Bilge pump wiring

Boat 1 · both pumps · a wiring map, not to scale, not placed as on the boatOct 31, 2026 · Updated 2026-11-01 · 1 page
MAIN BUS BOARD by the battery box + bar, 24 V always on Breaker 11 · 5 A end stud · pump 1 − branch bar (0 V) 16/2 up to 22 ft BACKUP BATTERY BOARD beside the Dyness + bar, backup 24 V Breaker 15 · 5 A spare spot · pump 2 BatteryProtect cuts at 30% left 1.5KE33CA across − bar (backup 0 V) 14/2, from the roll on hand PUMP 1 (primary) Whale Gulper 220, BP1554 24 V · about 1.75 A high on the glass panel − + WATER WITCH 1 · 230-24 in the sump, LOWER on the angle starts first red black tan J2 J3 J1 PUMP 2 (backup) Whale Gulper 320, BP2054 24 V · about 3.25 A high on the glass panel − + ULTIMA SWITCH · JOHNSON 36303 sealed, never touches the water HIGHER on the angle, above Water Witch 1 on about 2 in, off about 3/4 in, 3 s delay feed 0 V out J2 J3 J1 to Pi B’s side: P2 ON, P2 RUN red P1 ON black P1 RUN white, 4th: unused C4 18/4 shielded CENTRAL NODE by the battery · 15 A feed Relay ch 6 · normally open then fuse, 5 A slow-blow out on the red core: P1 ON Relay ch 12 · spare white core unused (pump 2 is on Pi B’s side) Opto board, 2 inputs input 1: black core, P1 RUN input 2: spare, 4th core unused 24 V there = pump running input common to 0 V red P1 ON white: unused black P1 RUN 4th: unused entry 9, bottom wall 9 PG7, 1/2 in hole PI B’S SIDE (backup) P2 ON: a relay puts backup 24 V on pump 2’s + P2 RUN: WD-B watches it and wakes Pi B at once BatteryProtect remote: Pi B Open: relay module, entries P1 RUN and P2 RUN carry 24 V while their pump runs Colored heat shrink and a label at both ends. Never on a 0 V terminal. Shield: trimmed and sleeved at both ends. J1pump +: switch out (Water Witch tan, Ultima pump lead), manual-on, running J20 V: the feed’s black, the switch’s 0 V lead, pump − J324 V feed: the feed’s red, the switch’s feed lead
+24 V (pump 2: backup battery)0 Vswitch out (on when wet)manual-onunused corepump running signalcablejoint

How it works

  • Water runs the pump, no computer needed. Pump 1: line 11’s 5 A breaker, then Water Witch 1 (turns on when wet 6 to 8 s; runs 15 s more when dry). Pump 2: the backup battery, always: line 15’s 5 A breaker, a BatteryProtect, then the Ultima switch, sealed so the bilge water cannot join the two sides.
  • Two steps by height. The Ultima sits higher: pump 2 starts only if pump 1 falls behind.
  • Pump 2 cannot flatten the backup battery. The BatteryProtect cuts it at about 30% left; its remote input goes to Pi B, so shore can stop a stuck pump 2.
  • Shore can run either pump. Ch 6 puts 24 V on pump 1’s +, after the Water Witch, no diode; pump 2’s manual-on is on Pi B’s side. A dead node leaves ch 6 open.
  • Run signals. Pump 1’s + to opto input 1. WD-B watches pump 2’s running line and wakes Pi B at once; Pi B runs pump 2’s monthly 5-second exercise.
  • Power-up: Water Witch 1 runs pump 1 a few seconds to set itself. Not a leak.

The runs

RunWire
Water Witch 1From the maker: three 16 AWG, 30 in. Red to J3, black to J2, tan to J1. Rated 15 A at 24 V
UltimaJohnson 36303, 10 A at 24 V. Feed to J3, 0 V to J2, pump lead to J1 (colors per Johnson’s sheet)
Pump feedPump 1: 16/2, good to 22 ft. Pump 2: 14/2 (roll on hand). Red to J3, black to J2
Bilge cableC4 18/4 shielded, one piece from node entry 9. Red: P1 ON, after ch 6’s 5 A fuse. Black: P1 RUN, opto input 1. White, 4th: unused, sleeved (ch 12, opto input 2 spare). Shield sleeved both ends
At the pumpsEach pump’s ON and RUN wires join its + at J1, after its switch, no diode (pump 2’s from Pi B’s side)

Rules

  • Every joint above the highest bilge water, sealed. Crimped, never soldered.
  • Service loops so a pump comes out without cutting anything.
  • Dead first (no breaker has an off lever): pump 1, main battery switch off; pump 2, lift one end of the backup board’s 30 A ANL.
  • P1 RUN and P2 RUN carry 24 V while their pump runs: colored heat shrink and labels at both ends, never on a 0 V terminal.
  • Label both ends: P1+, P1−, P1 ON, P1 RUN; same for P2.

Still open

  • The part for J1 and J2 (three wires each) is not set.
  • Where pump 2’s two signal wires enter on Pi B’s side, and which relay module switches its manual-on. The BatteryProtect’s exact cut voltage.

Homes: Build Guide sec 3.6; Electronics and Wiring Plan secs 4.1, 7.6, A3 (entry 9) and A10; Compute Bay Plan sec 11; Backup Battery Board Layout; Water Witch 217/230/230-24 install sheet.