of the gland, then run it uphill to above the waterline before it goes anywhere else.

The fin: give it a smooth tube for the cable, 5/16 in inside or more, from the hull hole to the tip, gentle bends only, so the cable and taped pins slide through. The fin is still a concept drawing, so this costs nothing now.

## At haul-out

1. Inside: unscrew the XLR's back end, slide the parts off, tape the three pins together.
2. Loosen the gland cap, holding the body with a second wrench.
3. Outside: pull the hydrophone; cable and pins slide out through the gland and the fin.
4. Rinse the pins in fresh water and dry them (Aquarian: seawater corrodes them). Check the solder joints at the pins; Aquarian warns they can break with bending.
5. Refit in reverse. Let the seal grip a fresh spot on the jacket, an inch along, if the tether length allows. If the seal ever weeps for good, the cap and seal from a new gland of the same make fit the body already in the hull.
6. If the boat goes back in without the hydrophone, tighten the gland on a 3/16 in stainless rod stub as a plug.

## Check before drilling: where the hole comes out inside

At 12 in above the bottom of the keel the inside may not be open bilge:

- Practical Sailor on the 25D: the lead is in "a hollow keel molding, with voids... filled with polyester slurry", "heavily glassed over on the inside"; "a full molded hull liner"; bilge access "only through a small trap in the main cabin sole."
- Cape Dory owners (forum summaries, not read in full): bilge sides about 1/2 in thick or less; water found trapped between the lead and the slurry cap; the 25D bilge is deep and narrow.
- 2,050 lb of lead is about 5,000 cubic inches. Spread 5 to 7 in wide over 6 to 8 ft, that is 7 to 14 in tall plus its cap (a guess). So a hole 12 in above the keel bottom could open into the lead, the cap or a wet pocket.
- The Build Guide (3.6) says the sump floor is the top of the ballast. The battery box sits on foam in the trough.

So: measure down from the deck edge to the station outside, and down from the deck to the sump floor inside, at the same spot fore and aft. The hole must come out above the sump floor, clear of the battery box and its foam, with room for the wrenches. If it would not, raise the fin until it does. Both ways A and B need this; way B needs it only to fit the socket, way A at every haul-out.

## Way B: plug and socket at the hull (Blue Trail Cobalt)

Blue Trail Engineering, Longmont, Colorado; order direct, not on Amazon. Prices from their September 2026 price list and store, all in stock:

| Part | Price |
|---|---|
| COB-1130-SS 3-pin socket (bulkhead connector): 316 shell, PEEK insert, M10 x 1.5, 10 mm hole, 0.71 in flange with a face O-ring, 0.63 in shank (nut grips a wall 0.20 to 0.43 in thick, so a 1/2 in hull needs a counterbore or tapped pad), 12 in of 18 AWG leads (unshielded, untwisted) | $42 |
| COB-3130-SS 3-pin plug kit (for cable up to 6 mm) | $25 |
| COB-3230 termination tool (required) | $45 |
| COB-3310 mold for 4.2 to 6.0 mm cable | $2 |
| COB-1002 dummy plug and COB-1001 locking sleeve to hold it | $6 + $7 |
| 3M DP420 epoxy, the one Blue Trail tested (Amazon B07FQQGP96) and its EPX gun (Amazon B07VFKX33P) | $46.88 + $71.83 |

About $245 all in, plus a drill press and a Dremel for the plug job. Or Blue Trail or Aquarian fits the plug: Blue Trail offers "installation of Cobalt connectors on customer-supplied cables", and Aquarian "often" builds hydrophones with Cobalt plugs; neither lists a price. Rated 600 m (1,970 ft), 500 plug-ins; plug and unplug only out of the water. The locking sleeve that holds the plug in, and the dummy plug, are acetal plastic. No months-to-years ocean reports found; the maker says it withstands "long-term use in seawater". How it goes: cut the cable where it reaches the socket, fit the plug on the outside piece, solder the inside piece (XLR still on) to the socket's leads.

## Way C: a small tube up past the waterline

The fishing and research practice for transducers that must come out: Simrad tells installers to run a pipe "unbroken and watertight from the transducer to above the water line", which makes it "easier at a later stage to replace the transducer" and "the risk of flooding is greatly reduced"; research ships run cables down pipes to above the waterline; one steel yacht has a stainless pipe welded into the keel with a cable gland on top. Here: a small fiberglass (G10) tube glassed through the hull at the station and up the inside to above the waterline, with a cheap gland on its top end. With Aquarian's slide-out pins the tube can be small, about 3/8 in inside, so the hole stays small. Then nothing rubber or stainless is under water, and the cable pulls out the same way as in A. Catch: it needs a straight path of about 3 to 3-1/2 ft inside the hull from the station to above the waterline, through the molded liner, with the battery box in the trough. Worth it only if that path exists. The top gland still matters in a knockdown.

## Ruled out, and why

- **Blue Robotics WetLink:** fits exactly (4.5 mm, $13) but 7075 aluminum, next to copper paint; Blue Robotics says reuse at most 3 times, new seal each time.
- **SubConn Micro Circular** (MacArtney): plug-in underwater, bodies in 316, titanium or leaded brass (the brass loses zinc in seawater). The cable end comes only molded on its own rubber cable, so it needs a splice in the water or a custom build by Aquarian. MCBH3MSS socket $46.75 (out of stock), MCIL3F on 1.6 ft of cable $169.53, titanium unpriced. Ocean observatories report connector corrosion after a year at sea. A Chinese copy is $62 a set on Alibaba, quality unknown.
- **Any gland at the hull with the XLR left on:** the plug is 0.77 in across, so the hole must be about 1 in (Roxtec RS 25 in 316, two-piece seal, about 68 pounds sterling in the UK, no US price found, needs a sleeve); the other split glands found are plastic.
- **Potting or sealant only** (the guides' "potted pass-through", ROVMaker's $4.90 epoxy-filled bolt, Blu-Sub's potted penetrator): cannot come out. A Blue Robotics engineer on a hydrophone install: "Potting in general is not a robust or reliable solution... even if it passes a vacuum test, it may fail later!"
- **Nylon glands, 303 or 304 stainless glands, LEMO W series (304L):** nylon by Mike's rule; 303 and 304 pit below the waterline.
- **Blu-Sub Deep-Sea M10 gland, 316:** none of its seal sizes fits 4.5 mm cable without building the cable up with heat shrink.
- **Forespar 1 in Marelon through-hull** (two on hand): far too big, plastic, and not removable.
- **Marine-store cable seals** (Seaview, Cable Clam, Scanstrut): above the waterline only. **Navy stuffing tubes:** brass or steel, made to weld into steel.
- **Running the cable up the outside** to enter above the waterline: crosses the waterline in the open, takes hits, strums and drags.

## Risks worth knowing

- **Will it go two years with no leak?** (Mike, 2026-10-03.) Claude's guess: about 9 chances in 10 of no weep at all; not a promise. The push is tiny (1.1 psi) and a tight, checked rubber seal does not mind time at that pressure (inferred). The main doubt is the 316 itself in the still water inside the fin root (next point), not the rubber. A leak would most likely be a slow weep, caught by the bilge sensors. Worst case, the whole gland gone: Claude's arithmetic gives about 3 to 5 gal/min through the hole, against pumps rated 3.7 and 5 gal/min, so the two together keep up. Cheap extras: the week-long water test (Fitting it, step 2), and a paint-pen line across the cap and body to show at a glance if the cap ever turned.
- **316 in stagnant seawater** can pit in crevices, such as threads bedded below the waterline (Steve D'Antonio: avoid stainless "where it may be exposed to stagnant, oxygen-depleted water, especially below the waterline"). Applies to A and B alike. Filling the threads with 5200 leaves no water in them. For two years at this size I expect staining at worst (my opinion); look at it at each haul-out. Way C avoids it.
- **Water inside the cable:** a gland seals only the outside of the jacket. If the jacket is ever cut outside, water can creep along inside it. Running the cable uphill above the waterline right after the gland stops it reaching anything.
- **Cable damage** is Aquarian's second most common failure ("animals will attack the cable"); they advise a hard conduit for long deployments. The fin's tube is that conduit.
- The fitting stays unbonded, like the other science fittings (Lightning Guide step 2).

## Done when decided (2026-10-03)

- Pending Amendments: the question is closed (written into the v10.1 guides); the fin station item still carries the check from inside.
- Guides: Science Payload Strategy 5 (the gland, the plug change, the checks, fitting and haul-out steps), Build Guide 2 and 12, Bottom Painting Guide Step 0, Design Decisions R-10.2B (the why), BOM 15.11 (the gland and tap kit, $44 to buy; Aquarian's fee not listed).
- Order tracker: the gland, the tap kit and Aquarian's plug change on the Buy list and Parts tabs; emailing Aquarian on the Do next tab; the hydrophone row now links Aquarian's S1 page instead of the MOTU M2's Amazon page.

## Email to Aquarian (ready to send for way A)

To: sales@aquarianaudio.com
Subject: NC3MXX-MOD on an S1eX I already have

Hello,
I have an S1eX (standard body, CA-70 cable, XLR plug). Its cable will pass through a stainless cable gland in a boat hull, and I want to pull it out at haul-outs without cutting it, so I would like your NC3MXX-MOD done on its XLR.
1. What is the fee and the turnaround?
2. Should I send the whole hydrophone, or can you send a modified plug (holder, pins, bushing) for me to fit?
3. It will trail behind a fin about 2-1/2 ft below the waterline for about two years. Any advice on the anodized body next to copper bottom paint?
Thanks,
Mike

## Sources

- Aquarian S1 datasheet (rev 1, 7/1/2025): https://www.aquarianaudio.com/AqAudDocs/S1_datasheet.pdf
- Aquarian NC3MXX-MOD assembly sheet: https://www.aquarianaudio.com/AqAudDocs/NC3_MXX_MOD_Assembly.pdf
- Aquarian panel mounting sheet: https://www.aquarianaudio.com/AqAudDocs/M10_panel_mounting.pdf
- Aquarian S1 page and CA-70 page: https://www.aquarianaudio.com/s1-hydrophone.html, https://www.aquarianaudio.com/ca-70-hydrophone-cable.html
- Jacob WADI heat datasheet: https://www.jacob-gmbh.de/fileadmin/products/orig/S127_Datasheet_WADI_cable_gland_K257-1xxx-zz.pdf
- Hummel HSK-INOX via Sealcon (quote only): https://www.sealconusa.com/product/cd12ma-6s/
- Blue Trail Cobalt: https://www.bluetrailengineering.com/cobalt; potting note: https://www.bluetrailengineering.com/_files/ugd/e4c7c5_dfb35d89f9324eb7ab14b153a28fd381.pdf
- SubConn Micro Circular datasheet: https://cdn.macartney.com/media/2jdjruxm/micro_circular_2_3_4_contacts.pdf
- Blue Robotics WetLink: https://bluerobotics.com/store/cables-connectors/penetrators/wlp-vp/; potting advice: https://discuss.bluerobotics.com/t/need-advice-to-install-hydrophone-through-penetrator/20639
- Roxtec RS seal: https://cdn.content-publisher.roxtec.com/solutions/solution:1113/en-us/Roxtec%20RS%20seal_imperial.pdf
- Simrad ES38-12 installation manual: https://manualzilla.com/doc/7297765/simrad-es38-12---installation-rev-a-installation-manual?page=26
- UNOLS in-water transducer removal: https://www.unols.org/sites/default/files/InWaterTransducerRemoval.pdf
- Practical Sailor, Cape Dory 25D: https://www.practical-sailor.com/?p=82323
- Cape Dory forum threads (summaries only): https://capedory.org/forums/viewtopic.php?p=140991, https://capedory.org/forums/viewtopic.php?p=219861
- Stainless below the waterline (D'Antonio): https://www.cruisingworld.com/monthly-maintenance-steel-your-resolve/
- Ocean observatory connector corrosion: https://eos.org/science-updates/deep-trouble-common-problems-for-ocean-observatories
