# Box parts check, every box (2026-10-14)

Mike asked (2026-10-14): "Please review ALL boxes and see what parts are missing. Seems like every time we start to assemble a box we are waiting on parts."

Checked against: the v10.2 guides (Electronics and Wiring Plan Appendix A and secs 6 to 8, Compute Bay Plan, Battery Box Guide, Transom Drogue Box Guide, Wing Power System, Wire and Cable Buy List, BOM), the Box Wiring Sheets as of 2026-10-14, the Oct 14 drawings (VESC A box, capacitor hookup, lightning detector), Pending Amendments v10.3 through item 426 (this check is item 427), and the order tracker (`BOM v10.5 Order Status.xlsx`, every tab, as of Oct 14 afternoon).

**The short answer.** Most of the big parts are bought. The waits come from three kinds of small things: (1) about 15 small parts nobody bought, because no guide ever counted them (wire, lugs, splices, jumpers, fuse holders, vents); (2) about 30 parts that shipped with no delivery mail, so nobody knows if they are on the shelf; (3) about 15 parts that cannot be bought until a choice is made (a box size, a plug type, a fuse size).

How to read the status words: **BUY** nobody has ordered it. **SHELF** it shipped but no delivery mail came, so look for it. **COUNT** we have some, but nobody has counted against the need. **COMING** ordered, not here. **PICK** a choice is needed before it can be bought.

---

## 1. Buy now: nothing left to decide

| Part | For | Why it is short | Link |
|---|---|---|---|
| Wing box: TICONN IP67 ABS box, 5.9 x 5.9 x 3.5 in, with mounting plate | Wing box (A17) | Picked Oct 12 (Pending, "wing box material"), never ordered. Same box as the two Iridium boxes. That the three surge modules, the TVS and the fuse fit is a guess | Amazon B0B87THLGC, $19.99 on Oct 9 |
| Superbat SO-239 to BNC jumper, 1 ft, 2-pack | dAISy, USB hub box | Already on the Buy list (Pending 422) | Amazon B087Q49GS1, $12.99 |
| FTDI USB-RS232-WE-1800-BT-0.0 cable | SBE 45, USB hub box | Already on the Buy list (Pending 424) | Amazon B00DEED3GM, $23.00 |
| Altelix PG25 4-port split gland | BMS box, the USB lead | Already on the Buy list (Pending 423) | Amazon B0GYT3ZMDL, $6.99 |
| Shielded Cat6, all copper, 25 ft | Wing box to USB hub box | Marked ordered Oct 7, but no order mail. Skip only if shielded Cat6 on hand has no other job | Amazon B077H5LL5N, $14.98 |
| 16/2 tinned duplex, 100 ft, **two rolls** | Bus board lines, the six switched runs aft, the horn, the bow lantern | Need about 220 to 260 ft (100 bus board lines, 120 switched runs, about 15 horn, about 25 bow lantern; run lengths are guesses until measured). 100 ft on hand. The second roll was marked ordered Oct 7, but no order mail | Amazon B0DDQ4HJJC, about $54 each |
| SMA female bulkhead to SMA male, RG316, 3.3 ft, 2-pack | GPS A and GPS B, wall to the NEO-7M board inside each Pi box | Two inside leads needed, one SMA male-male cable on record (Aug 1). This part is the bulkhead and the lead in one, so it replaces both | Amazon B07Z343VH4, $9.99 (Wire List D1) |
| 30 AWG tinned copper wire, a small spool | The 22 fuse links on the battery tap wires (18) and the shunt sense wires (4) | Wire List E4 says make them from 30 AWG tap wire, "no part to buy", but no 30 AWG copper wire was ever bought. The only 30 AWG on hand is nichrome, which does not substitute (E4) | [Amazon search](https://www.amazon.com/s?k=30+AWG+tinned+copper+wire+spool) |
| 3/8 in ring lugs: two for 8 AWG, two for 12 AWG | VESC A posts: the Flipsky's own 8 AWG leads and the two 12 AWG leads off the WAGO lever nuts (Pending 417) | None on record. The 3/8 in lugs on hand are 6 AWG and 2 AWG; the 12 to 10 AWG heat-shrink rings on hand are #10 stud | 8 AWG: Crimp Supply 8 Ga heat-shrink ring, 3/8 in stud, 10-pack, Amazon B00NVCCAFW (or MVP 3M heat-shrink 10-pack, B084NJYGCK). 12 AWG: Ancor 12-10 AWG heat-shrink ring, 3/8 in stud (yellow), Amazon B073PGZC5V, or the Ancor 25-pack 312625, B07G87368C. Prices not checked (Amazon pages would not load, 2026-10-14) |
| Neutral-cure silicone, small tube | Gluing the four capacitors and two WAGOs to the VESC box floor (Pending 417) | None on record. The Berkland 4000 and 3M 5200 on hand are not silicone | [Amazon search](https://www.amazon.com/s?k=neutral+cure+silicone+sealant+small+tube) |
| M4 316 pan-head screws, about 3/8 in, and M4 316 flat washers | The four cord puller motors (Transom Drogue Box Guide 6) | Only black 304 M4 screws and an alloy kit on record (Pending 276) | [Amazon search](https://www.amazon.com/s?k=M4+316+stainless+pan+head+machine+screw) |
| DIN rail, 35 mm (1.4 in), one length to cut | Switch box side wall (A6a) | Already a BUY row on the tracker Parts tab. The rails on hand are 4 in VAMRONE pieces and the Erayco kit's 8 in rail, which the central node and others also need | [Amazon search](https://www.amazon.com/s?k=35mm+DIN+rail+aluminum+1+meter) |
| Insulating boots, M8 posts, red and black | Dyness emergency battery | Already on the Buy list. Or tape the posts | [Amazon search](https://www.amazon.com/s?k=battery+terminal+boot+M8+red+black) |

Buy after the count in section 3, if short: sealed inline fuse holders (about 4 short), membrane vents (3 to 6 short), heat-shrink crimp butt splices 22 to 18 AWG (17 needed), WAGO 221-415 lever nuts (8 needed), N2K Micro-C 2 m cords (about 3 short).

---

## 2. Already bought, still coming

| Part | Box | Due |
|---|---|---|
| Mean Well DDR-60L-5 | Pi A | Oct 13 to 15 |
| Pi GPIO screw-terminal boards x2 | Pi A and Pi B (job not yet written) | Oct 14 to 16 |
| Shunts 300 A and 100 A | Main bus board | Oct 6 to 16 |
| WAGO 221-415 lever nuts (count not logged) | VESC A capacitors; battery box probes | Ordered Oct 14 |
| Mean Well DDR-15G-5 x2 and TICONN 5.9 in boxes x2 | Iridium A and B | Ordered Oct 9, no ship mail yet |
| Taidacent RS-12V/2S x3 | Wing box (one), two with no job | Oct 21 or later |
| Rion HC2549 slip ring | Wing | About Oct 20 |
| Camera port window | Camera port | Oct 19 to 27 |
| Sea-Bird SBE 45 | Wet lab | About Oct 26 |
| Thomson trim actuator | Wing | Was about Oct 7; no mail |
| Kamoer dosing pumps | Wet lab | Oct 2 to 14 |

---

## 3. Look on the shelf, or count

**Shipped, no delivery mail (find it):**

- Pi A: the 4 TB SSD; the two BNO085 motion boards (three shipped Sep 10, one is Pi B's); the Altelix 4-port and 5-port split glands (the drawings say on hand, the tracker still says coming).
- Pi B, central node, Release Node B: the Klnuoxj 24 to 5 V converters (two 4-packs, three needed).
- Central node: the second HiLetgo 8-channel relay module.
- USB hub box: the Waveshare 2-channel RS-485 reader; the SDI-12 adapter.
- BMS box: the SBMS0 WiFi/USB board (needed for the battery percentage); the Winford BRK2X6 breakout boards.
- Battery box: the second 50-pack of M6 cone washers (64 needed, 50 confirmed).
- Wing box: the two Taidacent modules of Sep 26.
- Wing tip: the WitMotion HWT905 compass; the Calypso wind meters (both).
- Main bus board: the two battery bus surge modules (probably the China box of Oct 9); the 250 A MEGA fuse (Sep 7).
- VESC A: the Metri-Pack 150 plug pair for the motor sensor.
- Drogue boxes: the VEVOR fiberglass box (due Oct 2); the PKS Dacron tape; the Auveco end caps.
- Wet lab: the pressure transducer; the DO sensor; valve 1 (which size came).
- Others: the em-trak B921; the hydrophone hull gland; the DIN end stops 50-pack; the second RockBLOCK (one was shipped to Gunnison, CO).

**Counts nobody has done (count, then buy only the shortfall):**

| What | Need | On record | Note |
|---|---|---|---|
| Sealed inline fuse holders | About 13: 7 at the bus board, then Pi A's hub lead 3 A, wing box 5 A, wing tip 1 A, horn 5 A, two post feeds (the hub box's 24 V fuse is gone, Pending 426) | 9 | About 4 short (Pending 401 p) |
| Membrane vents, M12 | About 15: 11 boxes in Appendix A, the battery box, plus the hub box, wing box and light driver box if plastic | 9 (an 8-pack and one breather screw) | 3 to 6 short |
| Cable glands | About 120 boat wide; PG16 x7 (VESC 5, battery mains 2); PG11 13 to 17; PG13.5 6 (now that the battery tap cables get their own glands, Pending 411) | Two 25-packs in the order log, plus the 100-piece kit and the Glarks 22-piece kit Mike reported Sep 6 | Count by size, PG16 and PG11 first |
| DIN rail fuse holders | 8: four cord pullers, four on the emergency bank strip (Pi B, Iridium B, the 75/10, the Orion-Tr) | One MECCANIXITY order (Oct 10), count unknown | |
| Heat-shrink crimp butt splices, 22 to 18 AWG (not the solder-seal kind) | 17: 8 at the VESC capacitors, 9 for the JK balancer harness. If short: Ancor 22-18 AWG heat shrink butt connectors, 100-pack, Amazon B00JLKPP5A (crimp, tinned, glue-lined; price not checked). The two ends that take two thin harness wires (W0, W8) should still fit the 22-18 barrel (inferred) | One hidden-item buy Sep 13, type unknown; the Kuject kit is solder-seal, which the no-solder rule rules out | |
| WAGO 221-415 | 8: 2 at the VESC, 6 joining the pack probes in the battery box (Pending 411) | Oct 14 order, count not logged. The generic lever connectors on hand (XHF, SUTETLW) are not WAGO | |
| N2K Micro-C 2 m cords (cut for drops) | About 11 | 8 in the order log; Mike says more on the shelf | Check each jacket fits a PG7 (1/4 in max) |
| DIN screw terminals | About 170 across the central node, aft junction, transom box and Release Node B (a rough guess) | Erayco 20, MELIFE 30, two Aug 16 kits of unknown size | |
| TVS diode bag | About 14 1.5KE33CA | One 20-pack | Check the bag is 1.5KE33CA, not the 1N5408 flybacks |
| Iridium LMR-240 jumpers | 4 (both sides of each stub) | 2 KMR240 in the order log; Mike reported 4 on Sep 6 | |
| 18/4 tinned | About 62 ft (trunks, tails, wing actuator, channels 9 and 10) | One 50 ft roll confirmed, maybe a second (Sep 5) | Mike said Oct 7 there is enough |
| 12-pin ribbon | One, female both ends, about 8 in | MECCANIXITY 6 in (Oct 6) | Read both plugs: two rows of 6 at 0.1 in? 6 in is enough if the Winford board sits within about 5 in of the SBMS0 |
| USB leads | The hub's lead and the CAN adapter's lead to Pi A; mini USB for the dAISy; the SDI-12 adapter's; the SBMS0's (long run from the battery box) | Only four 6 in extensions on record | Check what came in each box |
| Berkland 4000 | 2 | 1 | |
| G10 1/8 in sheet | Two compute box plates | One sheet, which makes one plate | The second from the 4 mm sheet of Aug 9 (a guess) |

---

## 4. Waiting on a choice (cannot buy yet)

**Boxes not picked:** the USB hub box (the two aluminum boxes on hand are probably too small; a guess); the wing tip box; the PoE light driver's dry box; the second drogue box (the TICONN box of Oct 3 is ABS, and the guide says size up in fiberglass only); the wet lab's reader and switch board and its box (now laid out: `Reference/Wet Lab Box 2026-10-14`, Pending 428; one NUCLEO-G431KB to buy); the lightning detector mini-box (the Zulkit project boxes on hand probably do).

**Plugs and wiring not named:**

- Slip ring: Deutsch DT plug halves, pins, sockets, seals and the crimp tool are on no order. The pin count waits on how the one 24 V pair feeds both wing cables, and DT pins may be too big for 22 AWG (then the smaller DTM series).
- The hull cables from the ring, the deck gland they pass, and the C5 cable up the trailing edge (now about 13 to 15 ft if it runs tip to ring with no joins; a guess).
- VESC A: the plug for the PPM kill pin (Pending 418), the plug for the motor temperature pins, and the shorted switch plug. Plug types are not written; read them off the board. Also no potting compound for the sensor harness, and the cooling plate is not sized.
- Iridium boxes: a premade coax jumper's plug will not pass a PG7. The same split-gland answer as the USB leads (Pending 423) may serve.
- Pi A and Pi B: the 5 V lead from the converter into the carrier board.
- Drogue boxes: the crimps joining nichrome to the copper leads, the lead wire gauge, and the potted pass-throughs (four in all).
- Aft junction: the post lights cable (4-core), the post feed fuses (size and holder), the bilge and encoder leads.
- Release Node B: the fire pair cable to each drogue box, and its gland (A15 says PG7, A16 says PG9 for the same job).

**Small parts with no pick:**

- A 5 V surge diode (TVS) across the lightning detector lead inside the Pi B box (Pending 420). The 1.5KE33CA is the wrong voltage here.
- The pull-down resistor value for the central node's output expander, and the 1-wire pull-ups (the resistor kit on hand has the usual values).
- Fuse sizes on the emergency bank strip (Pi B, Iridium B, the 75/10).
- Starlink Mini mount or cover (Pending 373), and its 24 V lead.
- Network switch box: right-angle Ethernet plugs (read the direction off the switch); the surge board near the deck (the board, a small tinned bus bar, the five ground leads) and the five Cat6 runs down to the switch box (measure first).

**Docs disagree, Mike's call:**

- Release trunks: three cables (one 14/4 fire, two 18/4 puller) but two PG11 glands, and the plan bans two release cables in one gland. A third gland, or a new core plan.
- The INA226 meter on Pi A's feed: the Compute Bay Plan and Sheet A1 keep it; the tracker and BOM say none on the boat (the three went back Sep 8). Claude's opinion: strike it.
- Pi B's GPS wall fitting is a metal SMA bulkhead, against the rule that nothing metal touches Pi B's wall.
- The battery box's fuse links: the BOM prices nine, the guide needs 22.
- Drogue strap-hole liners (PTFE tube) and the cord tube both went back Oct 1 to 2; still wanted? The cord tube's size differs between the guide (2 mm ID x 1/8 in OD, 20 ft) and the tracker (2 x 4 mm, 8 ft).
- Drogue U-bolt collars: keep the carbon steel ones or buy stainless (Pending 408).

---

## 5. Box by box, what holds it up

| Box | Holds up assembly |
|---|---|
| Pi A (A1) | Mean Well (coming); 4 TB SSD and IMUs (shelf); SMA lead to GPS (buy); carrier power lead (not named) |
| USB hub box (A1a) | The box itself (pick); dAISy jumper, SBE 45 cable, wing cable (buy); reader and SDI-12 adapter (shelf); USB leads (count) |
| Pi B (A2) | Klnuoxj converter and IMU (shelf); 5 V TVS for the detector lead (pick); GPS wall fitting (Mike's call); SMA lead to GPS (buy) |
| Central node (A3) | Second relay module and Klnuoxj (shelf); puller fuse holders (count); pull-down value (pick); trunk glands (Mike's call); DIN terminals (count) |
| BMS box (A4) | WiFi/USB board and Winford board (shelf); Altelix gland (buy); butt splices (count); 12-pin ribbon (read it) |
| Aft junction (A6) | Post feed fuses and holders (pick); post lights cable (pick); 16/2 (buy) |
| Switch box (A6a) | Side-wall DIN rail (buy); right-angle plugs and surge board (pick) |
| VESC A (A7) | Metri-Pack plug (shelf); WAGOs (coming); 3/8 in lugs and silicone (buy); kill and temperature plugs (pick); cooling plate (size it) |
| Battery box (A9) | 30 AWG wire for 22 fuse links (buy); M6 washers (shelf); WAGOs (coming) |
| Emergency bank (A10) | Post boots (buy); fused DIN strip holders and fuse sizes (pick) |
| Iridium A and B (A11) | Boxes and converters (coming); second RockBLOCK (shelf); LMR-240 jumpers (count); coax through the gland (pick) |
| Detector (A12) | Box (likely a Zulkit on hand); 5 V TVS (pick) |
| Release Node B (A15) | Klnuoxj (shelf); fire pair cable and gland size (pick) |
| Transom box (A16) | Trunk core plan (Mike's call) |
| Wing box (A17) | The box (buy); Taidacent modules (shelf and coming); hull cables, deck gland, DT plugs (pick) |
| Wing tip box | The box (pick); butt splices (count); 1 A fuse and holder (count) |
| Drogue boxes | Box 1 (shelf); box 2, crimps, pass-throughs, liners (pick) |
| Light driver box | The box (pick) |

---

## 6. Parts with no box yet (added 2026-10-14, Mike asked)

| Part | Where the docs leave it | Claude's view |
|---|---|---|
| Axis P1245 main unit (underwater camera) | "Dry main unit inside the boat" (Camera Port Guide step 4); no box | Needs one. Opinion: one small camera box near the port holding the main unit and the UV-C regulator below; Cat6 out on a taped bulkhead jack, the UV-C feed in on a PG7 |
| LM317 regulator and its 62 ohm resistor (camera port UV-C) | "At the port"; no box or spot written | Goes in that camera box |
| MOTU M2 (hydrophone audio) | Where it sits is open (Sheet A1a) | A desktop unit, not sealed. Either inside the USB hub box (it is about 7.6 x 4.6 x 1.8 in, so the hub box grows) or its own small dry box beside it |
| PoE Texas light driver | Bare board; dry box to buy, not picked | Already on the list |
| Lightning detector board | The tiny box is not named | A Zulkit project box on hand probably does |
| Wing tip fuse, DROK converter, splices | Tip box not picked | Already on the list |
| Starlink Mini | Mount or cover open (Pending 373) | Already on the list |
| Two CAN bus 24 to 12 V converters (YRDZXG) | At the compute multiport; no box written | Potted and sealed, so no box needed (opinion); glue to a pad |
| Main bus board, the five MPPTs, the Orion-Tr, the 75/10 | Open boards on purpose, dry and upright (Electronics plan 7.6, A10) | Fine as written |
| Wet lab parts | No box | Now the wet lab box, A18 (Pending 428) |
| No job at all | Two Pi GPIO screw-terminal boards (coming); the DROK 24 to 5 V bought for the hub box; the DSD TECH SH-G01A USB isolator; the SparkFun AS3935 (the Playing With Fusion board replaced it); one Taidacent RS-12V/2S (the other goes to the wet lab box); the Amphenol PST360 (Send back tab) | Mike to say: keep for Boat 2, or send back |

> Footnote, 2026-10-27, not part of the 2026-10-14 list. Pending 454 is decided (Mike, 2026-10-27: "pex is specced for the wing"): the wing wiring tube moves off the trailing edge. The tube is one 10 ft stick of 3/4 in PEX water pipe, 7/8 in outside. Pending 461, decided in Pending 2026-10-29, guides not yet rewritten: "DECIDED: 1/2 in PEX for the whole vertical run, root to tip" and "One 10 ft stick of 1/2 in PEX covers both lengths." The 3/4 in size in the sentence above is Pending 454 and is superseded inside Pending. The wing cable in that decision is Cat6 at 0.225 in across (stranded per Buy List C8's rule, to confirm). The mast-plate route is still a proposal. Mike's yes still needed on the whole route before the channel is cut. "C5 is still not bought" is the 2026-10-27 footnote. C5 is still not bought. The length stays a guess.
